Optical Combs
Frequency comb measuring light frequencies.
-
Product
1211a Optical Receiver/Distribution
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity.If the primary input fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
Optical OTDR
TLM-02D
-
Hangzhou Tuolima Network Technologies Co., Ltd.
OTDR-02D series Optical Time Domain Reflectometer (OTDR) is an intelligent meter of a new generation for the detection of fiber communications systems. With the popularization of optical network construction in cities and countrysides, the measurement of optical network becomes short and disperse; OTDR-02D is specially designed for that kind of application. It’s economic, having outstanding performance.
-
Product
Long Edge Wet Film Combs (Stainless Steel)
3238
-
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
-
Product
Fiber Optic Transmitter/Receiver & Repeater Board
-
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
Product
Active Optical Cable
-
Shanghai Tarluz Telecom Tech Co., LTD
Are cables with optoelectronic modules in the connector heads that convert electrical signals to light.
-
Product
Handheld Variable Optical Attenuator
VOA100
-
Shanghai Tarluz Telecom Tech Co., LTD
VOA100 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the VOA100 is used in the laser system for the on-line testing, therefore, it can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV)
-
-
Product
Multiplex Optical Maintenance Meter
LS280
-
LS280 is used to measure optical maintenance factor for high power LEDs, LED module, LED bulb or other LED luminaries. It is the important measuring equipment for performing the reliability of illuminants. • Freely set the time interval and time extent for automatic measurement • LCD Display, connect with PC via RS232 and English version software. • The test results can export Excel or PDF format and easy to compare. It can be saved by LS280 software or by USB directly. • The engineer can do LED life analysis based on the LS280 test results. • LS280 worked with High Power LED Aging Test (LS600), Multiplex LED Temperature Test (TMP-8/TMP-16) and High and Low Temperature & Humidity Chamber (GDJS-*B), it can do Flux VS Temperature VS Time, which is a perfect instrument system to meet LM-80 request.
-
Product
Hand-held Optical Time Domain Reflectometer
MT-2300 Plus
-
Guangzhou Wanglu Communications Co., Ltd.
● 3.5 inch color TFT-LCD (touch screen) ● Applicable fiber: SM ● Up to 28dB High Dynamic Range ● Flexible measurement mode switching ● Memory capacity >800 traces ● Traces fixed function mode for comparison with reference waveforms ● Provides multiple "multi-wavelength analysis" functional modes for multiple trace comparisons
-
Product
4 Way Fiber Optic Return Path Receiver (low Optical Input)
MX4RR-LI
-
The MX4RR-LI transforms return optical signals to RF signal output. The standard 1U chassis integrates 4 independent receiver modules, it can receive up to 128 return optical signals from burst mode mini-nodes or services for 128 RFoG optical network units (ONU)-Mini-Nodes.
-
Product
FIBER OPTIC MICROSCOPES
SpecVision
-
SpecVision is a video probe that engages directly with Krell polishing machines. This permits the viewing of polished optical surfaces while connectors or bare fibers are still loaded in the polisher. This in-line video inspection technique minimizes material handling and potential damage/contamination that may occur when transferring components from the polisher to a traditional microscope. SpecVision can interface with Scepter, SpecPro and Rev Polishers.
-
Product
Optical Power Meters
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifierIdeal for installers and contractors who need to certify fiber cablesIncludes the ability to measure the end-to-end length of the fiber cableUnlimited sets of job parametersMultimode and singlemode ready
-
Product
Optical Light Source
TM102N
-
TM102N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at 1625nm, 1550nm, 1490nm, 1310nm, 1300nm, 850nm、650nm, single wavelength, dual-wavelength or tri -wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.
-
Product
Optical Power Meter
PM-202B
-
The all-in-one PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-202 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
Product
Sample Pretreatment For Optical Emission Spectrometry
-
Samples are taken from molten metal, thin sheet, semi-complete or complete products. When sampling molten metal with a ladle, small quantities of molten metal are poured into a casting mold. Unnecessary parts of the sample are removed using a grinder or a cutter. As particles from a grinder may contaminate the surface of the sample, a lathe or milling machine is used (not a grinder) to cut soft samples such as white metal. If trace elements are not being investigated, a grinder or belt sander can be used. However, to minimize contamination, the grinding wheel or belt should be changed for each sample. Samples excised from semi-complete or complete products must be at least 12 mm in diameter. Small rod-shaped samples can be analyzed using special equipment.
-
Product
Optical Filters
-
Alnair Laboratories Corporation
The filter exhibits an ultra-sharp roll-off of 1500dB/nm(12dB/GHz), without compromising the flexibility ofbandwidth- and wavelength-tuning. Ideal for DWDMchannel selection and removing ASE noise.
-
Product
1310nm Direct Modulated Optical Transmitter
ONT-8600AF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Compared with ONT-8600AS, ONT-8600AF has two power supplies and fans as backup to increase its reliability. It is suitable for the areas that have instable voltage, heavy thunder and high temperature.
-
Product
Optical Power Meter & VFL
X0563
-
Optical power meter X-0563 combines the handheld optical power meter and the visual fault locator(VFL) functions in one unit. It can be used for the absolute power measurement and relative measurement of the link loss in dB. Its compact size, friendly operation interface, broad power measurement range, high precision and brand-new user automatic calibration function and high performance in application makes it an ideal tool for optical fiber network.
-
Product
Co-Packaged Optical Interleaver
-
Co-packaged interleaver consists of a pair of iterleavers in the same package. There are three input ports and three output ports. The interleaver pair may contain one interleaver (Mux) and one deinterleaver (DeMux), or a pair of (Mux) interleavers, or a pair of (DeMux) interleavers. Customers can specify configurations according to their design and applications.
-
Product
Satellite Optical Receiver
SSR-15CW
-
Hangzhou Softel Optic Co., Ltd.
*Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using high linear PD*Output connected to 5 IN series satellite multiswitch*Build-in optical AGC function*Red-LED for power indication*Smaller size and easier installation
-
Product
Mini Optical To RF Converter
MX-O2RF
-
The Maxcom MX-O2RF series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use as a tool for test and measurement
-
Product
Polymer Optical Fiber (POF) Contacts
-
VPC offers Polymer Optical Fiber (POF) contacts in the form of patchcords. POF supports low-speed, short distance applications.
-
Product
Optical Modulation Generator Software
81195A
-
The Optical Modulation Generator Software 81195A introduces a new approach to optical test. Combined with the M8195A AWG it speeds up your test by a factor of up to 100 with its unique real-time mode. This helps design engineers of long-haul and metro optical transmission applications to maximize test efficiency and thus reduce development time and cost.
-
Product
Customized Electrical Test Optical Inspection
-
Landrex Technologies Co., Ltd.
Customized Electrical Test Optical Inspection
-
Product
Optical Wavelength Meter
-
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
Product
Dispersion Compensation Optical Fiber Module
DCM-G.655-C-Fxx
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DCM-G.655-C-Fxx dispersion compensation fiber module is designed for single mode optical fiber G.655 C band, dispersion and dispersion slope compensation for wide band, the system optimized residual dispersion. The PCVD module based on optical fiber technology is mature and reliable, can improve the performance of optical transmission system.
-
Product
Optical Metrology
YieldStar
-
Our YieldStar optical metrology solutions for the semiconductor industry can quickly and accurately measure the quality of patterns on a wafer.
-
Product
Optical 12,000 Meter Connector
-
Teledyne Impulse-PDM’s 5135/5175 optical connectors utilize proven standard ferrule technology and are available for multi-mode or single-mode operation.The connectors are manufactured in Titanium Ti 6Al-4V, which is electro-polished to remove surface contamination, thus improving resistance to corrosion. The engaging nuts are also manufactured in the same grade of Titanium and the threads are coated with a Nickel/PTFE composite coating to prevent galling. The connectors have been qualifi ed to 12,000 meter operating depth.
