Verifiers
-
Product
Cable Verifiers
VDV II Series
-
The new VDV II Series are easy to use cable testers that check the integrity of copper cables commonly found in domestic, commercial or industrial voice, data or video installations, including telephone wiring, data network and video/security cabling.
-
Product
Conformance Calibration Standard Test Card for ITF-14 (Interleaved 2 of 5) Symbol Verifiers
AI-CCS-ITF-14
-
This test card is ideal for testing verifiers, scanners, and other ITF-14 (Interleaved 2 of 5) barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
Product
Portable Bar Code Verifier
Laser Inspector 1000
-
The L1000 analyzes the essential traditional verification parameters including average bar deviation, quiet zones, encodation check, mod check and ratio where applicable. It also provides the ISO/ANSI method Decodability calculation and percent of decode information. Designed for maximum ease of use, even traditionally hard to verify bar codes such as high density codes with 5 mil (.13mm) X dimensions and codes on irregular, wet, shiny, laminated or moving surfaces are accurately analyzed.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm
50-293-022
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Logic Analyzer
FS2352B
-
The FS2352B is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR3 DIMMs. This logic analyzer probe has a CKE qualification circuit that allows for the use of older Keysight logic analysis modules when testing systems using power saving modes.
-
Product
Device Testing
S-TEST Lab
-
SPEKTRA Schwingungstechnik und Akustik GmbH Dresden
S-TEST Lab solutions have been tailored for system level testing in development and lab environments. The core component is the S-TEST desk system. It combines a compact design with the full test interface, that enables the developer to react flexible on changing requirements already in early project phases and to also verify product performance parameters.
-
Product
Multi-Layer Protocol Analyzer
10G-EPON Xpert™
-
The 10G-EPON Xpert is a unique, non-intrusive multi-layer protocol analyzer for 10G-EPON networks and products. It tests and compares the functionality of OLTs and ONUs and verifies the standard compliance and interoperability of 10G-EPON products from different vendors. It is a powerful tool for telecom operators, MSOs and equipment vendors, as well as for technology and chipset companies.
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PNA-X Microwave Network Analyzer
N5241A
Network Analyzer
Reach for unrivaled excellence in your measurements and designs Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the worlds widest range of single-connection measurement applications Test linear and nonlinear device characterization more accurately with the world's best PNA-X Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Functional Testing
-
Interface Testingevaluation of correct system module interaction Smoke Testinginitial testing process to check whether software is ready for further testingSystem Testingconducted on a complete, integrated system to evaluate the system's compliance with its specified requirements Integration Testingperformed to test units of code to verify interaction between various software components and detect interface defectsRegression Testingtesting to ensure changes made are not impacting previously working functionality Acceptance Testingperformed to make sure the software handles required tasks in real-world scenarios, according to specifications
-
Product
Hardness Test Blocks
-
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
Product
Action Counter Tester
-
Weshine Electric Manufacturing Co., Ltd
Lightning strike counters of lighting arrester measure lightning strikes by the induction of current and do not require the use of any external power source. Weshine invented Lightning-strike-counter Tester (VS-451) is used of verify that if strike counter is correctly mounted and connected. As well as output current with sensitivity of 0.01 mA to correct leakage ammeter.
-
Product
Photovoltaic Testers
-
A range of products to verify safety and efficiency of photovoltaic installations. This range includes 1500V I-V Curve Tracers, Insulation testers (IEC/EN62446), designed to provide more and more functional solutions for the activities to be performed.
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
Pressure testing solutions
-
Pressure testing involves applying stored energy to an assembly of parts, in order to verify its strength, its integrity and/or its functionality. Pressure Testing generally uses the application of a test fluid (liquid or gas) into a volume and the fluid is then pressurised to exert pressure forces onto the test object that can be measured.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm - SPST
50-294-113
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Fully Compliant ASi-5 Transceiver ASSP
ASI4U-V5
-
The ASI4U-V5 is the industry’s first silicon solution to fulfill the ASi-5 (Actuator-Sensor-Interface version 5) standard for industrial network equipment that enables comprehensive Industry 4.0 applications. The ASI4U-V5 ASSP comes with a completely verified and field-proven firmware that fully implements ASi-5. Hence, integration of ASi-5 into any application is very easy, as the complexity of the fieldbus is hidden by the chip and the firmware.
-
Product
Alternator Tester
QME-2D
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to fast test generator performance. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing generator (test items difference appear in the different types motor)Test standard.
-
Product
Video and Protocol Analyzer
-
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
Product
Live-Dead-Live Meter Verifier
LDL-1200
-
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
Product
PXI Resistor Module 4-Channel 1R to 255R with SPDT
40-293-113
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Audio Volume Meter
AVM
-
This is a true RMS audio storage meter used to measure audio volume levels of live program material. Use it to periodically survey your system for high or low audio levels to prevent complaints about loud or un-even audio programming. You can use this meter to quickly locate and verify any objectionable signals levels and bring them into compliance.
-
Product
Thermal Imagers
-
Klein Tools’ thermal imagers allow electricians, plumbers, HVAC professionals, home inspectors and other trade professionals to verify systems and troubleshoot problems needing maintenance based on hot and cold spots displayed on LCD.
-
Product
Distortion Detector PLUS
DD-1+
-
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
Product
External Load Module
ELM
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
Name:PoE Tester PRO
Model #:PE-200
-
The PoE Tester Pro is designed for speed testing and verifying standard active and passive PoE networks as well as measuring power level of a PoE system even with reversed polarity on IEEE 802.3 af (PoE), 802.3 at(PoE+) and 802.3bt(PoE++) type3 compliant standard PoE.
-
Product
Ethernet Speed Test Solution
NET-BOX™
-
The NET- BOX is an optimized Quality of Experience (QoE) testing platform that offers a low cost, reliable, high performance FPGA-based alternative to expensive high-end laptops often used for enterprise and speed tests. With a multi-test port architecture, with four 1GE, one 2.5GE test and 4 Gbps full line rate capability, the NET-BOX can truly test the limits to verify Quality of Service (QoS) and assure QoE for the ever growing high-speed internet service at and beyond 1 Gbps.
-
Product
Push Back Probe (VF3) VF383B0004G15L
1011529
-
The Push Back Probe VF383B0004G15L (item number 1011529) is designed to verify that terminals are correctly locked in connector housings. VF383B0004G15L can verify that a terminal remains securely locked in the connector housing and is not pushed back beyond the permitted position during contacting. For VF383B0004G15L, spring force is 1500 cN at a nominal travel of 5 mm. Pointing accuracy for VF383B0004G15L is specified as ±0.1 mm. VF383B0004G15L is rated for 8 A continuous current with a typical contact resistance of 30 mΩ. For installation, VF383B0004G15L uses an M2 x 0.2 thread.





























