Optical Combs
Frequency comb measuring light frequencies.
-
Product
Short Range Straightness Optics
10774A
Optical Module
The Keysight 10774A Short Range Straighness Optics combines a straightness interferometer and reflector to make measurements over a range of travel up to 3 m (10 ft). The optics form a highly-accurate optical straightedge that can measure the straightness of travel of machine-tool and measuring-machine coordinate motions with a resolution of 0.04 micrometer (1 uin).
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
RefRad Comb Generators
-
RadRad is a battery-operated comb generator as well as a field source. It is a valuable tool for engineers ensuring the quality of radiated and conducted EMC and EMF measurements.
-
Product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
Optical Switch
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Mini Fiber Optic, Contact, ITA, Multimode
610113173
Fiber Optic Contact (ITA)
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, To SMA-plug
7-414845516-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, to SMA-plug
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
Comb Generators
-
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
Product
Comb Generator/Frequency Multiplier
TBCG2
-
The TBCG2 is a passive, step recovery diode based comb generator/frequency multiplier. It is optimized for moderate drive power and spectrum flatness in the frequency range 1 MHz to 2.5GHz.
-
Product
Erbium Fiber Frequency Comb
-
Detailed description of item: The AOSense frequency comb is a low noise, polarization maintaining (PM) device. Key features include a PM fiber architecture centered at 1550nm with turnkey modelocking; a free-running linewidth of the carrier-envelope offset frequency of <200 kHz; a temperature-insensitive all-fiber f-2f interferometer exhibiting fceo beatnotes with SNR > 45dB (300kHz RBW); and dual fast/slow cavity length actuators with a bandwidth of >300 kHz. The repetition rate of the comb is factory set and allows matching across multiple combs for dual comb applications. The optics package incorporates an optical heterodyne module designed for locking to the comb to an ITU-specified laser reference. The comb is capable of supporting an Allan deviation of < 5 x 10-18 at 1 second and ~10-20 after 105 seconds. Add-on features include all fiber extensions to visible wavelengths corresponding to several atomic transitions. An integrated comb electronics package is currently under development.
-
Product
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SC
7-413845510-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SC.
-
Product
Comb Generator
WJ10-25A
-
Comb Generator model WJ10-25A with Broadband Antenna. Frequency Range 10 MHz - 8 GHz, with two frequencies step size option; 10/25 MHz
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Plastic Wet Film Combs
154
-
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
Product
Flatness Mirror
10773A
Optical Module
The Keysight 10773A Flatness Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror, used in the 5530 Laser Calibration System, measures flatness in applications such as surface plate calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10773A.
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, to SMA-plug
7-414845510-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, to SMA-plug.
-
Product
Optics
-
Rising from our Qioptiq® heritage, Excelitas now offers precision optics in most every form and spanning the entire spectrum. You can choose from more than 4,800 off-the-shelf optical products! Our selection includes plano-convex lenses, biconvex lenses, aspheres and achromats with individual coatings, as well as plano optics, mirrors, polarization optics, electro-optics and optical design software and of course our optical assemblies and systems, such as objective lenses, optronics modules, and complex custom sub-assemblies and turn-key systems.
-
Product
PXI Dual 2 Channel Fibre Optic SC/PC
40-855-222
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Comb Generator, 10 MHz to 67 GHz
U9391G
-
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Optical Equipment
-
It is intended for the organization of multiservice, hybrid, optical-coaxial cable networks. Years of development and research in this area have allowed Planar LLC to create a product line that covers the widest range of applications. All equipment is an outstanding example of the high technology of Planar LLC, each of the models is the result of intensive research and lengthy tests. This synthesis of technical sophistication and daily labor practically means that all equipment is highly reliable and exceptionally cost effective.
-
Product
Optical Sensors
-
Analog Devices optical sensors are optical sensing front ends that include integrated ultra-low noise amplification and high performance photodiodes. These solutions are used to achieve the highest performance for instrumentation, industrial, or clinical applications; or to optimize a solution to achieve the lowest power dissipation at a given performance level for battery powered and portable applications.
-
Product
Optical Comparators
-
Starrett optical comparators provide a time tested, cost effective, solution for non-contact measurement. Optical comparators are used for an exceptionally wide range of dimensional inspection applications.
-
Product
Optic Node
OX 752
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
Optical Assemblies
-
Our team works closely with your design team to develop a custom, long-term production solution that fits your specific program. Our manufacturing niche is in low- and mid-volumes (10 to 1,000 units) for assemblies with demanding or non-standard optical performance requirements. Along with Promet’s rigorous QC protocols, our in-house testing labs and engineering support ensure a well-controlled process and predictable results.
-
Product
Mini Fiber Optic, Contact, ITA, Polymer Optic Fiber
610113171
Fiber Optic Contact (ITA)
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113170. (May mate with other Receiver contacts, as well.)
-
Product
Optical Comparator
Golden Units
-
The use of the Golden Units is the easiest way to ensure that your production devices are inspected to the accuracy you expect. The use of an optical comparator brings into play the subjectivity of the operator and errors induced by bending leads on real parts during handling by the operator.
-
Product
Optical Test
-
Optical components such as micro-lenses, diffractive optical elements (DOE), meta optical elements (MOE) and micro lens arrays (MLA) are now largely used on consumer electronics and even more optical elements need to be integrated into smaller and smaller packages. Nowadays mass-production industries key to success lies in increasing the yield by means of strongly automatized testing machines, with statistical analysis.
