-
Product
QSeven
ROM-7510
-
*TI Sitara AM5728 Dual core cortex-A15 1.5GHz high performance processor*Onboard DDR3 memory 2 GB and eMMC Flash 8 GB*Support 1 LVDS, 1 HDMI, 1 USB2.0 OTG, 4 USB2.0 HOST, 1 USB3.0,2 UART, 1 CAN, 1 SATA, 2 I2C, 1 I2S, 2 PCIE 1 lane,*Operating temperature 0 ~ 60 °C / -40 ~ 85 °C*Supports Linux Yocto
-
Product
(8×32)-Ch 0,5A-200VAC Matrix
YAV90062
Matrix Switch Module
256 relays SPST matrix (4×64 1 pole) or (4×32 2 poles). Max switching 10W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
ARM 9 System on Module
MS 1515
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
Product
5G Router
ICR-4461W3S
-
ICR-4400, GLOBAL, NAM, 5x Ethernet, 1x RS232, 1x RS485, CAN, PoE PSE+, Wi-Fi, SFP, USB, SD, Without Accessories. 5G NR Cellular Connectivity, Sub-6GHz. 3GPP Release 16, Support both NSA and SA modes. Quad-core CPU with 1 GB RAM.
-
Product
2x (1 to 8) 50 Ohm 2.5GHz Mux with Self Test Relays
YAVAM308
Multiplexer Module
5x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxSelftest functionMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Reflexive
-
Product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
-
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
Product
Pressure Transducers with CAN Bus Interface
P66
-
The Validyne model P66 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via CAN Bus provides remote zero and span adjustment as well as digital pressure readings in engineering units or pressure counts.
-
Product
Embedded Computer
ARCX-4000
-
Typical applications include military/aerospace deployable systems such as: vetronics, C4ISR, payload management, as well as command and control for drones and robotics. More specifically the ARCX is perfect as a portable data acquisition system in an aircraft by adding a 1553 interface board to a dual unit. Add a FPGA and high-speed graphics card for high-speed video transfer. For multi-sensor monitoring on mobile applications simply add a CAN bus interface.
-
Product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
-
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
Product
Interface Converter
ZET 7176
-
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
Product
Signal Generator
ZET 7192
-
*Analogue two-channels generator*Random profile signal formation*CAN 2.0 data interface
-
Product
High Speed LAN Router
ICR-4401S
-
ICR-4400, GLOBAL, 5× ETH, 1× RS232, 1× RS485, CAN, PoE PSE+, SFP, USB, SD, No ACC. Quad-core CPU with 1 GB RAM, 5× Gigabit Ethernet, 4× POE+ PSE (PoE use is limited – see the ICR-4401 user manual) SFP Connector for SFP modules up to 10 Gbps.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
ARM LPC2294 Based Board
MS 2500
-
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
Product
Yocto/Android 10.1" Touch Panel Computer With ARM Cortex™-A53 Processor
TPC-110W
-
arm SystemReady IR certified.NXP® ARM® Cortex™-A53 i.MX 8M Mini quad-core processor.10.1" 16:9 LCD with multi-touch P-CAP and true-flat IP66-rated front panel.Up to 4 GB DDR4 RAM and 16 GB eMMC storage onboard.2 x 10/100/1000 Mbps LANs with optional IEEE 802.3at/af PoE-PD module support.1 mb FRAM backup memory for unexpected power interruptions.2 x Serial port with 120Ω termination resistor that one supports the CAN 2.0B protocol and offers a programmable bit rate of up to 1 Mb/sec.Embedded browser and for rapid Web App development.Supports Linux Yocto and Android.
-
Product
Switched Power Distribution Module, CAN Control
H730008GS
Switched Power Distribution Unit
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
32-Ch SPDT 2A-240VAC 24VDC Switching
YAV90133
Relay
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Connector and Breakout Box
ES4640
-
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Product
Measuring Systems For Beverage Can Manufacture
RICOS - Specialized Ring Contour Gauge For Drawing Dies
-
Optik Elektronik Gerätetechnik GmbH
Special designed for measurement of inside profile (land angles) of ironing dies for 2-piece beverage can manufacture, tolerance model and comparison with CAD data. Measuring task of RICOS is the measurement and evaluation of the inside profile of ironing rings in beverage can manufacture The measuring and evaluation system RICOS serve the profile measurement and the tolerance evaluation of ironing rings for beverage can manufacture.
-
Product
MINIATURE SILICON DIODE TEMPERATURE SENSOR, 2 To 600 Degress Kelvin
-
Insight Product Company offers SILICON DIODE TEMPERATURE SENSORS CAN BE USED FOR TEMPERATURE Â MEASUREMENTS IN DIFFERENT FIELDS OF CRYOGENIC ENGINEERING AND EXPERIMENTAL PHYSICS. THEY ARE MINIATURE AND OPERATE IN THE TEMPERATURE RANGE FROM 2 TO 600 K.
-
Product
3U OpenVPX High Density Multifunction I/O Board
68CB6
Multifunction I/O
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
Product
Measuring Systems For Beverage Can Manufacture
Cross Hatch Machine
-
Optik Elektronik Gerätetechnik GmbH
Uniform crosshatch pattern on a punch, specific for the beverage can industry.
-
Product
Data Acquisition (DAQ) Software - Dewesoft X
-
Data Acquisition (DAQ) SoftwareDewesoft has been developing leading data acquisition (DAQ) software for more than 20 years. Dewesoft X is the world's best data acquisition (DAQ), data recording, and data analysis software.The software received multiple international awards, is innovative, very easy to use, and requires no programming to acquire, store and analyze data synchronized from several data sources - analog, digital, CAN, CAN FD, CXP, GPS, video, serial and many other data interfaces.Our DAQ software is included for free to all of our data acquisition systems and we offer FREE support and FREE software upgrades forever. No hidden costs. Using our software is easier than riding a bike and has been trusted for years by the world's biggest brands like NASA, Space X, Airbus, Boeing, General Motors, Audi, Ferrari, VW, Tesla, Honda, Toyota, Caterpillar, John Deere to name just a few.
-
Product
Multi Protocol Boards
-
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
Product
CAN Sensoy/ Interface
Strain
-
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
Measuring Systems For Beverage Can Manufacture
OTP – Optical Tool Profile Gauge
-
Optik Elektronik Gerätetechnik GmbH
Optical measuring system for the inside profile of drawing dies for the 2-piece can manufacture.
