-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Single Board Computers
EPX-C414
-
WINSYSTEMS’ EPX-C414 is an EPIC-compatible single board computer using Intel®’s Bay Trail E3845 or E3825 processor. Its rugged design and extended operational temperature make it a great fit for industrial IoT applications and embedded systems in the industrial control, transportation, Mil/COTS, and energy markets
-
Product
Shelf Manager Carrier/Mezzanine Board for CompactPCI
064-758
-
Set of Shelf manager mezzanine board installed on the pluggable carrier board. The pluggable carrier board provides all interfaces on the rear connectors.
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
Bus Extender
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
6U VME Multifunction I/O Board
64G5
Multifunction I/O
NAI's latest generation 6U VME multifunction I/O and communications board, the 64G5, can be configured with up to six intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance, board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
Product
3U VPX VITA 66.5 FPGA board with FMC+ Site
IC-FEP-VPX3f
-
Based on the latest Xilinx Kintex® UltraScale™ 20nm FPGA family, the IC-FEP-VPX3f is the first VITA 66.5 compliant FPGA board available. It is the perfect solution for applications requiring DSP-intensive processing in a 3U VPX form factor.
-
Product
5 Channel DAC FMC Module
DACNF05 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF05 is a five channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A. A single-ended external input or output clock is provided. The direction of the clock is programmable from the FPGA of the FMC carrier board.
-
Product
Software Tool Especially Designed for Production Process Supervision
LEON OP
-
The Leon OP is a software tool especially designed for production process supervision. Therefore, the application provides the following key features:- Execution of KT ICT sequences or NI TestStand sequences- Parallel, semi-parallel or sequential execution of test sequences, individually definable per Test Sequence- Customizable User Interface, simple or detailed test views, grid or board layout arrangement possibilities- Tracing into sequence execution- User management with different user levels and restrictions per user group- Displaying execution results and statistics by panel or nest- Supporting interaction with an automation (e.g.: handler system)- Supporting interaction with a process control / MES system- Integrated Callback structure to adopt to different workflows- Maintenance view for fast displaying of fails inside a board- Result History View to quickly access the last test results- Store execution results in result files with user defined format- Autostart-option for running application in automation mode without any operator interaction at all- Several abortion criteria to abort execution by fail count (consecutive or time based)- A Maintenance View for viewing testprobe locations on the DUT is available via Aster Quadview
-
Product
SparkFun ToF Range Finder Sensor for VL6180
VL6180
-
This is the SparkFun "Time-of-Flight" Range Finder, a sensor board for the VL6180 distance sensor. Unlike most distance sensors that rely on reflected light intensity or reflected angles to determine range, the VL6180 uses a precise clock to measure the time it takes light to bounce back from a surface. This affords the ToF Range Finder and VL6180 a great benefit over other methods because it can be much more accurate and more immune to noise. Does this technology sound familiar? Well it should, it's the same means cellphones use to detect when the caller is holding their phone to their ear.
-
Product
RELIABILITY BOARD (Reliability Test Board)
-
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
Product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
miniPCI POST Code Display
post5a1
-
MiniPCI format to fit WRAP boards and most modern notebook PCs. During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (auto select, whichever is written first). Use post5a1 to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails.
-
Product
Large Photo Signal Generator
DDS9m
-
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
Product
Software And Tools
-
Renesas Electronics offers high-quality software, high-function and easy-to-use development tools, an abundant boards & kits lineup for development environment for Renesas microcontrollers and microprocessors. This fully designed development environment helps you develop your system more effectively and efficiently; reduces your development time and cost yet improves the quality of system. Furthermore, we offer various third party products and they will also enable you to have development environment best fit to your needs.
-
Product
Mezzanine Carrier
VXI NM-M
-
HM-M is a carrier of mezzanine modules in the VXI standard, it is a VXI module of the size C-1. NM-M ensures the functioning of various modules installed in it, made in the form of mezzanines. NM-M is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog. The carrier of the NM-M mezzanine modules is used as part of information measuring systems based on the VXIbus trunk. Made on a C size board in accordance with the requirements of the IEEE Std 1155-1992 standard.
-
Product
Board Fault Locator
SYSTEM 8 (BFL)
-
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
Product
Isolated Analog Input Expansion Board
MSXB 084
-
The MSXB 084 Isolated Analog Input Expansion Board provides isolated analog inputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
-
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
Digital I/O Module
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
Product
8" Cables
RCONP1553-1
-
Transitions from each card end (non-IRIG) connector on various boards into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 8" cables with BNC cable jacks for I/O triggers.
-
Product
6U Compact PCI® Single Board Computer
CP62007N
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007N is a 6U CompactPCI® single board computer designed by LinkedHope® based on Intel® QM87 chipset. The compact and space-saving processor board meets the PICMG® CompactPCI® specifications. There are SATAIII, USB3.0, Gigabit Ethernet, and Keyboard/Mouse interfaces on the board. CP62007N supports 64GB SSD, facilitating the operating system installing.Part of CP62007N’s rear I/O uses high speed ZD connectors for transferring PCIe2.0, USB3.0, SATAIII and other high speed signals, leading to 2x 8 PCIe (to J3-J4) and a 1x 8 PCIe to XMC. All the PCIe is flexible configuration, for instance, a 2x 8 PCIe can be set into 2 x8, 1 x8 + 2 x4, or 4 x4.
-
Product
Computer-on-Modules
-
The Computer-on-Module (or System-on-Module as some people call them) was born when the embedded computer industry realised the benefits of separating a single board computer into two distinct parts.
-
Product
ESD Protection
-
Protection against electrostatic discharges (ESD) is part of EMC Immunity (Electro Magnetic Compatibility) requirements. It is the ability for equipment to properly operate in its electromagnetic environment by limiting the reception of electromagnetic energy that may cause physical damage. ESD can be either conducted under the form of a transient voltage or can be radiated due to its fast rising time: powerful harmonics will generate erratic behavior by the application by coupling with other signals. Printed circuit boards must be protected against the effects of electrostatic discharge.
-
Product
Chip Scale TVS Arrays
-
ProTek's patented* Flip Chip TVS Arrays are designed for small circuit board applications with limited size and space availability. To reduce installation costs, the Flip Chip can be mounted directly onto the printed circuit board; similar to chip resistors and capacitors. These devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Personal Digital Assistants (PDAs), Laptops and Pagers.
-
Product
Capacitance Sensor Systems
-
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
Product
SparkFun I2S Audio Breakout
MAX98357A
-
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
PCI Express 16 Isolated Input Digital Interface (3-13V)
8006e
-
The 8006e PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
