Verifiers
-
product
PNA Microwave Network Analyzer
N5227B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Trailer Wiring Buddy 7 Pin Flat
222
*Each signal from vehicle emits a unique tone *Electric brake control signal illuminates red LED *Loud beep can be heard over shop noise *Time Saver! Just apply brakes, right/left turn signals, running lights, engage reverse & 12 Volt Charging voltage *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Wire Systems Analyzer
Console Test Systems (CTS)
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
product
Tx/Rx BenchBlade
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for logic card characterization. The card includes a HM-ZD male right angle connector segment for access to the Zone 2 connectors of a switch fabric or node card. Edge-launch SMA connectors are utilized for ease of test cable attachment. SMT pads are included on the receive pairs.
-
product
Analyze HBM and CDM Waveforms
WaveAppraise
WaveAppraise is a modern, efficient tool for analyzing HBM and CDM tester waveforms from virtually any source. It can be used independently to verify tester waveforms and is included with GTS PurePulse and Scorpion systems. Download the free version or contact us for information on the premium version.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Barcode Verification Systems
REA PC-Scan LD4
The REA PC-Scan LD4 is a barcode verifier made in Germany which was developed in conformity with international standards. It is especially designed for measuring barcodes with highest precision. The combination of state-of-the-art technology, process reliability and intuitive operation makes the REA PC-Scan LD4 globally unique in its class. Final statements "Pass" or "Fail" are central display elements and enable an immediate result. The simultaneously displayed details allow for an immediate and exact barcode quality analysis.
-
product
Modbus Plant Simulator
If you are an Industrial Control engineer or technician dealing with Modbus RTUs, PLCs, Drivers and SCADA servers, you must have Modbus TCP Plant Simulator is your toolbox. With this tool, you can test and verify your SCADA tag names, IO Server mappings, Modbus addresses, alarms, visualization displays, historians, reports, data communication channel throughput, controls, and more without deploying even one RTU or PLC.
-
product
Viscosity Standards
Brookfield Viscosity Silicone and Oil Standards provide a convenient, reliable way to verify the calibration of your Brookfield laboratory viscometer/rheometer.
-
product
Portable, Integrated O-Level Test Platform
Guardian™
Guardian is a ruggedized automated testing platform that quickly and accurately verifies the operational readiness of complex electronics systems in aircraft, ships, and vehicles.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
C-Band Mini-Tester
Model 38-4
Kratos Defense & Security Solutions, Inc.
The C-Band Mini-Tester (Model 38-4) is a handheld battery powered unit that provides go/no-go testing for compatible C-Band transponders. The Tester verifies proper transponder operation by interrogating a transponder installed in and powered by a platform. It is capable of testing compatible transponders at distances of up to 350 feet. Indicator lights verify the transmission of signals and the received reply.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Cable TV
Tempo Communications provides technicians with an array of test and measurement solutions to optimiz... e the installation and performance of broadband cable networks. The tried-and-true TDR from Tempo delivers all of the enhanced features required to pinpoint faults and verify performance. Like all of its test and measurement devices, the focus is on reliability, ease-of-use, and quality—empowering technicians to do their jobs and exceed customer expectations.Show less
-
product
Day Camera Testing
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
product
Catena 1910 HSIC Tester
Catena 1910
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Leak Testing
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
product
Phase Angle Meter
597C
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
product
Fast Performance Check For Your Moisture Analyzers
SmartCal
SmartCal is an innovative test substance that offers a fast way to verify the performance of your moisture analyzer. Testing it regularly with SmartCal ensures that your moisture measurements are reliable all the time. Learn more about performance testing and how SmartCal ensures trusted results. The SmartCal test takes just 10 minutes and it is done in the same easy way as a regular measurement. It is an ideal reference substance because a specific amount of moisture is released depending on the drying temperature selected. SmartCal measurement reports make it easy to monitor and interpret your instrument's performance over time. Results can be stored directly in the instrument or manually entered into our free validated Excel report sheet.
-
product
Custom Barcodes
Verifier and scanner manufacturers often require custom barcodes for product evaluation, calibration, and quality control. Whether it’s a single code or a composite sheet of multiple codes, symbologies, minimum x dimension, etc., APPLIED IMAGE produces these custom, photo-composed standards to meet the needs of our global base of customers using our proprietary ACCUedge® technology.
-
product
PNA Microwave Network Analyzer
N5225B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Nuclear Safeguard Systems
Nuclear Safeguards are measures to verify that States comply with their international obligations not to use nuclear materials (plutonium, uranium and thorium) for nuclear explosives purposes. Global recognition of the need for such verification is reflected in the requirements of the Treaty on the Non-Proliferation of Nuclear Weapons (NPT) for the application of safeguards by the International Atomic Energy Agency (IAEA). Also, the Treaty Establishing the European Atomic Energy Community (the Euratom Treaty) includes requirements for the application of safeguards by the European Commission. Organizations such as the IAEA and EURATOM and others are tasked with ensuring declared amounts of material are indeed present in the facilities in which they are stored and that such material is not being diverted to other uses.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
NVIDIA® Jetson™ TX2-based Industrial AI Smart Camera for the Edge
NEON-2000-JT2 Series
ADLINK's NEON-2000 Series of the NVIDIA® Jetson™ based industrial AI cameras, integrate the Jetson™ Xavier NX or Jetson™ TX2, image sensor, optimized OS, and Rich I/O for vision applications in a compact chassis with verified thermal performance, saving users' Total Cost Ownership on integration and trouble shooting, as well as minizing footprint and cableing required for installation.
-
product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Webmaster Tools
A1
Sitemap, keywords, analyzer, downloader, scraper, search engine for Windows and Mac OS X. Need to analyze your entire website for errors and possible improvements? You can spell check, improve internal linking, validate HTML and CSS, verify all pages have Google Analytics installed and more with A1 Website Analyzer.
-
product
Databus-to-Network Interfaces
OBB2
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
product
PXI RTD Simulator Module 6-Channel PT100
40-262-101
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.





























