-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Embedded Motherboards
-
ontrons embedded motherboards with a longevity up to 7 years are the ideal solution for a wide variety of applications.As the options for embedded computing continue to expand, choosing the right embedded motherboard becomes more complicated and confusing.In applications where permanence and risk avoidance must be optimized, Kontron's experience in a variety of markets leads customers to the solution that meets their critical programming and cost objectives.
-
Product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
Interface Card
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
Product
C+L Band Broadband Light Source
OPTOWARE-B200
-
Bench top ASE broadband source system with built-in ASE source module has particularities that it can be operated easily and enables its output spectral feature changed variously by controlling pump LDs inside the module. The output of ASE source can be set to the customized feature by controlling the output power of embedded pump LD individually through the provided program. In case optimum ASE output features such as wide broadband (>80nm@-10dBm/nm) and stable output power (<0.02dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. Through the micro processor and FPGA inside, more stable application is possible by combining the real-time monitoring of output power and pump LD status with the high speed feedback routine.
-
Product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
-
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
Interface Card
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Software Applications
-
Excalibur Systems provides software utilities and applications programs to manage data communications for our products, which include Bus Controllers, Bus Monitors, Data Recorders and analytical flight Data Reconstructors. There are different applications for single & multi function MIL-STD-1553 and ARINC-429.
-
Product
Breadboard Module for 34980A
34959A
Breadboard Module
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
12 Channels, ARINC 429/575 Communications
AR1
-
The AR1 provides an ARINC 429/575 communications interface with 12 channels. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer. Each channel is programmable as either Tx or Rx.
-
Product
Soil Mechanics
I.L.A.
-
I.L.A. is a complete slope stability analysis program that also incorporates powerful features for retaining system designing.
-
Product
Automation
Arithmometer Software
-
Arithmometer is used for arithmetic operations with instantaneous signal values coming to the input channels of ADC modules and spectrum analyzers. The indicator displays the current value of the selected arithmetic operation. After starting, the program creates additional virtual channel whose values can be used in all ZETLAB programs.
-
Product
NVIDIA GPU Cards
-
Graphical cards for AI/VR applications with NVIDIA hardware GPUs that provide powerful libraries that can be leveraged to build your programs.
-
Product
ICAP/4 Consumer
-
Looking to build electronic circuitry and watch its operation right on your computer? ICAP/4 Consumer is an easy to use program that does exactly that. ICAP/4 Consumer enables you to quickly construct any type of analog, digital or mixed analog-digital design, apply electrical stimulus, and view signal waveforms throughout the design.
-
Product
C-Size Switching Modules
1260 Series
-
The Astronics 1260 Series C-Size VXI switching modules deliver the convenience of message-based control for ease of programming and a register-based interface for high-speed control.
-
Product
FD-11613, 8-Channel Temperature Input Device for FieldDAQ
785640-01
Temperature Input Module
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
Product
JTAG USB Controller
NetUSB-1149.1/E
Controller
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
PCI Digital I/O
APC424
-
The 16 TTL input/output channels can be programmed as inputs or as outputs on an individual channel basis. The 24 differential input/output channels are programmed as inputs or outputs on an 4-channel port basis. All input channels can be enabled for change of state, low, or high level transition interrupts.
-
Product
REL Link Checker Lite
-
REL Link Checker Lite is a free easy-to-use link checker tool to help you maintain the accuracy of links on your website. The program will help you easily locate broken links and links containing syntactic errors.
-
Product
AI UI Visual Testing Platform
Applitools Eyes
-
Automated Visual Testing of Web, Mobile and Desktop applications. Automatically test all the visual aspects of the applications that they are developing on multiple browsers, multiple Mobile device OSs and form-factors, and multiple programming languages.
-
Product
Windows Driver & SDK for ADLINK PCI/PCI Express/cPCI Series Data Acquisition Cards
PCIS-DASK
Data Acquisition Module
ADLINK PCIS-DASK is an advanced 32-/64-bit kernel driver and 32-bit/64-bitDLL Library for custom data acquisition application development. PCIS-DASK provides a common set of Application Programming Interface (API) for ADLINK"s extensive family of PCI/PCI Express(R)/cPCI Series Data Acquisition Cards, and is ideal for custom applications development under 32-bit/64-bit Windows 7/8. With PCIS-DASK, you can easily access all functionality of ADLINK DAQ PCI/cPCI general series data acquisition cards.
-
Product
XJLink2-3070
-
The XJLink2-3070, approved by Keysight Technologies, provides convenient, integrated access to XJTAG’s powerful boundary scan test and programming tools from Keysight (Agilent) i3070 ICT machines.
-
Product
Moisture Testers for Wood
-
Here you will find a moisture tester for wood to determine absolute moisture in different wood types. Newly-cut logs can have a moisture content of 80% or more, depending on the type. Since wood shrinks substantially when dried, it must be dried before being used in construction or most other applications. This is most often done using a large furnace called a kiln. The air drying method may also be used, but this is much slower. With the help of the moisture tester for wood you will be able to measure with high accuracy moisture in, not only raw wood, but also rolled paper products, planks, slats, beams, plywood, panels, particle board, main beams, window frames, etc., anything wooden. There are two ways of measuring moisture, these two ways are with or without damaging the material. The majority of types of moisture testers we offer at PCE do not damage the wood, or damage it very slightly.The moisture tester for wood is characterized by the measuring principle and the moisture sensors that can be adapted to it. The moisture tester for wood has special characteristics such as an automatic compensation of temperature. Besides, data can be stored and transferred to a PC or laptop, or characteristic curves can be programmed for specific wood types (only with the model FMD). Our moisture tester are of the highest quality standards in the industry, and are durable and easy to use.
-
Product
200KHz / 10000Freq.Point LCR Meter
MCH-2816A
-
It has high test frequency of 300kHz and 0.01Hz stepping arbitrary programming, and it has 10mV-2V signal level, all making it meet the precision test requirements of production line quality control, in-coming inspection and lab. Its HANDLER, RS232c interfaces are used for the component automatic sorting system, which provides the conditions for computer telecommunication and test recording. Flexible frequency-response analysis:Due to non-ideal inductor, capacitor and resistor, in order to precisely evaluate the characteristics of one component in one frequency band, MCH2816 could use its signal generation ability with 10mHz resolution to correctly analyze frequency response of the component parameters in any frequency band. In particular, it can do the precise measuring of the resonant impedance of the low-frequency ceramic resonant devices which has wide impedance range.
-
Product
Consumer/ Rohs Benchtop XRF Analyzers
Xpert
-
The Xpert for Consumer/RoHS, a convenient, compact & lightweight XRF analyzer for regulatory compliance programs, provides accurate Pass/Fail results within seconds. It is completely independent of an external PC and can be powered by battery for ease of transport to wherever testing is needed.
-
Product
Ada Development Environment
GNAT Pro
-
GNAT Pro is a robust and flexible Ada development environment. It comprises a full Ada compiler (Ada 83, Ada 95, and Ada 2005 features) based on the GNU GCC technology, an Integrated Development Environment (GNAT Programming Studio), a comprehensive toolsuite including a visual debugger, and a set of libraries and bindings.
-
Product
IP Gateway
SFT3508F/SFT3508F-10 (SFT3508F-M)
-
Hangzhou Softel Optic Co., Ltd.
*8 Data ports ( SFT3508F/SFT3508F-M) :First Data port: IP out over HTTP, UDP (SPTS), HLS and RTMPData CH1-7 ports: IP in over HTTP, UDP (SPTS), RTP (SPTS), RTSP and HLSIP out over HTTP, HLS and RTMP (Unicast)*10 Data ports ( SFT3508F-10) :First Data port: IP out over HTTP, UDP (SPTS), HLS and RTMPData CH1-9 ports: IP in over HTTP, UDP (SPTS), RTP (SPTS), RTSP and HLSIP out over HTTP, HLS and RTMP (Unicast)*Support TS files uploading through Web management*Support IP anti- jitter function*Support adding scrolling caption, welcome words, boot image and boot video (this function is only applicable to IP out application and the STB/Android TV must be installed SOFTEL IPTV APK)*Support downloading SOFTEL IPTV APK directly from this device *Support about 80 HD/SD programs (Bitrate:2Mbps) When HTTP/RTP/RTSP/HLS is converted into UDP (Multicast),the actual application shall prevail, and suggest maximum 80% CPU utilization*Support program playing with APK downloaded android STB and TV, maximum 150 terminals
-
Product
Pattern Conversion
Wave Wizard
-
Wave Wizard generates a test program according to device spec. It avoids the inherent problems that exist when trying to force an event-driven simulation into a constrained ATE test program, by considering device perspective.
-
Product
Software
PowerPro III
-
Chroma Systems Solutions, Inc.
PowerPro is a feature-rich, expandable automated test platform that gives you control without spending your valuable time programming and allowing you to get your product to market faster.
