-
product
96-Pin Micro-D Connector Block, Male DIN Rail Mounted
40-966-096-M
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Axial Extensometer
Model 3542
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
product
RF Connectors
PSMP Connectors
Amphenol RF PSMP connectors are the perfect solution for board-to-board applications requiring high power. With a minimum board spacing of 12.6 mm, the three-piece design allows maximum flexibility for high-density board spacing, and is an ideal solution for blindmate situations.
-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
8-port Serial Interface, Modular, With/without Optical Isolation, 3.3V/5V
APCIE-7800
The APCIE-7xxx series of ADDI-DATA allows you to implement either 1, 2, 4 or 8 modules on serial interface boards.
-
product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-F
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
product
K-Base Test Board Adapter
1180
The TESCO K-Base Test Board Adapter allow quick, convenient testing of self-contained K-Base meters on test boards designed for socket type meters. The K-Base Test Board Adapters are designed for single phase (Catalog No. 1180-2) and polyphase (Catalog No. 1180-4).
-
product
Computer-on-Modules
Arm-based Computer-on-Module with OSM, SMARC, Qseven, rugged RTX, and COM Express Type 7 as well as embedded board design services.
-
product
Multi Protocol 8000 Modules
The M8K module can be one of many protocols that is used on a variety of platforms for the 8000 Multi Protocol Board.
-
product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
product
Plugbord
3719-1
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. No circuit pattern edge contacts only.Unrestricted component placement over entire board surfaceRow and column legends provided
-
product
Portable Ruggedized Test System
BADGER
Badger systems utilize NI's CompactRIO (cRIO), Single Board RIO (sbRIO), and/or CompactDAQ (cDAQ) hardware. The Badger product line offers high speed data acquisition/control and flexibility in an industrial package. Badger chassis and instrumentation have a 50 g shock ratings and a wide -40 to 70 °C operating temperature. These systems are ideal for automotive, industrial automation, remote monitoring, field service, and advanced control applications.
-
product
Micro Sensor
MIC 1000-20
Advanced Thermal Solutions, Inc.
The MIC 1000-20 micro sensor is designed for measuring fluid velocity and temperature in areas that are densely packed. It can be used where the space between boards is less than 4 mm. The thickest part of the MIC 1000 is just 3.2 mm.
-
product
3U VPX Board
VP32101
LinkedHope Intelligent Technologies Co.,Ltd.
Compatible with PC architecture, VP32101 is a low power-consumption 3U VPX board which supports Intel® Atom™ Bay Trail E3800 processors. Combined with up to 4GB DDR3L onboard memory and up to 64GB SATA SSD, the stability and high performance of VP32101 is best guaranteed in harsh and vibration environment.VP32101 provides rich I/O interfaces, including 2x SATA 300, 2x 1000Base-BX/T, 2x RS232/422/485, 3x USB 2.0, 1x USB 3.0, 2x CAN, 1x DP++, etc.To help users develop solutions easily and fast, LinkedHope® equips VP32101 with various BSP, including Windows, VxWorks, Linux and QNX.Apart from the traditional Air Cooling version, VP32101 provides a Conduction Cooling version to guarantee its performance in extreme environment and in an extended working temperature (from -40℃ to +70℃).
-
product
Burn-In Boards
Meets burn-in requirements, including extreme temperatures or continual handling. 2 or more layers of polyimide. 200 C maximum temperature. Gold-plated connectors.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - PCIe
Model 78760
Model 78760 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter, it is suitable for connection to HF or IF ports of a communications or radar system.
-
product
Kelvin Test Contactor
nano
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
product
Indoor Gunshot Detection & Localization
SHOTPOINT
Shotpoint’s indoor sensor includes the basic sensor board in a rugged plastic enclosure with an additional PoE module. The enclosure includes a mounting ring that attaches to a 1-gang electrical box or low voltage frame for easy mounting to walls and/or ceilings. Two(2) sensors with 165ft maximum spacing provide total area coverage and peace of mind in any indoor space.
-
product
Mini UHF Connectors
Pasternack Mini UHF connector category has many part numbers, most of which are RoHS and REACH compliant. Mini UHF connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These Mini-UHF connectors are built to precise RF and microwave industry specifications. Mini-UHF connector products are manufactured in male or female gender with 50 Ohm impedance. UHF mini connector products are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These connector series in mini UHF designs include crimp/solder or solder attachment methods. Other mini-UHF connector options include Push-On or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this mini UHF connector series is in-stock. Not only are these in stock, they will ship the same day as well.
-
product
Automotive
SCHILLER AUTOMATION GmbH & Co. KG
Automotive Product fixtures supports the 100/1000/MultiGBASE-T1 Compliancy standards with many different connectors such as MateNet (TE), H-MTD (Rosenberger), Mini50 (Molex). Also, we provide generic solder down board to enable engineers ability to connect their connector of choice.
-
product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 58610
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
product
Eight and Four Channel Quadrature Encoder Input Cards
mPCIe-QUAD
The mPCIe-QUAD-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to two DB-37F Modules via included 9” cables. The mPCIe-QUAD-4 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to one DB-37F Module via an included 9” cable. The modules are designed to be easily panel-mounted in any application environment, and have convenient mounting holes for non-panel-mount applications. Up to eight differential (or single-ended) encoders (each with A, B, and Index) can be monitored simultaneously.
-
product
AMD Zynq™ UltraScale+™ MPSoC XMC Board
IC-MPS-XMCa
The IC-MPS-XMCa is a XMC FPGA card based on the AMD Zynq™ Ultrascale+™ ZU4CG MultiProcessor SoC.
