Signaling Testers
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Speaker/Receiver Unit Tester
BK2120A
Our new, upgraded BK2120A is a complete system for testing both acoustical features and rub & buzz in microspeakers, receivers and earphones or earbuds. It is just as fast and easy to use as our "Classic" BK2120A speaker tester, but because it connects with a LAN cable, you can use it with a notebook, as well as a PC. Its new modular design also makes maintenance more convenient and the redesigned BS1123 software is even easier to use and more versitile than the old version. You still get both graphical and numeric test data but with more display options than before. We still customize our machine to your special needs and of course you can still save your data to analyze later. Easier setup, improved design, more features, easier to use: we expect our new BK2120A to be even more popular than the original!
-
product
Automatic System Function Tester
3260
Chroma 3620 is an innovative system handler for high-volume multi-site IC testing at the system level.
-
product
Martindale Abrasion Tester
UI-FT19
Martindale Abrasion Tester is used to test pilling & abrasion resistance of textile fabric, leather and other materials by rub sample in all directions (a Lissajous figure) in wet or dry conditions.
-
product
10KV Withstand Voltage Tester
Shenzhen Chuangxin Instruments Co., Ltd.
10KV withstand voltage tester High voltage tester, Hipot Tester fast shipping high quality
-
product
110-125V AC Receptacle Tester
1933
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits.Detect faulty wiring in 3 wire receptacle.
-
product
Automatic Dielectric Tester
LD-LADT-A10
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
product
Water Vapour Permeability Tester
UI-FT16
Water Vapour Permeability Tester (WVP) is applied to test the water vapour permeability of all kinds of leather.
-
product
Opticle Encoder Tester
Endeavour
Evolusys Technologies Sdn. Bhd.
The Endeavour test system is a complete solution for testing optical digital and analog encoders for electrical and functional test with high accuracy and high speed. It provides high precision, research-grade electrical and functional testing and signal characterization suitable for encoder development. For quality assurance in encoder production, the Endeavour can be easily combined with a handling system for automated, high-end testing and qualification in the production of encoders.
-
product
IEPE Signal Conditioning Amplifiers
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
product
Cable Testers
AEMC's line of hand-held cable testers provides direct and simple push button operation. The testers indicate faults, cable length, common wiring faults and more. All models feature a large, blue electroluminescent backlit display.
-
product
Leather Softness Tester
TF115
TESTEX Testing Equipment Systems Ltd.
Leather Softness Tester, to determine the softness of leather and coated fabrics and other soft materials. Softness tester does not need samples to be cut from leather prior to testing.This enables a quality system to be set-up between supplier and customer whenever leather softness is a priority. Analogue and digital softness testers are available.
-
product
High Precision IR Tester
TH2684
Changzhou Tonghui Electronic Co., Ltd.
TH2684 High Precision IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR properties of electronic parts and components, dielectric materials, equipments, cables, etc. Large LCD and user friendly menu provide you easier operation.
-
product
Video Signal Generator
MSHG-600 Plus
MSHG-600Plus supports a exclusive HDMI 1.4a Signal and output signal to five(5) channels. It is also built-in CEC function according to current market request. *3D video Format Support *It can be On/Off Audio Return Channel with ARC switch separately.
-
product
DSE Wire Testers
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
product
Network Cable Tester
AVJoG
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
product
Electrical Safety Testers
A high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
product
Pull-Off Adhesion Tester
506
The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory.
-
product
CMT - Tester
VPC G12 interface - interchangeable fixturesQuick exchange of test applicationMinimum of equipment in the fixture - fixture only as contacting interfaceManual fixtures ATXFixture identification - automatic test program loadingConnection to external meas. instrumentsControled by SCADUS / LabViewSelftest of internal cards and connected instrumentsCentral test program, configuration and datalog files location possibility (server)Uninterruptible power supply for PC
-
product
Timing Signal Generator
OSA 5548C TSG
Our OSA 5548C Timing Signal Generator (TSG) is a scalable synchronization solution ranging anywhere from 20 unprotected outputs up to a thousand protected outputs by adding up to four expansion shelves to the core unit. Its ultra-compact footprint makes it ideal for telecom operators to provide scalable network synchronization in over-crowded exchanges. The OSA 5548C TSG’s distributed intelligence message passing system eliminates single points of failure and guarantees reliable uptime. Core unit and expansion shelves share the same modules, minimizing overall administrative complexity and enabling reduced homologation activity.
-
product
Conductive Footwear Tester
SLTM-1
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
product
Continuity Tester
4102
Peaceful Thriving Enterprise Co Ltd
This product is designed to measure the continuity of electric circuits and components. The measurement result will be indicated by LED and buzzer. The illumination is very helpful when technician is working in dark environment.
-
product
Voltage/Continuity Tester
VOT-52
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
-
product
Cable Tester
LW3310
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
product
Signal Conditioning
Various preamplifiers and signal converters extend the range of applications for Elsys data acquisition systems.
-
product
CABLE TESTER
MCT-7
Whirlwind Music Distributors, Inc.
This diagnostic cable tester has connectors for analyzing almost any type of cable combination. The convenient rotary switch allows testing of each conductor within the cable and can determine the internal wiring configuration. Tests NL4, 5 pin DIN, BNC, XLR, TRS, RCA and 3.5 mm types.
-
product
Network Tester
Shaanxi Aitelong Technology Co., Ltd
Devices that can be used to check network cables and network connections in the Ethernet.
-
product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Drop Tester
AccuDrop 160A
Model AD-160A is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
