Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Ruggedized Laser Distance Meter with Compass
TRUPULSE 360R
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LCD Display*Range to non-reflecting targets 1.000m*Range to reflecting targets 2.000m*Accuracy in range ± 30cm (± 1m to weak targets; shown in display)*Accuracy in slope ± 0,25°*TruVector Compass Technology*Accuracy of compass ± 1° typical*RS 232/Serial interface (Model B: with Bluetooth)*IP protection IP56
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 2m HV, Exit Towards Pin 1
A050DF5-F-HA200
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.25m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Low Power SNMP AGC FTTB Optical Receiver
BGL3000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BGL3000 product series, is a low power consumption, high index, with SNMP network management, AGC, full function FTTB optical receiver. 3000 series' shells are structure compact aluminum wall hung (without rain-proof), RF interface vertical output , Nixie tube displaying parameters. BGL3000 band have RF overlay interface, is used for IP/QAM and EOC.
-
Product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Male
40-963-160-RM
-
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-03
-
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
A050DM5-F-0A050
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
PXI Ethernet Interface Module
-
The PXI Ethernet Interface Module equips PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, this module is ideal for high-performance data transfer and vision applications on the PXI platform. Additionally, the PXI Ethernet Interface Module has independent bandwidth to support up to four GigE Vision cameras without PoE.
-
Product
50Ω UWave SMA 1.0 Cable Assembly, 110GHz, 0.1m
40-977-548-0.1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Medical Needle Tubing Toughness Tester RX-01
-
The Medical Needle Tubing Toughness Tester is suitable for measuring the toughness of stainless-steel needle tubing, such as injection needles, prefilled syringe needles, and IV (infusion) needles.Product Features Supports testing of various needle wall specifications: normal wall, thin wall, and ultra-thin wall. 7-inch color touchscreen with graphical user interface (GUI) Users can freely select the bending angle and number of test cycles. This instrument features automatic data storage and retains memory even after power-off. This instrument is equipped with multiple safety features to prevent accidents caused by improper operation during testing, including an emergency stop button and overload protection. Equipped with a micro-printer and automatically prints test results upon completion Standard USB interface for convenient data transfer This instrument features multi-level user permissions, compliant with GMP standards. ISP online control and upgrade capabilities enable remote modification of test functions as needed.Test PrincipleSecure one end of the needle stainless-steel tubing and apply a force over a specified span. First, bend it in one direction, then bend it to a specified angle in the opposite direction, and repeat this bending cycle a specified number of times.Test StandardsThis test instrument conforms to many national and international standards:ISO 9626:2016 - Stainless steel needle tubing for the manufacture of medical devicesGB 15811-2025 - Sterile hypodermic needles for single useGB/T 18457-2024 - Stainless steel needle tubing for the manufacture of medical devices
-
Product
Utility Module
FTBx-9600
-
1x2 to 1x8 couplers. Various coupling ratios to fit the application. Protected component to avoid breaking or damaging. Available with EI or EA connectors, and compatible with EXFO’s Universal Interface (EUI).
-
Product
EBIRST 200-pin LFH Test Tool
93-002-001
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m HV, Exit Towards Pin 1
A050DM5-T-HA100
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
-
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
Product
Parallel NTDS Isolation Tap Box
-
IXI’S NTDS parallel isolation tap box is the ideal solution for relibility tapping NTDS parallel type A, B, C, and H interfaces. It connects easily to existing cables forming a tee connection that can be used for data monitoring and acquisition over long distances without interference with your system.
-
Product
Video Signal Generator
MSPG-5800
-
MSPG-5800 is able to support UHD (3840x2160/120Hz) resolution with Vx1 interface and also FHD (1920*1080)120Hz resolution with LVDS interface. It can be replaced with a Vx1 slot boards and LVDS Slot boards as slot type. It can also support Max 1.2GHz Dot Clock. And MSPG-5800 has Touch Screen & Graphic LCD. It can device upgrade & Option data copy easily by USB Memory Stick.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTD
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Dual Polarized Antennas
-
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
Product
Wind Measurement and Meteorological System
Moriah
-
Aeronautical & General Instruments Ltd.
MWS is a solid-state system with no moving parts, so providing a highly accurate, reliable and low cost of ownership system, which is ideal for supporting ship based aviation activities. The system comprises of 1 to 5 Solid State Wind Sensors, Dual Redundant Processor Unit, a range of Multi-Function Color Displays (8.4”, 10.4” and 15.0”) and utility Software/Graphic User Interfaces. In addition full Meteorological capability can be achieved with the inclusion of Air Temperature & Humidity, Air Pressure and Sea Temperature Sensors.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 2m, 250 Port
A500RMR-T-5C200
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6530-X4
-
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
120 GHz Frequency Extender
N5295AX01
-
The N5295AX01 modules are compact lightweight modules designed to interface to the N5292A test set controller that is driven with a PNA/PNA-X B model vector network analyzer.
-
Product
Stand Alone Low Voltage Tester
TestMate 256
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
Product
Antenna Analyzer
SARK-110
-
The SARK-110 is a completely new design concept for an Antenna Analyzer. This is a truly pocket size device, so you can take it anywhere. It offers a gorgeous 3” high-resolution, active-matrix color display that allows information-rich diagrams. The user interface has been designed to be intuitive and easy to use. On screen menus provide user guidance and the operation is mainly controlled by the two navigation keys. The graphical impedance displays provide a quick view of the antenna impedance characteristics on a user selected frequency range.
-
Product
Laboratory Air Data Test Sets
-
DMA is a leading manufacturer of Air Data Test Set models for laboratory use achieving the highest accuracy and resolution. The MPS46 is digitally controlled through a keyboard, it uses very high accuracy pressure sensors, with a special characterisation for maximum accuracy (for static channel < 2 feet at sea level). Pressure resolution of 0.2 Pa. is also achievable. The intuitive user interface with touchscreen display ensures that all the functions are controlled with a minimum of key presses . The ADTS can be used in avionics ATE systems (rack height only 2U) for automated pitot-static testing through RS232, USB, Ethernet or GPIB/IEEE488. An internal pump or external rack mounted pump unit can be supplied as an option.
-
Product
LED, Micro LED And VCSEL Measurement Systems
-
With a track record spanning decades, Gamma Scientific is a leading provider of custom, high-precision light measurement solutions for LED, micro LED, and luminaires in both the laboratory and production environment. The combination of our extensive competencies and commercial expertise has led to the development of a range of modular test solutions that can be readily integrated within the various phases of light source development and manufacturing. Each of these test modules includes measurement instrumentation, a system controller, all peripheral components, and top-level software interfaces.
-
Product
Cfast Cards
-
CFast cards (CompactFast) combine the CompactFlash form factor with a SATA interface to deliver high-speed data transfer (up to 550+ MB/s) and superior endurance for professional 4K/6K cinema cameras and industrial applications.
-
Product
13.3" FHD Industrial Display Kit
IDK-1113W
-
13.3" LCD supports 1920 x 1080 pixels, Brightness of 300 cd/m2 with LED backlight, Projected Capacitive touch solution with Anti-Finger Print surface treatment. eDP signal interface, Optical bonding, Wide view angle, Low power consumption.
-
Product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
-
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
TOV Test System
-
Shanghai Guantu Technology Co., Ltd.
1. Safety protection: traffic light indication status, emergency stop and interlocking of the test product door2. Equipped with a computer, set the TOV power supply parameters through the software interface, and automatically test3. Equipped with alarm function, equipped with emergency brake switch, equipped with safety cover and door switch4. The computer interface displays real-time voltage and current data5. Automatically draw voltage and current waveforms, and can save the waveforms as BMP format pictures, which is convenient for editing experiment reports.6. Automatically record test time, test current, test voltage, etc., and save the recorded data to files7. Installation method: cabinet installation.
