Open Circuit
-
Product
Insulation & Multifunction Tester (LCD Display)
1152 MF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Check-Point Circuit Tester
21000
-
Most widely used automotive circuit tester. Quickly checks all 6 and 12 volt systems. Use with power on. 48" ground wire. Use to locate shorts, grounds and open circuits.
-
Product
Ground-Fault Location Products for Ungrounded Systems
-
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
Product
Insulation & Multifunction Tester (LCD Display)
1153 AI
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
Simulator
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Solar Array Simulator
62000H-S series
Simulator
The latest programmable solar array simulator power supply 62000H-S Series released by Chroma provide simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000H-S provides an industry leading power density in a small 3U high package. The solar array simulator is highly stable and has a fast transient response design, which are both advantageous to MPPT performance evaluation on PV inverter devices. The 62000H-S Series have many unique advantages including high speed & precision digitizing measurement circuits with a 100kHz A/D, 25kHz D/A controlled I-V curve and a digital filter mechanism. It can simulate an I-V curve accurately and response the mains ripple effect from the PV inverter. In addition, the built-in EN50530/Sandia SAS I-V model in the standalone unit can easily program the Voc, Isc, Vmp, and Imp parameters for I-V curve simulation, without a PC controller.
-
Product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY 8125
-
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm
85032F
-
The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.
-
Product
LAN Cable Multifunction Tester
TCT-2690PRO
-
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
Product
Cable Testers
-
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Product
PXI Millivolt Thermocouple Simulators
Series 41-760
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
Product
PROBE MICROPHONE ICP
377B26
-
Open Circuit Sensitivity (at 250 Hz)Frequency Range (+2.2/-4.9 dB)2 to 20000 HzLower Limiting Frequency (-3 dB)Inherent Noise<45 dB(A) re 20 Pa Dynamic Range(3% Distortion Limit)EnvironmentalTemperature Range (Operating)-40 to +158 F-40 to +70 C[5]
-
Product
Heavy Duty Circuit Tester
27000
-
Designed for testing electrical circuits and locating shorts, grounds, and open circuits. Electrical circuit tester available for checking 6V and 12V systems. Heavy duty battery clip .
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-252-111
Programmable Resistor Modules
The 40-252-111 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
Programmable Resistor Modules
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Multifunction Tester(Insulation & Earth restistance)(LCD Display)
9000 MF
-
Standard Electric Works Co., Ltd
● 9000 MF multi-function tester is a combination of insulation tester and earth resistance tester● Insulation output voltage : 50V, 100V, 125V, 250V, 500V, 1000V● 1mA test current on insulation test at nominal voltage● Auto-detection AC/DC voltmeter● Continuity short-circuit current > 200mA● Continuity open circuit voltage > 4.1V● PI and DAR indication● Maximum insulation range 8GΩ ( 8000MΩ ) at 1000V● Auto ranging on all insulation ranges● Continuity range : 2000Ω and 200.0Ω (auto ranging )● Auto power off● Test frequency of earth resistance measurement : 128 Hz● Earth resistance measurement for 3 ranges : 40Ω / 400Ω / 4kΩ● Earth resistance resolution : 0.01Ω / 0.1Ω / 1Ω● Earth voltage measurement : 400V● Auto-null ( Relative mode ) function● Backlight function● Low battery
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
Simulator
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Standard Helmholtz Coils
-
Helmholtz Coils are ideal for the measurement of Rare Earth (Samarium Cobalt, Neodymium) and Hard Ferrite permanent magnet materials (materials which exhibit a relative straight line demagnetization). Our standard Helmholtz Coils are for use with fluxmeters. The Helmholtz Coil measures the magnet sample as a single magnetic moment provided that the longest dimension of the magnet sample is less than one-third (1/3) the diameter of the coil system. By definition, the magnetic moment per unit volume is the intrinsic magnetization of the sample. With our calibrated Helmholtz Coil and Integrated Fluxmeter – and given the volume of the permanent magnet sample – the intrinsic open circuit operating B (Bdi) can be measured.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
C/I Tracers
Circuit Seeker Kit
-
*Advanced patented non-directional sensing technology*Superior sensitivity and functionality providing for accurate tracing & locating*Ergonomic receiver with information-rich full-color graphical LCD*Graphics and audible signal provide quick and easy way to understand tracing feedback*Traces concealed wiring, locates junction boxes, and finds breakers for live or open circuits
-
Product
Emergency/Panic Button
ENVIROMUX-EBS
-
Sends activation signal when button is pressed. For normally closed or normally open circuit connections. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH: 1.7x2.9x4.6 in (43x74x117 mm). Regulatory approvals: RoHS.
-
Product
Electrical Test Tool
-
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Precision Condenser Microphone
377C10
-
Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%
