Open Circuit
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
PXI RTD Simulator Module, 4 Channel, PT500
40-263-502
Simulator
The 40-263-502 is a 4-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Solid State Relay Products
-
DARE Electronics? solid state relays incorporate advanced microelectronic hybrid technology and are available from low level to 50 amps. Solid state relays have distinct advantages over electro-mechanical devices including: no contact bounce, arcing or flashing; immunity to contact contamination and oxide formation in dry or normally open circuits; and immunity to shock and vibration thus preventing unwanted contact closures
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 122Ω
40-252-012
Programmable Resistor Modules
The 40-252-012 is a programmable resistor module with 4 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Insulation & Multifunction Tester (LCD Display)
1155 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Thermal/Multi-Function Data Logger
51101
-
Chroma Systems Solutions, Inc.
Models with 1, 8, and 64 channels on-line data recording. Multi-sets linked to a PC for hundreds of channels are doableSupports B, E, J, K, N, R, S, and T type thermal couples with ITS-90 defined temperature rangeIndividual channel cold junction compensation withTemperature resolution up to 0.01℃, error down to (0.01% of reading+0.3℃)Voltage full range ±480VDC, ±10VDC; resolution 1mV, 10uV; error down to (0.1% of reading+1mV), (0.015% of reading+100uV)1000VDC channel to channel isolation, full protection for testing points with charge and guarantee for accurate measurementsThermal couple open circuit detectionPC-based operation with powerful software for recording and analyzing data1 and 8 channel models are USB powered. No battery or external power supply is required
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Precision Condenser Microphone
2575
-
Performance:Nominal Microphone Diameter1"1" Frequency Response: Characteristic (at 0 incidence) Random IncidenceRandom Incidence Open Circuit Sensitivity: 45 mV/Pa Resonant Frequency (90 Phase Shift)8000 Hz8000 Hz[1] Inherent Noise<10 dB(A) re 20 Pa<10 dBTemperature Range (Operating)TBD FTBD C Humidity Coefficient of Sensitivity (0 to 95%, non-condensing)0.001 dB/%RH
-
Product
Precision Condenser Microphone
377C10
-
Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 122Ω
40-253-112
Programmable Resistor Modules
The 40-253-112 is a programmable resistor module with 1 channel which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Rack Mount Cable Tester
AudioJog Rack
-
There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections.
-
Product
PXI RTD Simulator Module, 8 Channel, PT1000
40-263-403
Simulator
The 40-263-403 is an 8-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Lan Cable Tester
185 LCT
-
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
PXI RTD Simulator Module, 16 Channel, PT500
40-263-202
Simulator
The 40-263-202 is a 16-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Multifunction Tester(Insulation & Earth restistance)(LCD Display)
9000 MF
-
Standard Electric Works Co., Ltd
● 9000 MF multi-function tester is a combination of insulation tester and earth resistance tester● Insulation output voltage : 50V, 100V, 125V, 250V, 500V, 1000V● 1mA test current on insulation test at nominal voltage● Auto-detection AC/DC voltmeter● Continuity short-circuit current > 200mA● Continuity open circuit voltage > 4.1V● PI and DAR indication● Maximum insulation range 8GΩ ( 8000MΩ ) at 1000V● Auto ranging on all insulation ranges● Continuity range : 2000Ω and 200.0Ω (auto ranging )● Auto power off● Test frequency of earth resistance measurement : 128 Hz● Earth resistance measurement for 3 ranges : 40Ω / 400Ω / 4kΩ● Earth resistance resolution : 0.01Ω / 0.1Ω / 1Ω● Earth voltage measurement : 400V● Auto-null ( Relative mode ) function● Backlight function● Low battery
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Cable Testers
-
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Product
PXI RTD Simulator Module, 20 Channel, PT1000
40-263-103
Simulator
The 40-263-103 is a 20-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Self-Discharge Measurement Solutions
-
Directly measure self-discharge current in 1-2 hours instead of monitoring cell open circuit voltage over weeks or months. Quickly measure & analyze self-discharge current during cell design and evaluation. Reduce design cycle time and get to market faster. Rapidly discern good vs. bad cell self-discharge performance in manufacturing. Dramatically decrease work-in-process inventory.
-
Product
Single Phase 2 Circuit Energy Meter Test Bench Type KP-S1000-B
-
Bofa Instrument & Equipment Co., Ltd
Single phase 2-circuit energy meter test bench type KP-S1000-B, is a new generation, high precision energy meter calibration equipment. It is especially designed for testing 2-circuit energy meter (shunt circuit and CT circuit), open or closed test link (I-P link) both. It is an ideal testing equipment for mass production of 2-circuit energy meter in meter factory. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
PXI/PXIe Digital To Analog Module - 4 Channel
43-770-001
Digital / Analog Converter
The 41-770-001 (PXI) and 43-770-001 (PXIe) have four Digital to Analogue Conversion channels in a single PXI/PXIe slot. Each channel is fully isolated and able to supply a programmable voltage or programmable current output. The outputs can work in one of several modes of operation: ±1 V, ±2 V, ±5 V, ±10 V, ±20 V, 0-40 V, ±5 mA, ±10 mA, ±20 mA. Each channel of the 41/43-770 module is able to simulate the open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-253-011
Programmable Resistor Modules
The 40-253-011 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Standard Helmholtz Coils
-
Helmholtz Coils are ideal for the measurement of Rare Earth (Samarium Cobalt, Neodymium) and Hard Ferrite permanent magnet materials (materials which exhibit a relative straight line demagnetization). Our standard Helmholtz Coils are for use with fluxmeters. The Helmholtz Coil measures the magnet sample as a single magnetic moment provided that the longest dimension of the magnet sample is less than one-third (1/3) the diameter of the coil system. By definition, the magnetic moment per unit volume is the intrinsic magnetization of the sample. With our calibrated Helmholtz Coil and Integrated Fluxmeter – and given the volume of the permanent magnet sample – the intrinsic open circuit operating B (Bdi) can be measured.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PXI RTD Simulator Module, 24 Channel, PT1000
40-263-003
Simulator
The 40-263-003 is a 24-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
Simulator
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
