-
Product
Power Supplies
ZPG-700B
-
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
HCU/DC-DC Converter ATS
8900
DC Converter
Low power testSleep mode current testInput overvoltage limit testLine regulation testEfficiency testLoad regulation testOutput ripple voltage testDC-DC load testOvercurrent testPower doen and isolation test
-
Product
Computer Control Torsion Testing Machine
NDW Series
-
Jinan Testing Equipment IE Corporation
NDW Series computerized torsion testing machine provides loading and weighing capabilities in both rotation directions which enables it to determine conveniently not only the ultimate torque of a specimen, but also how the specimen behaves under conditions of continuous or intermittent torque loading in both directions. The computerized torsion testing machine is mainly used for the torsion test of metal and non-metal materials, as well as the torsion test for parts and components. The computerized torsion torsion testing machine is an essential instrument to measure torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
Product
WaveLink Temperature Extension cables for Dx10
Dx10-HiTemp
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
-
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
True AC RMS Panel Meter
-
The Laureate? True RMS meter offers a high accuracy 4 1/2 digit display for five voltage ranges and four current ranges. It is suited for AC applications where there is considerable distortion of current waveforms from nonlinear loading. The input is AC coupled to read only the AC component, such as ripple on a power supply.
-
Product
Miniature Shock Absorbers
-
Miniature shock absorbers from ACE are tried-and-tested quality products used in millions of industrial designs throughout the world. They optimize machines in an equally reliable and effective way by decelerating loads quickly and without recoil.
-
Product
Charge Controller
-
The intelligence of an AC charging station or an AC charging infrastructure is largely determined by the charge controller used. A smart charge controller has the primary task of controlling and monitoring the charging process of an electrical vehicle.The features that characterise a smart charge controller include communication with a backend system and the associated authorisation of users, as well as the efficient distribution of load currents by means of dynamic load management to prevent an overload of the existing AC system.
-
Product
Charger/Discharger Complex
K-3986
-
Kongter Test & Measurement Co., Limited
K-3986 is not only a battery charger or load unit for battery String. It is comprehensive unit with one-stop-solution for battery maintenance. With charging and discharging for the same battery string, it will greatly simplify your maintenance for batteries. Extra functions like wireless online monitoring and battery activation will enable you to know your batteries comprehensively. With optional DAC, you could also have a real time monitor for the whole process of measurement.
-
Product
Passive Probe, 10:1/1:1, 350 MHz, 1.3m
N2889A
Oscilloscope Probe
The Keysight N2889A low-cost passive probe provides up to 350 MHz bandwidth and features high-input resistance of 10 MΩ (@10:1 mode) to address a wide range of measurement needs with low probe loading. The N2889A comes with a convenient switch in the probe handle that lets you switch between a 1:1 and 10:1 attenuation ratio.
-
Product
VCORE Power Test
-
To support the heavy computing loads required by AI technologies, system servers must rely on high performance CPUs and GPUs capable of complex, real-time processing. These processors are powered by VCORE power supplies, embedded DC/DC converters, or voltage regulator modules (VRMs).
-
Product
API Load Testing
loadUI NG Pro
-
With a visual, drag-and-drop interface, loadUI allows you to create, configure and redistribute your Load Tests interactively and in real-time. In a single test environment, loadUI provides complete test coverage and supports all the standard protocols and technologies. And it''s so powerful, it generates scalable, high-volume and real-world load from any number of local and remote computers. Meet loadUI, the future of Load Testing.
-
Product
Power Factor RLC Load
3282（280V,1875W / 3700VA ）
-
3282 power Factor RLC Load built-in 16-bit A/D and DSP precision measurement circuit, provides accurate measurements, measurement items have Vrms, Arms, Watt, VA, CF, PF, THD, VTHD, ITHD, Ipeak, Amax, Amin, Vmax, and Vmin. In addition to these measurement functions, it also provides time measurement，products such as UPS, fuses and circuit breakers etc. trip or blow time and transfer time for Off-line UPS
-
Product
The DC System Analysis Module
-
Save time with intuitive scenario manager interface.• Communicate designs effectively with graphical and text base results.• Improve decisions by quickly comparing resulting curves from different scenarios.• Increase productivity by modeling both DC and AC systems in a single project.• Reduce mistakes by evaluating all loading conditions and duty cycle loads.
-
Product
High Current Transformers
-
High Current Transformer is designed to elevate and check the temperature of the conductors at high current levels, in order to simulate the current loading conditions found in electrical circuits. High Current Transformer is designed as an open type transformer that uses the test object as its secondary coil or has 1 or 2-turn self secondary winding. The conductors cores' temperature depends on the short-circuit high current caused by the test object. According to the current going through the test object, the test temperature of the conductor will change. The loop temperature is measured by a thermocouple probe which is directly connected to conductor.
-
Product
Signal Averaging eXpert FPGA DSP Feature for CompuScope Digitizers
Digitizer
Utilizing the eXpert Signal Averaging Firmware on a GaGe CompuScope Digitizer allows users to detect a small repetitive signal in a noisy environment by conducting rapid signal averaging completely on the digitizer's onboard FPGA with absolutely no host system CPU loading.
-
Product
Brakes
-
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
-
Product
12-Ch 10A RCV Power Distribution Unit
AR438
Switch Module
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
Product
Instrument Software for SPC- and DPC Modules
SPCM
-
*Multifunctional 64 bit Data Acquisition Software*Recording of Multi-Dimensional TCSPC Results and Time-Tag Data*Control of Multi-Dimensional Recording Features*Configurable User Interface*Acquisition of Decay Curves, FCS, MCS Traces, FLIM and PLIM Images*Online Calculation and Display of FLIM, PLIM, FCS, PCH, MCS Traces and Fit of FCS Curves*Different Operation Modes Available*Measurement Control of Up to 4 Modules*Configurable for Different Instrument Configurations*Accumulation and Autosave Functions*Integrated Scanner Control*Saving, Loading and Conversion of Photon Distributions, Images and Time-Tag Data*Saving and Loading of Results and System Parameters*Integrated Control of Ti:Sa Lasers*Integrated Control of Motor Stages
-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
Mini-Test Station
-
Mini-Test Station for low current fuel cell testing. The test station includes Analog mass flow controllers for Anode and Cathode gas streams, humidity bottles with preheaters and temperature controllers and a cell temperature controller. The test station is designed to use the customer's Potentiostat to load the cell. Manual backpressure is provided for pressures from 0-60 psig. The Mini-Test station is basically our Analog Mass Flow Controlled Low Flow Humidification System with all the options.
-
Product
3U VPX 1 Slot Power & Ground
101V301P03-9001R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Wheel Running Tester up to 15000 kg axle load
MINC II EURO | VP 420005
-
Maschinenbau Haldenwang GmbH & Co. KG.
The test lane-compatible MINC II EURO guarantees a verification of the axle geometry in seconds when the test vehicle drives over (up to 15.0 t axle load) as well as a fully automatic evaluation of the deviation in m / km. The measured values are displayed either in analog form on a dial or by transmission to a PC screen (including graphic representation).
-
Product
Machine Vision System
CVX Series
-
he CVX Series is loaded with powerful features that support GLOBAL STANDARDS in machine vision inspection. State-of-the-art algorithms, that can be set by any user, ensure quick setup and long-term reliability. The best solution can be selected from a variety of options. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. 3D measurement. Ultra high-resolution 21 megapixel camera
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Scale / Weight Meter
-
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
Product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
Source Measure Unit
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
Software Development Kit for ARINC 615A Targets
A615A-TGT-SDK
-
Avionics Interface Technologies
ARINC 615A Data Loader Target development kit enables systems developers to embed ARINC 615A compliant data load functionality into avionics target applications.
