Signaling Testers
-
product
Compression Tester
CT66K
Tests compression on all domestic and imported cars and trucks with gasoline engines. Side release valve allows quick re-testing of cylinder without removing the tester or adapter. Large 2-1/2" gauge with dual inch/metric readings: 0-300psi and 0 to 21 kg/cm2.
-
product
LCM Tester
Model 27011
To meet the high accuracy and low price requirements for LCM Test device, Chroma 27011 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL signal source fully complies with the digital signal standard, meanwhile with the 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight or LCM test without obtaining external power source.
-
product
Heavy Duty Circuit Tester
27000
Designed for testing electrical circuits and locating shorts, grounds, and open circuits. Electrical circuit tester available for checking 6V and 12V systems. Heavy duty battery clip .
-
product
Sensor Signal Emulator
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
product
Battery Tester
6470 BT
Standard Electric Works Co., Ltd
2000 counts. DC Voltage measurement. 4-wire resistance measurement. Data hold function. Low battery indication. 9V DC power supply. Measure battery types: Li-ion, Ni-Cd, Ni-MH. Simple operation. Lead resistance and contact resistance eliminated.
-
product
UXG X-Series Agile Signal Generator, 10 MHz to 40 GHz
N5193A
Get closer to reality: simulate increasingly complex signal environments for radar, EW & antenna-test Test sooner & increase confidence in EW systems by generating signal simulations when you need them: the UXG is a scalable threat simulator Use pulse descriptor words (PDWs) to generate long pulse trains & individually control pulse characteristics Accurately simulate multi-threat environments: 180-ns PDW update rate, chirps 10 to 25% of carrier frequency, pulses as narrow as 10 ns
-
product
PC Based Tester
Cablescan L8
The Cablescan L8 provide the PC-based power of the larger PC based testers, but in an economical package for users who do not require more than 1024 test points. This analyzer is designed to operate under the control of your PC.
-
product
High Load Strength Tester
HLST1000Z
This tester measures the tensile or compressive strength of various samples
-
product
Transient Over-voltages Tester
SUG335
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
product
FOCL Reference Signal Modem
VCH-607
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
product
Digital 130AMP Battery/Alternator Tester
MD4780
For testing 6V and 12V batteries, charging systems, alternator diodes and starter. Industry leading 130 amp load .
-
product
DYNAMIC SIGNAL ANALYZERS
900 Series
The new SignalCalc 900 Series software makes the process of defining a test, making measurements, analyzing data and generating high-quality reports easier than ever before. All setup, project, test article, and customer information is saved along with measurement data in a database. Easily search for data from different test runs and test types for analysis and report generation.
-
product
Video Signal Processors
Products that apply signal processing to convert, reformat, or optimize incoming video signals.
-
product
Digital Battery Testers
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-02
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Cable Transmission Tester
SIGNALTEK CT
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
product
Lithium Battery Equalization Tester
LIFG
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
product
Peel Testers
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
product
Concrete Hardness Tester
W-M-250
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
product
Signaling Gateway Solutions
Service Providers are making the transition to 4G, and 5G is coming, but legacy connectivity for voice, SMS and IN applications still remains an absolute requirement. SS7 TDM interfaces must be maintained to meet the demand to interconnect different networks and multi-protocol solutions are required to connect divergent circuit and packet switching architectures. SS7 isn’t retrograde – it’s traditional. It’s still the most robust, high performance, and reliable signaling solution out there and it’s needed today more than ever.
-
-
product
PAT Testers Kits
Our PAT testing kits are designed to increase efficiency when testing. We have an excellent selection of PAT testing kits available. They are designed to help the way you work by creating efficiencies and help you get more from your PAT tester in the field. Our PAT testing kits are available with and without software so you can streamline your reporting process and provide a full and complete service to your customers.
-
product
Single Fiber Strength Tester
TB400C
TESTEX Testing Equipment Systems Ltd.
Single Fiber Strength Tester, suitable to test the tension strength and elongation of chemical fiber, cotton, wool, ramie, silk, glass fiber, fine metallic thread, etc.
-
product
4 Moving Probe Tester
L Series E4L6151
This is the latest EMMA series affordable model that offers low damage, high-speed and high-accuracy test. Max. Test Area 24 x 20" (610x510mm). Number of Probes 2 Front, 2 Rear. Min. Pad Pitch *1 0.007087" (180µm). Min. Pad Size *2 0.00314" (80µm).
-
product
Primary Current Injection Tester
SLQ
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
product
Signal Converters & Load Cell Signal Converter
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
product
Deadweight Testers
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
product
Torque Tester
CD-100M/10M
Ideal for daily inspection of electric screwdrivers. Use conventional joints. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. 3 times more durable than the conventional model, even with sudden high torque. disassemble the joint due to excessive unwinding .
