Verifiers
-
Product
Logic Analyzer Probe
FS2512
-
The FS2512 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154A/B/64A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs.
-
Product
Partial Discharge Pulse Calibrator
TPK
-
Partial discharge puls calibrator TPK is a battery-powered handheld device for determining the correction factor in a Partial Discharge test circuit and to verify the Partial Discharge measurement.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Information Technology Testing
-
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing information technology products according to applicable standards. We help you not only verify the classification of your product, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
Product
PCI RTD Simulator Card 6-Channel PT100
50-262-101
Simulator
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Logic Analyzer Probe
FS2600A
-
The FS2600A is our newest and fastest logic analyzer probe used to test DDR5 RDIMM and LRDIMM memory. It is designed to work exclusively with 4 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 RDIMM/LRDIMMs and DDR5 Memory Channels.
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Static Design Verification
ALINT-PRO
-
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k with SPDT
40-293-123
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Systems Integration (SIL) Lab Data Acquisition
System
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
Product
Test Sphere Probe
CX-500
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Sphere Probe This sphere is intended to verify the degree of protection of enclosures for an IP2 Code per IEC 529. Sphere is hardened steel with chrome finish. TOP
-
Product
Flow Meter / Monitor
NivuFlow Mobile 600
-
The NivuFlow Mobile 600 was developed particularly for long-term measurements in field operation without external power supply. Measurements for checking and verifying can be carried out with the self-sufficient and portable system without any problems even in harsh environments. Battery lifetimes of several weeks or even months reduce personnel costs for maintenance and data readout significantly.
-
Product
Advanced Ethernet Tester
LinkRunner® 10G
-
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
Product
SCTE35 And DPI Monitoring System
SCM200
-
The SCTE35 splicing message and advertisement insertion monitoring system can be used by service providers to monitor Ad placement opportunities and verify correct Ad insertion. The system will log all SCTE35 messages discovered in the transport streams and perform triggered recording for the verification of Ad insertion process.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Engine Performance Analyzer
H337H-2
-
Verifies engine performance during troubleshooting and after module replacement
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Anite Application Testing
-
Verify higher level protocols and application enablers for a more effective roll-out of LTE-IMS based services to end-usersPerform rapid and cost-effective application testing associated with device acceptance test plans mandated by major mobile operators such as China Mobile, Verizon Wireless, AT&T and T-MobileGain access to comprehensive IMS LTE test plans mandated by standardization organizations such as GCF and PTCRB
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Module 2-Channel 3 Ohm to 131k Ohm - SPST
40-294-134
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Tx/Rx SignalBlade
-
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for backplane path characterization. The card includes a HM-ZD connector segment for access to the backplane and edge-launch SMA connectors for ease of test cable attachment. DC blocking capacitors are included on the receive pairs as required by Advanced TCA.
-
Product
Network Emulator
-
With Simnovus Network Emulator, it is easy to validate if your device works on networks across any region in the world under different network configurations. It supports carrier bandwidth up to 100MHz and frequency ranges from 70MHz to 6GHz for both FDD and TDD. And thanks to the software-based radio (SDR) design, you can also verify custom bands including CBRS.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm
50-293-022
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Conformance Calibration Standard Test Card for ITF-14 (Interleaved 2 of 5) Symbol Verifiers
AI-CCS-ITF-14
-
This test card is ideal for testing verifiers, scanners, and other ITF-14 (Interleaved 2 of 5) barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
Product
Hybrid Verification Platform
HES-DVM
-
HES-DVM™ is a fully automated and scalable hybrid verification environment for SoC and ASIC designs. Utilizing the latest co-emulation standards like SCE-MI or TLM and newest FPGA technology, hardware and software design teams obtain early access to the hardware prototype of the design. Working concurrently with one another they develop and verify high-level code with RTL accuracy and speed-effective SoC emulation or prototyping models reducing test time and a risk of silicon re-spins.
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
