Signaling Testers
-
Product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
RF Signal Generator
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Signal Switching
SMP/SMIP Series
-
VTI's SMIP™ signal switching series revolutionized the automated signal switching marketplace by providing a level of modularity, density, and performance for the VXIbus platform that was unprecedented.
-
Product
AMIDA 3KS Tester
-
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
-
-
Product
Fan Assembly Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing the performance of DC brushed and brushless motor, AC radiator, heater fan assemblies.
-
Product
Large Range Resistivity Tester
HS-SFRT
-
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
Product
Dynamic Signal Analysis
-
m+p Analyzer is a fully integrated solution for dynamic signal measurement, analysis and advanced reporting of all noise and vibration, acoustics and general dynamic signal applications. Comprehensive time and frequency analysis is available with both online and offline data processing. Complete with advanced application wizards the m+p dynamic signal analyzer makes light work of gathering data, displaying results, performing specialized analysis and generating customer ready reports – all within one user interface. m+p Analyzer is designed for noise and vibration applications in the field and in the lab.
-
Product
Density Tester
LD-LDMT-A10
-
LabodamLD-LDMT-A10density tester is simple and compact. The control box adopts humanized design and the control switch adopts light-touch mode. The instrument is designed and made as per ASTM D1298 “Test Methods for Density of Petroleum and Liquid Petroleum Products (Densimeter Methods).
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
2-way Radio Signaling Test Software
Tone Generator
-
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
Product
Advanced Diagnostic Trailer Tester
Alpha MUTT
-
Innovative Products of America
The Alpha MUTT® takes IPA's industry leading Super MUTT® platform, and adds the ability to instantly save, store, and share inspection reports. It gives customers peace of mind with complete accountability through detailed reports and gives technicians a better, faster way to enter and track report results. The mobile, durable Alpha MUTT® tests trailer lights, air brakes, and ABS systems via a Bluetooth-connected tablet with IPA's custom diagnostic software suite.
-
Product
Stationary Battery Comprehensive Tester
SAT-AG Series
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AG Series Stationary Battery Comprehensive Tester is a kind of product introduced according to the market demand, which integrates the two major functions: on-line monitoring and capacity check test, with higher integration and better functions.SAT-AG is specifically designed for the maintenance of the lead-acid battery discharge in the electricity and telecommunication sector. It is a new high-tech intelligent product that provides safe, reliable and convenient constant testing equipment for the DC system(Direct current system) users.
-
Product
Turns Ratio and Phase Tester
SS310
-
Turn ratio meter is a reliable test instrument used for product inspection and sample analysis in the manufacture of transformer, radio and TV set or relative scientific research units.
-
Product
Smoke Detector Tester
Solo 365
-
The fire industry’s most popular range of detector test equipment is about to get even better. Solo, the test equipment used world-wide to functionally test fire detectors has a new tester in its range – Solo 365. This exciting innovation provides fire safety professionals with an array of stand-out features which make for faster, simpler and cleaner functional testing of smoke detectors. Key features include automatic generation of smoke which ensures only the amount of smoke needed to activate the detector is produced – minimizing smoke wastage and eliminating the risk of detector contamination. In addition, Solo 365 is light in weight and has a slim-line design which allows easy access into tight spaces – making it possible to test detectors which are hard to access with other portable testers. In response to market feedback, Solo 365 features an LED torch which automatically illuminates when light levels drop, making for easy detector alignment and testing in dark environments. Smoke is generated via newly designed smoke cartridges which fit neatly into the rear of the tester. With no reliance on pressurised aerosol cans, the cartridges can be easily shipped and stored and are unaffected by new regulations, set for 2018, which will affect availability of some pressurised smoke aerosols.
-
Product
Torsion Tester
-
This apparatus is one excellent integration of measurement units. It’s mainly for the R & D department to study users’ body output in riding their designed bicycles.
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
Video Signal Distributor
MSHM-305A/310A
-
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
Product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
Signal Analyzer
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
Product
Flexure Tester
G201A32-33
-
To determine whether metallic wires or materials used for stiffening or retention of form in child-related products can be easily bent or broken.
-
Product
Brinell Hardness Tester
-
Beijing TIME High Technology Ltd.
Measures a material's resistance to indentation by pressing a hardened steel or carbide ball into its surface with a specific force.
-
Product
Signal Converters For Computer-aided Measurement
EIB 700 and IK 220 series
-
*Ideal as evaluation unit for high encoder signal resolutions and rapid measurement*EIB 700: connection of multiple evaluation units with Ethernet transmission and, for example, wireless LAN transmission paths*EIB 700: connection of up to four HEIDENHAIN encoders*IK 220: PCI counter card*IK 220: connection of up to two HEIDENHAIN encoders
-
Product
De-Energized Tester
ALL-TEST PRO 34
-
The ALL-TEST PRO 34™ uses our proven, patented technology to look beyond vibration, temperature, and ultrasound test methods- giving you instant answers on your motor’s health. It represents the 7th generation in product innovation that ensures the reliability of motors in the field and helps to maximize the productivity of maintenance teams everywhere.
-
Product
Sharp Edge Tester
SE400
-
The Sharp Edge Tester is used for determining the sharpness of edges of electrical equipment and other consumer products. A special tape is mounted on a spring loaded arm and dragged over the sharp edge. The tape is then inspected for damages.
-
Product
Network Cable Tester
PA-40
-
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Single Channel Tester
MS 3600I
-
The Integrated Flight Control Computer (IFCC) is the central control computer for the RPFA. IFCC consists of flight control computer, Air Data Computer, Aircraft Encoder Decoder unit. The Single Channel Tester is the automatic test equipment to test the IFCC. SCT shall be used to perform the hardware ATP of IFCC.
-
Product
Hose Continuity Tester
OhmGuard
-
The OhmGuard hose continuity tester is designed to test hoses used on vacuum trucks and tanker trucks prior to the transfer of flammable or combustible products
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
Signal Amplifier
9200
Amplifier
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
