-
Product
C Series Universal Analog Input Module
Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Universal Gauging
-
To improve the quality of your large diameter machined parts, the portable Universal Setting Gauge from Bowers has been developed as an easy to use comparator tool which can be set up next to the gauge being utilised. This Universal Setting Gauge has been designed to improve the ongoing accuracy levels; when setting the master, the spring loaded setting anvil ensures a constant force is maintained thereby giving repeatable setting readings. The Bowers Universal Gauge’s ingenious modular format enables it to be quickly configured to suit almost any measuring challenge.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
High Current DC Load
3350F Series
-
3350F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232、USB and LAN interface.
-
Product
Battery Data Logger
BDL-3926C
-
Kongter Test & Measurement Co., Limited
BDL-3926C Battery Data Logger is wireless monitoring device for string voltage, cell voltage, current and temperature. It works individually to reflect battery status or co-works with Kongter’s other battery test equipments like battery charger and K-3980 DC load bank. For different battery systems, it has customized configuration from 12V to 480V or upper. And it has easy expansion for all battery systems.
-
Product
STM32 Arm Cortex MPUs
-
As Industrial, Consumer, Smart Home, Health and Wellness systems are growing more connected, certain embedded designs are now required to manage high processing loads and complex applications with rich Human Machine Interfaces (HMI). Under these conditions, the ability to harness open-source software stacks while maintaining low power and real-time performance are key requirements.
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Load Testing
-
Load Testing, Simplified. We sort out the infrastructure, so you can spend more time testing. Tool Agnostic - We support JMeter, Gatling, Capybara and Selenium. Unfettered Testing - No limits on how you test, run as many users for as many tests, for as long as you like. Third-party Integration - Send results to Slack, Hipchat, Flowdock, or your own services using our API.
-
Product
PXI 10A Power Multiplexer, 2-Bank, 8-Channel
40-661A-102
Multiplexer Module
The 40-661A-102 is a single pole, 2-bank, 8-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Universal Testing Machine:UTM Micro
-
Until now, testing of very delicate and small mechanical parts such as bearings, springs, microwires, organic fibers, and micro-electro-mechanical devices was not possible with conventional universal testing machines. But Anton Paar’s universal testing machine, UTM Micro, based on the renowned Anton Paar MCR rheometer, opens up a new world of material testing. The versatile UTM machine’s sensitive MCR technology, combined with its proven modularity, and an integrated extensometer and load cell, allows you to go beyond just tensile testing. You’ll now be able to rise to all kinds of challenges, even in the fields of DMA and optical methods.
-
Product
6GHz SMA Calibration Kits
CAL-SMA-6F
-
The CAL-SMA-6F Full calibration kit provides all elements for Male and Female Open-Short-Load and Through calibrations for one and two port VNA measurements.
-
Product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
Product
Multi-Unit Controllers
-
Mosebach Manufacturing Company
Mosebach’s Multi-Unit Controllers are built to help you manage your load banks in operation – whether 10, 20 or 500 units ganged together.
-
Product
Compliance and Data Protection
-
Locate and protect sensitive and PII data to identify risk and ensure compliance. Monitor system events to identify and proactively respond to potential risks and bad actors. Simplify security operations, reduce risk and lighten security management load with automated ID and authorization cleanup.
-
Product
PXI 5A Mux 2-Bank 24-Ch Isolated COM + Ind Isolation
40-651-112
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Portable Load Cell System
-
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ twin female contacts
510160105
Receiver Module
Comes fully loaded with twin female contacts ( p/n 610138200).QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O.Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Expendable Refrigerant Chambers
LDF Series
-
The Bemco LDF Series of wide range expendable refrigerant chambers are designed for low initial cost, rapid temperature cycling, environmental stress screening (ESS), and for handling large thermal loads. These systems are compact for their size, can be bench mounted, and are easily modified to special testing configurations.
-
Product
DC Electronic Load
63600 series
-
Chroma's 63600 series DC electronic loads are designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, server power supplies, and power electronic components. They are excellent for research, development, produc t ion, and incoming inspection applications. The 63600's state of the art design uses DSP technology to simulate non-linear loads using a unique CZ operation mode allowing realistic loading behavior. The 63600 series can draw its rated current under very low voltage (0.4V typical). This unique feature guarantees the best loading performance for modern Point-of-Load conditions and fuel cells.
-
Product
Power Phase Converter Single phase 220VAC to 3 phase 380VAC Converter
SDT-40KW
-
Zhejiang Sandi Electric Co., Ltd
SANDI SDT series single-phase to three-phase converter, adopted SVPWM modulation control technology, which can convert ordinary single-phase power to industrial three-phase power. After through SDT series single-phase to three phase converter power conversion, the three-phase power output is standard pure sine wave, the harmonic distortion rate (THD) is less than 2%, totally meet the national standards of three-phase power quality, applicable to all types of load.
-
Product
Rockwell Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement；◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement；◆ Friendly human-computer interaction，5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc； ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR；◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes；◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table；◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages；◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis；◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data；◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis；◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.
-
Product
Regenerative Power System
IT6000B Series
-
From the perspective of improving customer experience, ITECH launches a new incorporated product--IT6000B series. IT6000B integrates bidirectional power supply and regenerative electronic load into one 3U unit. It is also a very powerful one. Only a button is needed to switch between the bidirectional power supply and the regenerative electronic load.
-
Product
Data Center Load Bank
-
Mosebach Manufacturing Company
Mosebach’s Data Center Server Rack load bank, the SR family, is ideal for commissioning data centers. There are multiple models for varying voltages and power levels. The unit has a variable fan speed control which allows you to fine tune as desired.
-
Product
300W to 400W - Single Output
CFE Series
-
*Medical & ITE Safety Certifications (BF rated)*94% Efficient*0.5W Standby Power*Meets ErP Stage 2*450W Peak Loading (10s)*Suitable for 1U applications*Five year warranty
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors
40-153-002
Relay
The 40/42-153-002 is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
8Ch Speaker/Receiver Unit Tester
BK9012
-
Based on the BK2120A Audio Analyzer, the BK9012 is designed to quickly test microspeakers or receivers 4~8 at a time at a rate that you’ll find hard to keep up with. It tests various frequency characteristics and also rub & buzz so you know the quality of your product is maintained. And of course, you can track the accuracy and stability of your process using the data you’ve saved on about 4 million microspeakers (based on a 6 second total test + load time) per month.
-
Product
PXI/PXIe Power Relay Module, 50xSPST, 5 Amp, 50-Pin SGMC Connectors
40-153-001
Relay
The 40/42-153-001 is a PXI/PXIe high density power relay module with 50xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
