Plugs
A male connector.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
Inertial Measurement Units
IMU
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
product
Coil-On-Plug Spark Tester
20700
Provides an Easy Way to Check Ignition Systems with Coil-On Plugs. Applications Include Ford, Chrysler, Mitsubishi, Nissan and More.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Conductive Footwear Tester
SLTM-1
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
product
Universal CMM Software Module
Verisurf CMM
Plug and play CMM communication for Hexagon Dea, Leitz, Mitutoyo, Wenzel, Pantec, Nikon, LK or Zeiss™️ machine controllers, as well as Renishaw, Tesa, Hexagon Leitz or Zeiss™️ head controllers.Optional support for scanning probes and error mapping compensation for geometric, volumetric, orientation, positioning and kinematic errors in the CMM structure that affects accuracy.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Alle Schaltnetzteile
PeakTech Prüf- und Messtechnik GmbH
A DC switching power supply, which convinces with its high performance and best price / performance ratio. The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs.
-
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector, With Interlock
42-153-004-HI
The 40/42-153-004-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
product
Cable Assembly, Receiver, 36", VTAC, 2 RJ45 Plugs
540224010267
Cable Assembly, Receiver, 36", VTAC, 2 RJ45 Plugs
-
product
Pole Plug Tester
SAE 7
When there’s no time to waste the SAE 7-Pole Plug Tester provides a fast, easy way to isolate lighting problems to the tractor or trailer. Use it to test the output of SAE 7-pole tractor light cords, while connected to the tractor or to your Square Wheel Industries Trailer tester.
-
product
Gas Flow Sensors
ESRF-ESF Sensor
ESRF-ESF is one of the few gas flow sensors featuring bidirectional gas flow sensing of up to ±300 ln/min with a total error band of < 1.25% RD. ESRF-ESF gas flow sensors provide calibrated and temperature compensated output on an SPI, I2C bus or analog output making them plug & play for direct interfacing to low voltage MCUs and systems. The user is provided with a multitude of interface and output options so that the right sensor configuration can be selected based on the specific requirements for each application.
-
product
Torque Sensors
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
product
SHV Connectors
Pasternack SHV connectors category has several part numbers, most are RoHS and REACH compliant. SHV connector series in this category will terminate to coax or terminal. These SHV connectors are built to precise microwave and RF industry specifications. SHV connector items are built in jack or plug gender with 50 Ohm impedance. Connectors in SHV series are available in bulkhead, 4 hole panel or mountless options. These SHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with other over 40,000 RF, microwave and millimeter wave Pasternack products, this SHV connector series is in-stock. Not just are they in stock, but these radio frequency connectors will ship the same day as they are purchased.
-
product
Socket Outlet Torque Test Device
CX-LJ
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.
-
product
USB-to-Serial Cable Converter
This cable is the solution for users who want to communicate with GE Multilin IEDs via PCs that have USB communication ports. Using this cable is quick and easy. Simply install the cable driver on your PC, plug in the cable and you are ready to communicate.
-
product
HD Color Bar Generator
CBG830
The CBG830 color bar and test signal generators will produce a quality, high definition full field color bar signal compatible with the digital HDMI and DVI-D interfaces. The CBG830 is designed to provide an accurate and affordable signal source for easy testing of displays, cables and systems.The CBG830 will generate a full field color bar signal with eight vertical bars, white through black. This signal is available in a variety of resolutions and refresh rates. TheCBG830 will usually fit in a toolbox with ease and even fit into a pocket. There is also a rack mount kit available as well. Power is provided by a regulated 5VDC source and a small wall plug power module is included with the packaged CBG830 but not with board level products. The CBG830 will have a switch array to select the video standard.
-
product
Test Block & Plug Systems
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
product
Tow Doctor™ Trailer Side Test Unit
50928
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a trailer has been wired properly and all functions are working. Plug the Tow Doctor™ into the trailer connector and the power cord into a battery source and cycle through the trailer lighting functions. Includes 7 Blade, 6 Round and 4 Flat test connectors and durable carrying case.
-
product
Cable Assembly, Receiver, Mini Coax, 36", 3 BNC Plugs and 2 SMB Plugs
540059010207
Cable Assembly, Receiver, Mini Coax, 36", 3 BNC Plugs and 2 SMB Plugs
-
product
6-12V Duality High And Low Voltage Trouble Shooter
1669
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems, test for circuit and spark plug.1. Check spark plug on secondary or high voltage. 2. Use as a continuity tester to check on low voltage circuits.
-
product
Self-Cooling Condensor
EcoChyll X1
You can think of the EcoChyll X1 as a chiller with no tank, no coolant liquid, and which achieves its setpoint temperature in just one minute. It has a built-in condenser, connects to any brand of benchtop rotary evaporator, and has a footprint under one square foot.Want more? The EcoChyll X1 involves less tubing and fewer opportunities for leaks.Still want more? The EcoChyll X1 uses about one quarter of the electricity of a recirculating chiller with a similar cooling capacity.The EcoChyll has virtually no maintenance or setup requirements. Connect it to your existing rotary evaporator, plug it in, turn it on, and it’s ready to go.Ecodyst has pioneered a smart self-cooling technology with no consumables as compared with traditional rotary evaporators. Upgrade your rotary evaporator with EcoChyll X1 and immediately begin to benefit from the many advantages it offers.
-
product
General Purpose Lab Oven
REXMED ROV-150
MOD. ROV-150, AC 110/230V, Plug type: , General purpose lab oven, dry air / hot air sterilizer, HS CODE: 841780, UNCCS CODE: 447483, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~250˚C, Stability at 37˚C: ±0.2˚C, Uniformity at 150˚C: ±1.5˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 700W X 2pcs, Chamber: L50 X W50 X H60cm, Capacity: 150L, chamber with key lock, W/S: shelf X 2pcs
-
product
Three-axis Hall Magnetometer
THM1176
The THM1176 family combines the performance of a professional Hall instrument with the usability of a consumer USB device. Its range goes from the µT to 14 T, DC to 1 kHz, with ±1% accuracy. It simultaneously measures all three axes of the magnetic field, so you get a true field strength reading no matter how you hold the probe. The entire instrument has been reduced to a cable with a few fat spots, which can plug directly into your PC or into a battery-powered handheld computer. The result is the most compact, lightweight, low-power, go-anywhere and measure-anything magnetometer in the world. Teslameter Gaussmeter 3-axis
-
product
Cable Assembly, Receiver, Micro Coax, 36", 10 SMB Plugs
540092010247
Cable Assembly, Receiver, Micro Coax, 36", 10 SMB Plugs.
-
product
CoreAFM - the best value research AFM
CoreAFM
The fusion of a modern flexure-guided scanner, XYZ sample stage, camera, active vibration isolation table, and acoustic shielding in a single all-in-one unit results in a complete AFM system with an unparalleled compact footprint. The system comes with a fully digital 24-bit controller developed specifically for the CoreAFM scanhead. All the essential functions of modern AFM are integral components of the CoreAFM system; all you need to do to take the CoreAFM into operation is connect the controller, and plug in power and USB.State of the art electronics with 24-bit ADC and DAC ensure high-resolution XYZ driving of the 100×100×12 µm scanner and allow for low-noise force detection limited only by the cantilever. Thirty-two standard and optional modes with fully compatible add-ons make the CoreAFM the tool of choice for applications ranging from materials research to life science and electrochemistry. Starting from the basic CoreAFM system, its functionality can be seamlessly extended
-
product
SparkFun Analog MEMS Microphone Breakout
ICS-40180
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.
-
product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors, With Interlock
42-153-002-HI
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
