Plugs
A male connector.
-
product
Robotic Probing of Circuit Cards
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
product
6 Position Plug Socket Switch Life Tester
CZKS-6
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances. The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provide some clamp, it can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
product
MCX Connectors
Pasternack MCX connector category includes dozens of part numbers, most of which are RoHS and REACH compliant. MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our MCX connectors are built to precise RF and microwave industry specifications. MCX connector items are built in jack or plug gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. Connectors in the MCX series are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These MCX connector designs include crimp/solder or solder attachment methods. We offer MCX connectors with standard or high performance levels built with brass or stainless steel bodies. As with our other over 40,000 RF. microwave and millimeter wave products at Pasternack, this MCX connector series is in-stock. Not only in stock, but these coaxial connectors will ship the same day as they are purchased.
-
product
VXI Plug & Play Adapter Plate for Racal Instruments 9U Chassis
310113272
VXI Plug & Play Plate is used with the Single Tier VXI Receiver (Part # 310 104 127) to mount the Receiver to the VXI Chassis. Flanges must be purchased from the manufacturer.
-
product
18 Pc. Micro 64 Test Connector Kit
147
Test connector kit featuring a variety of terminal adapter sets which enable connection to Micro64 terminals - primarily found on GM vehicles and some EU/Asian/Domestic vehicles. Adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide a quality & secure test connection while quickening the test process.
-
product
64 Channel 100 KHz 16 Bit ADC Module
DP-VXI-1101
DP-VXI-1101, the 16-bit, intelligent, 100KHz A / D converter module can be widely used in data acquisition applications requiring high speed scanning with 16-bit resolution and high accuracy of 0.01% of reading.The module occupies one slot in the VXI 'C' size mainframe.DP-VXI-1101 module uses 8 channel signal conditioner plug on modules(SCP) for accommodating various input signals. Eight such SCP modules can be plugged onto the main board to accommodate a maximum of 64 channels per A / D converter module.
-
product
Metal Detector
Dor Yang precision instrument (Shanghai) Co.,Ltd
1.Fully Automatic and All Metal Detectors - Your detector detects all kinds of metal objects. Unless you have set for some objects that you don’t want to detect.2.LCD – The LCD with light, it improve to identify the metal in night or caliginous outside. 3.Target Identity - The detected objects are shown on the LCD display. You can decide immediately if the objects worth to be recovered.4.Unwanted Target Elimination - You can set the detector not to respond to some objects.5.Unique Tone for Target - You don’t have to keep watching the LCD display, when an object is being detected, an unique tone corresponding to a target will generate. You may even searching when there is little or no light.6.No Clumsy Slack Cable - hidden search coil cable (connecting between control unit and search coil) avoid entangling and for ease of stem length adjustment.7.Headphone Jack - provided for headphone connection. Both stereo or mono headphone can be used.8.Volume Control - for adjusting the output volume to the loud speaker or headphone.9.Batteries Condition Indicator - shows the conditions of the batteries in the battery compartment.10.Waterproof Search Coil - lets you use the detector in the shallow water.11.Adjustable Stem - lets you adjust the detector’s length for comfortable use. The micro-plug that connects the search coil and the controller unit is made of metal which makes the plug more reliable.
-
product
Test Leads
AL-34WB 10A
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
product
Special / Customer Spec. Crates
6U VME64x 3200
The VME 3200 crate series provides industry standard VME crates with redundant and hot-swappable front-side plugged in 500W cPCI power supplies in a compact and rugged design. The VME card sized CML shelf manager allows full remote monitoring and control of power supply, fan and chassis.
-
product
3 Digit LED Voltmeter
DPM 340
The DPM 340 is a 3 digit LED voltmeter with 8mm (0.31") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a SIL socket or can be snapped into a panel. Connection to the meter is via a single row of pins
-
product
Decoder Tester
Electronic Solutions ULM GmbH & Co. KG
Decoder tester for decoders, plug in for NEM652, NEM651, 21MTC, single wire, motor, LED monitor and 20mm speaker. It´s so easy to handle and knows all kind of interfaces.
-
product
Wrist Strap and Foot Wear Testers
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
product
DC Laboratory Power Sullies
Elektro-Automatik GmbH & Co.KG
Adjustable, programmable, 19” 3U rack-mount formatGorilla glass TFT touch display, versatile function generator, user profiles, resistance regulation, solar (PV) simulation, fuel-cell (FC) simulationAuto-ranging outputOn board 2-way interface (USB/analogue), Plug N’ Play slot for retrofitting additional interfaces such as Ethernet, CAN, CANopen, Profibus, Profinet, RS232 and moreVoltages 0-60V up to 0-1500VDCCurrents 0-20A up to 0-510A Powers 5kW up to 15kW
-
product
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36", 68-Pin Male VHDCI, 4 SMB Plugs
540103010230
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36", 68-Pin Male VHDCI and 4 SMB Plugs
-
product
Cable Assembly, Receiver, QuadraPaddle, 20", 2 RJ45 Plugs
540224010140
Cable Assembly, Receiver, QuadraPaddle, 20", 2 RJ45 Plugs
-
product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
product
Load Cell Transmitter
MODEL SST-HV
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
EMI Receiver
KH3939
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
product
50Ω uWave SMA 2.92 Cable Assembly, 40GHz, 1m
40-977-544-1m
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 1m Long.
-
product
Kill A Watt
P4400
Electricity bills are rising. Now you can cut down on costs and find out what appliances are actually worth keeping plugged in. Simply connect these appliances to the Kill A Watt®, and it will assess how efficient they really are. Large LCD display will count consumption by the Kilowatt-hour, same as your local utility. You can calculate your electrical expenses by the day, week, month, even an entire year. Also check the quality of your power by monitoring Voltage, Line Frequency, and Power Factor. Now you´ll know if it is time for a new refrigerator or if that old air conditioner is still saving you money.
-
-
product
PXI Single 4x4 1-Pole 10A Power Matrix
40-551-003
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
Compact Juno USB Interface
Juno 7Z01250
*Virtual laser power meter - From sensor to interface to PC - no power source needed*Plug and play with all standard Ophir smart sensors*Use with StarViewer free Android app to turn your smartphone / tablet into a power meter*Record every energy pulse at up to 10 KHz*Log power and energy, average, statistics, histograms and more with included StarLab application*New: Pulsed Power measurements with Thermopile sensors*New: Low Frequency Power on Photodiode sensors - power measurement based on pulse cycle (for VCSEL)*System Integrator Tools included: LabVIEW VIs, COM Object Interface*Very compact - is just an extension of the smart plug
-
product
Closed-Loop Servohydraulic Test Bench Control System
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
-
product
500 MHz RF Multiplexer Plug-In Card
1260-150
The Astronics 1260-150 is an RF multiplexer plug-in relay card for the Adapt-a-Switch™ carrier. It quickly and easily plugs into the front of the Astronics 1260-100 and 1260-101 Adapt-a-Switch™ VXIbus Carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
product
IEC60884 Fig8 Plug Strength Compression Tester
IEC60884 fig8
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig8 plug strength compression testerConforms to the standard: GB2099-1-2008 Articles 10.1 and 24.5 and Figure 8, IEC60884-1 Figure 8
-
product
54 Piece Automotive Test Connector Kit
146
This comprehensive test kit features a variety of terminal adapter sets which enable connection to most automotive vehicle connectors, both foreign and domestic. Terminal adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide wide testing coverage and quicken the test process.
-
product
PCB Adapters
Signal PCB AdaptersQuadraPaddle & TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.VTAC SIM PCB AdaptersVTAC Snap-in-Module adapters provide flexibility and modularity where custom PCBs cannot. Mix and match small modular boards to create a custom solution. Move SIM PCB adapters around to optimize space, mix protocols and match with standard patchcords. Combine protocols in a VPC SIM module and swap boards as your requirements change.
-
product
Socket Accessories (SMT Options)
The SMT adapter consists of standard high temperature FR4 with plugged via technology, eutectic SN63PB37 solder balls or SAC lead free solder balls and threaded inserts for mounting the socket. The top side of adapter has SMT pads to receive socket interconnect and the bottom side has appropriate solder balls for corresponding pitch. This FR4 adapter with balls can be soldered to the SMT pads in the target board. Then socket can be mounted to the threaded insert on the FR4 adapter.
