Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Digital Power Meter (AC Model)
LS2008R
-
• Measure Vrms, lrms, W, PF; • Voltage range: 10-600v, Current range: 0.005-20A ; • Accuracy: ± (0.4%reading + 0.1%range + 1digit); • Can communicate with computer through RS-232 interface.
-
Product
19’’ Rackmount 1/10 Gigabit Ethernet Switch
IC-SR-BOXa
-
The IC-SR-BOXa is based on the Interface Concept ComEth4000e Layer 2/3 1/10 Gigabit Ethernet switch into a 19’’ rack mountable box. The IC-SR-BOXa is dedicated to industrial and military networking applications.
-
Product
Interface
-
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
Product
GPIB Serial Interface Boards
-
ICS's GPIB to Serial Interface boards are designed for in-chassis applications. Select boards with transparent data transfer or boards with smart firmware that can add an IEEE-488.2 interface to any serial device
-
Product
CANbus Controller for VMEbus
VME360
-
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
Product
In Situ Diagnostics
-
For researchers working on ultra thin films and novel interfaces, Neocera offers insitu, real-time process control and diagnostic tools such as high-pressure RHEED, Low Angle X-ray Spectroscopy (LAXS) and Ion Energy Spectroscopy (IES). RHEED provides exceptional growth control via RHEED intensity oscillations and the Structural data via diffraction. LAXS is a complimentary to RHEED and provides real-time Compositional information. IES provides energetics of the laser generated plasma plume which is directly responsible for obtaining high quality films and interfaces.
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
SparkFun ESP8266 Thing
Dev Board (with Headers)
-
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
IO-Link Accessories/Connection Technology
-
- USB interface for connecting IO-Link enabled sensors to a PC- Bluetooth adapter for IO-Link sensors and masters- Repeater for increasing the range- Data splitter to integrate IO-Link sensors in old installations- Converter for converting standard signals to IO-Link and vice versa
-
Product
5 Mega Pixel Custom Lens Camera Module
e-CAM51_CU5640_MOD -
-
The e-CAM51_CU5640_MOD is a small form-factor pluggable 5 Mega pixel custom lens camera module. Moreover, a wide variety of interchangeable lenses can be used on this custom camera module. It is based on OV5640 CMOS Image sensor from Omnivision Inc. The e-CAM51_CU5640_MOD is designed to connect with any application processor that has Parallel/MIPI digital video interface.
-
Product
Navigation Aid Panel Tester
MS 1114
-
The TE-247 is 19” rack mountable test equipment used for the functional acceptance of NAP-82 and CIP-82 of Jaguar aircraft LRU’s. Microprocessor Based design and MIL1553B Bus, RS232 interface used for testing LRU’s
-
Product
Perseus SDR HF Receiver
-
PERSEUS is a VLF-LF-HF receiver made by Microtelecom is based on a outstanding direct sampling digital architecture. It features a 14 bit 80 Ms/s analog-to-digital converter with an exceptional 76 dB SNR (BW = 40 MHz), an high-performance configurable FPGA digital down-converter with an up to 1 MS/s output sampling rate and a 480 MBit/s, high-speed USB 2.0 PC interface. Unlike in lower class direct sampling receivers, the PERSEUS RF analog front-end has been carefully designed for the most demanding users and includes a 0-30 dB, 10 dB steps attenuator, a low-loss 10 bands pass-band RF preselector filters bank, and an high dynamic preamplifier with a top-class input third-order Intercept Point of more than 30 dBm. The resulting third-order dynamic range is 103 dB for SSB signals (2.4 KHz BW) and 107 dB for CW signals (500 Hz BW).
-
Product
Camera Endpoint Monitor based on Real Time Laser Interferometry
LEM Series
-
Our Real Time Interferometric Process Monitor provides high precision detection of film thickness and trench depth during the etching/deposition process.Depending on applications, LEM camera includes a 670 or 905 or 980 nm laser and when mounted on any dry etch/deposition process chamber with a direct top view of the wafer this generates a small laser spot on the sample surface.Interference occurs when monochromatic light hits the sample surface, resulting in different optical path lengths due to film thickness and height variations in the film.This allows the etch/deposition rate and thus thickness to be monitored in real time, also fringes counting or more complex analysis, providing enhanced process control Endpoint for a wide variety of processes. Additionally interfaces can be detected by their change in reflectivity.
-
Product
Negative Tester
I2C
-
telos EDV Systementwicklung GmbH
The most common use of an I2C interface is to send and receive data in compliance with the I2C specification. This implies that the device we are talking to is known to conform to the I2C standard, as well.
-
Product
3U OpenVPX Sensor Interface Unit - SIU36
SIU36
-
The SIU36 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU36 leverages NAI’s 3U boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Power Interface and Prototype PXI Card
GX7404
-
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
Pico-ITX SBC With Intel® Atom® Processor E3845/E3827, LVDS/VGA, LAN And Audio
PICO841
-
The PICO841, an extreme compact embedded pico-ITX motherboard, is designed to support the latest 22nm quad cores Intel® Atom® processor E3845 or dual cores E3827 (codename: Bay Trail) with one DDR3L system memory maximum up to 8 GB. With its compact size and ultra-low power consumption, it is perfect for space-limited and power saving environments. Otherwise, the energy-efficient embedded board is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F). Integrated with Intel® HD graphic engine, the PICO841 supporting VGA and 18/24-bit dual channel LVDS in dual-view provides faster and better graphic performance. Furthermore, to increase the connectivity and reliability, the rich feature of I/O interfaces are integrated to allow flexible cabling. Coming with two PCI Express Mini Card sockets, the pico-ITX mainboard offers excellent extensibility.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, High Voltage Outputs
M2P.6576-X4
-
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Interface
RCNIC-A2PA-TB
-
The RCNIC platform is a high performance Thunderbolt 3 device for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Field Intensity Meter
LM870-W
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Spectrum displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
Product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
-
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
ABex Terminal Module with Integrated 32x4 Matrix for NI PCIe-657x DPI Cards
ABex TM-6570 DPI
-
The ABex TM-6570 is an ABex terminal module to interface with NI PXIe 6570 / 6571 cards.In combination with the NI PXIe 6570/6571 it features a 32 channel Digital Pattern Instrument (DPI) and a 32×4 matrix, which could also be configured as a dual 16×4 matrix.As a DPI in combination with the NI PXIe 657x it offers 32 channels with up to 100Mhz, which can be individually connected and disconnected from the ABex front connector or routed to the ABex analog bus.
-
Product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
-
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
-
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-MF
-
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-FF
-
This female rear exit to female ribbon 2m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m, Exit Away From Pin 1
40-970-050-2m-MM
-
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
InfiniiMode Active Differential Probe, 3.5 GHz
N2751A
-
The N2751A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2751A probe’s InfiniiMode provides the following modes of operation.
-
Product
PXI-6541, 50 MHz, 32-Channel PXI Digital Waveform Instrument
778952-03
-
50 MHz, 32-Channel PXI Digital Waveform Instrument—The PXI‑6541 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXI‑6541 can sample digital waveforms at up to 50 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6541 also features advanced synchronization capabilities for building integrated mixed-signal test systems.
