Plugs
A male connector.
-
product
EZ-Tach Digital Automotive Tachometer
325
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
-
product
Miller 400A
44500
Rugged, lightweight case - safe to use on wet ground. Weatherproof, even with lid removed - IP67 rating for dust and water intrusion. Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations. Resistance measurement range from 0.01Ω to 1.1MΩ . Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency). Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
product
GOOSEMeter One IEC 61850 Message Monitor
IEC-61850
The GOOSEMeter One is an easy to use, hand held instrument that will instantaneously display the ongoing GOOSE traffic when plugged into an IEC-61850 substation’s control bus LAN
-
product
- 10Base-T to Multimode Fiber Optic Transceiver
Model 373
FEATURES: Extend Lan's over 1 mile; Full Duplex Plug and Play - no software; Uses industry standard fiber optic cables; Impervious to lightning and surges; Total electrical isolation; 10Base FL compatible. Now you can break the distance barrier of Ethernet based Local Area Networks and achieve total system safety from electrical interference and surges.
-
product
Shield
Arduino Ethernet Shield 2
The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board (not included)
-
product
Audio Test Tone Generator
Tone Plug
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
product
Dual 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-012
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
Plug in Meters
make accurately measuring the power (watts) and energy (kilowatt-hours) consumption of 117vac plug in appliances a snap!
-
product
Thermocouple (K-Type) And Temperature Probe Adapter
U1186A
Consists of a K-type thermocouple bead and a mini connector to dual banana plugs.
-
product
PCIe
SFF 8639 Gen4 (U.2)
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
product
Amplifier Systems Band Specific
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
PXI/PXIe Power Relay Module, 16xSPDT
40-158-003-HI
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
product
AC Line Separators
ALS-2
Standard Electric Works Co., Ltd
● x10 Model allows for more accurate measurements of low amperage devices.● Direct reading x1 mode.● 4mm Voltmeter input jacks.● Intergrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
USB-C® – USB 2.0 C Receptacle to A Plug
AUT17032-CRAP
This fixture is designed for USB-C 2.0 Plug and USB-A products.
-
product
SoM Modules
Sundance Multiprocessor Technology Ltd.
A System on Module is a small plug on device that has a collection of integrated electronics, like a CPU and/or FPGA and is self-contained and only requires a power source to work. A SoM is typically integrated onto a carrier module with ‘Custom’ I/O to enable interface to Real-World signals.
-
product
16-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2351A
The U2351A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
product
Software
SSI-TRES
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
product
Power Monitor
ACScout-NETBB
The ACScout-NETBB adds a battery backup to everything ACScout NET already does. Now your monitored power data is logged and backed up using the battery. The ACScout is still a highly reliable, easy-to-use AC power monitor that plugs into an electrical outlet. It records surges, outages and variations in voltage and frequency as well as ambient temperature and can now backup all data logged with help of a new battery.
-
product
Bus Analyzer / Exerciser
VME850P0
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
product
AC/DC Clamp Meter
3902 CL
Standard Electric Works Co., Ltd
● 2000 - count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ Capacitor measurement ◎ Frequency counter.● Range change function.● Data Hold function freezes the reading.● Continuity check.● Diode measurement.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
1U-4U SlimBox For CompactPCI
1U to 4U rack-mounted enclosure with 482.6 mm (19") mounting brackets (may be offset approximately 100 mm to the rear). Two backplane slots can fit in each 1U of chassis height (standard 0.8” pitch) with rear plug I/O options. Enclosure cooling from left to right with EMC and ESDcompatible configuration. Optional: Hot swap-compatible power supply units with current splitting for redundancy operation (2U). Conforms to IEEE 1101.1/10/11,
-
-
product
3 Digit LCD Voltmeter
V 1
The V 1 is a very low cost 3 digit LCD voltmeter with 6.3mm (0.25") digit height, intended for high volume OEM applications. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two SIL sockets or can be panel mounted using the bezel provided. Connection to the meter is via two rows of 4 pins.
-
product
NI-9970, 2-Position, Spring Terminal Connector Plug, 3.5 mm Pitch (Qty 4)
787005-01
2-Position, Spring Terminal Connector Plug, 3.5 mm Pitch (Qty 4)
-
product
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 7-Pin DIN and 4 Banana Plugs
540078010111
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 7-Pin DIN and 4 Banana Plugs
-
product
PCB Test System
Circuit Wizard - CW409
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
product
SSD Test Systems
MPT3000ES / MPT3000ES2
Using the same high-performance electronics and powerful software as all products in the MPT3000 family, the MPT3000ES and MPT3000ES2 engineering stations feature a small footprint configured to test up to eight SSDs in parallel. The system's small size and ability to plug into a standard AC outlet enable users to conduct program development and interactive device debugging in either office or lab settings.
