Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
product
6GHz RF Signal Generator
TGR6000
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
PCI and PCI-X Bus Analyzer / Exerciser
PCI850
The PCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Photon Counting Cameras
Photek photon-counting camera systems are unique as they provide the ability to capture and integrate an image in real time. These systems are ideal for extremely low photon emission applications such as bio-luminescence, chemi-luminescence and weak fluorescence. The ability to accurately analyze transient events is a key feature of this product. The length of time that the image can be integrated is limited only by disc space, and allows the user to fully capture real-time events. X, Y and time co-ordinates for post acquisition analysis is also recorded. X-ray and vacuum imaging camera options are also available.
-
product
AATCC Wrinkle Recovery Tester
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric’s ability to recover after wrinkling under a pre-determined load for a set period of time.
-
product
Extremely Accelerated Stress Test Chambers
The extremely accelerated stress environment is defined by high temperature, high humidity and high pressure. WEIBER provides humidity resistance evaluation test for electronics components through customized Extremely Accelerated Stress Test Chamber. This chamber provides high performance test in minimal amount of time according to international IEC 60068-2-66 standard. This chamber also known as Accelerated Stress Test Chamber, Halt and Hass Test Chamber, Halt Test Chamber and Hass Test Chamber.This chamber reduces the time taken for humidity testing in electronic components. 2 types of tests saturated and unsaturated extremely accelerated stress test can be performed. In saturated test the temperature is maintained at 1210C at 100%RH, and for unsaturated temperature of 110, 120, 1300C is maintained at 85%RH. Normally for electronic components unsaturated type test is done.
-
product
SparkFun Spectral Sensor Breakout
AS7263 NIR (Qwiic)
The SparkFun AS7263 Near Infrared (NIR) Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7263 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
product
microRSP
M300
The semi-automatic microRSP-M300 by CAPRES A/S is a unique R&D tool for sheet resistance measurements of conductive surfaces in micro scale. Like the automatic microRSP by CAPRES A/S the semi-automatic microRSP makes use of the micro 4 point probe characterised by having a probe pitch of 1000 times smaller pin spacing/pitch than that of conventional probes.
-
product
RF Subsystems
Using the Ideal Switch to develop RF subsystems enables substantial performance and reliability improvements. At the same time their size and weight decrease by several orders of magnitude.
-
product
Three-Phase Relay Protection Tester
GDJB-PC
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.GDJB-PC Universal Secondary Injection Relay Test Set is applied to test the relay unit in relay protection system. 2.At the same time GDJB-PC Universal Secondary Injection Relay Test Set could be considered as a universal three phase AC/DC voltage source or current source. 3.It can work alone or connected to computer, inside the relay controller there are new speed digital signal mini PC and real DAC (Digital-to-Analog Converter) template with new high fidelity and high power, the machine has large panel screen and rotating mouse. It is small in volume, high precision.
-
product
GeoSwath Module
The GeoSwath Plus Sonar Module contains a wide-swath bathymetric sonar suitable for a range of survey and inspection tasks. The GeoSwath Plus is a 500kHz interferometric sonar, or phase detecting bathymetric sonar (PDBS) from Kongsberg GeoAcoustics. Boat-mounted GeoSwath sonars are used worldwide for high accuracy surveys including port and harbour navigation and environmental mapping: the Gavia’s GeoSwath module makes this capability available in a commercial AUV. The GeoSwath Plus offers: wide swath coverage of up to 12 times the AUV altitude when near the seabed; integrated bathymetry with simultaneous true digital side scan; high depth resolution suitable for IHO survey standards; as well as the accuracy and repeatability of a boat-mount hydrographic survey system. Like most of the survey-grade sensors on the Gavia AUV, the GeoSwath data is time-synchronised with the AUV master clock using the vehicle PPS/ZDA system. Benefits of the GeoSwath AUV module include ease of deployment, ease of use, reducing survey time, and the ability to take a 500kHz high-resolution sonar down to targets in 1000m of water. The GeoSwath Plus post-processing software (provided as standard with the system) allows a user to inspect and process the data, create and inspect digital terrain models, and create basic sonar mosaics. Several other commercial post-processing software packages are also available, please ask for details. Note that for best results the GeoSwath Module should be deployed with a direct-reading sound velocity sensor (option) in the Control Module, and one of the high-accuracy INS/DVL Navigation Modules for motion sensing.
-
product
Multibeam Echosounder - Shallow Water
SeaBat T50-P
The SeaBat T50-P is the new addition to the leading SeaBat T-series product range engineered from the ground up to evolve with your business. Combined with the Portable Sonar Processor the SeaBat T50-P provides unprecedented survey data, providing faster operational surveys and reduced processing time.
-
product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
product
Digital Mass Flow Controller and Meter
300 Vue Series Digital Flow Meter
The 300 Vue is our newest series of digital gas thermal mass flow instruments which provide accurate, fast and convenient gas measurement and control. The color touchscreen display allows for local adjustments and monitoring of gas flow. Powerful and intuitive menus enable control of the gas flow in many ways. The instrument can be installed and operating in seconds. Flexible custom flow instruments without the custom price or lead time.
-
product
Automated Optical Switch - MATRIQ
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
Single Channel High Voltage Linear Amplifier
F10A
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Mixed Signal Oscilloscope - 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154A
1.5 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
product
Advanced Multicore Software Development Kit
M*SDK
The focus of the Imperas products is to save engineering time in the development of embedded software, primarily achieved by making the engineering process significantly more efficient through the use of high-performance simulation and automated, powerful tooling.
-
product
PC-Based Bus Platform
PXI 3U
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
product
*C Series CAN Interface Module
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Structural Test ICP® Accelerometers
Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimized, reducing time consuming data verification or re-test. The Series 333 ICP® accelerometers, and their accessories, are designed to address the needs of multi-point modal and structural test measurement applications. This equipment was developed in conjunction with the world renowned University of Cincinnati Structural Dynamics Research Laboratory and proven in real-world testing situations. The PCB 333 Series accelerometers delivers rapid system setup, reduces human documentation errors, maintains calibration data of each sensor, allows for “Plug-and-Play” installation, reduces overall test time lowering project test costs.
-
product
OpenSpace® QuantumDRA
Kratos Defense & Security Solutions, Inc.
The OpenSpace® quantumDRA is a virtualized product that archives and passes telemetry data at a high rate to disk. It addresses the challenge of managing large amounts of data produced by a satellite with limited connection time to antenna. OpenSpace quantumDRA stores and forwards data to the antenna for future use by the satellite operations center.
-
product
Real Time Monitoring Of Windows Server
GSX for Windows Server
Monitor and troubleshoot operating systems and related applications from a single dashboard. Windows servers and services are fueling mission-critical applications, so having visibility into the status of their health and usage is essential. By continuously testing the availability and performance of the Windows server and its applications, GSX enables proactive management of the IT environment. End-to-end monitoring improves the end-user experience, reduces mean-time-to-repair, and helps administrators to prevent issues before they happen.
-
product
Fanout Buffers
Fanout Buffers are able to create multiple copies of input signal at their output and distribute them amaong several loads while achieving fast rise/fall time and low jitter. Input and output interfaces are CML and output voltage swing can be adjusted externally.
-
product
Call Generation
Emutel SIP Harmony
SIP Harmony has strong Call Generation capabilities. Using the SIP | Harmony ''Composer'' application, scripts can be quickly created to generate high volumes of calls. Once calls are established they can be cleared down straight away or held active for any period of time to simulate different call lengths. The SIP | Harmony is also capable of terminating calls, so complete wraparound testing of any piece of equipment can be carried out.
-
product
2-18GHz Instantaneous Frequency Measurement Unit
DR058-F2
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Rapid Evaporative Ionization Mass Spectrometry
REIMS
The innovative iKnife hand-held sampling device produces information-rich vapor directly from the surface of the sample, which when analyzed by a time of flight (Tof) MS, provides analysts with an accurate molecular profile in seconds.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-02
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
SparkFun GNSS Timing Breakout
ZED-F9T (Qwiic)
The SparkFun GNSS Timing Breakout offers a unique entry into SparkFun's geospatial catalog featuring the ZED-F9T GNSS receiver from u-blox. The ZED-F9T provides up to five nanosecond timing accuracy under clear skies with no external GNSS correction making it perfect for applications where timing accuracy is imperative. Need an extremely accurate time reference to maximize the efficiency of your IoT network of 5G devices? The ZED-F9T GNSS Timing Breakout could be the perfect solution.
