Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
Product
Universal Off-Line Handler
OLS Series
-
Developed as an economical and versatile solution, it adapts to any offline test application - ICT (In Circuit Test), ISP (Flashing) or FCT (functional). The design of this solution allows the quick and ergonomic change of fixtures , with a change time of less than 3 minutes.
-
Product
Laser Diode Characterization Testing
-
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
Product
Military & Aerospace Solutions
-
Military and aerospace electronics spans a vast array of complex applications, including communications, vehicle control, radar, electronic warfare and countless others. Although the applications are widely varied, there are similarities in the requirements as well. Typically these electronic systems, whether COTS (Commercial Off- the-Shelf) or custom developed for the application, share similar requirements for ruggedness, reliability, and precision. Our customers don’t have room for error, mission critical hardware test systems must perform as designed. Circuit Check provides military and aerospace testing solutions for ITA’s, Self-Test Fixtures and Automated Test Systems that meet the stringent needs of this marketplace.
-
Product
IR LightSource
-
Universal LightSources emit Infrared (IR) radiant energy and are designed for the testing of IR(infrared) sensors used in remotely-controlled products.The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
-
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
Custom Testing
-
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
Product
Manual Fixture Kit
230351 – CMK-02
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Clamshell Type Mechanical Fixtures
-
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
Product
Architectural Preset Stations
SceneStation
-
Interactive Technologies, Inc.
SceneStation sets a new standard for full-featured, easy to use, cost-effective DMX lighting control. SceneStation is entirely self-contained in a single gang wall switch sized unit. Perfect for restaurants, high-end residential, trade show booths and more, SceneStation can control nearly any DMX device (RGB fixtures, moving lights, dimmers, effects, etc.), while also remaining very simple for the end user.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
Wireless Test Fixtures
-
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
Product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
Termination Fixture
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Main Air Data Test Fixture for ADC's
TA-245
-
This is the Main Air Data Test Fixture as shown in the AZ-241 repair manuals and will allow by the book testing of the units.
-
Product
External DC Bias Adapter
16200B
-
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
-
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
-
Product
PXI Test Instrumentation
-
The Yelo Pixi general purpose tester is a PXI based functional test system with in-circuit and continuity capability. Built into a free standing 19” rack is a PXI chassis, mass interconnect fixture interface, PC, flat screen and space for additional user selectable instrumentation.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
Product
Automotive
-
SCHILLER AUTOMATION GmbH & Co. KG
Automotive Product fixtures supports the 100/1000/MultiGBASE-T1 Compliancy standards with many different connectors such as MateNet (TE), H-MTD (Rosenberger), Mini50 (Molex). Also, we provide generic solder down board to enable engineers ability to connect their connector of choice.
-
Product
One Port Vector Network Analyser
TE3001
-
The TE3001 One Port Vector Network Analyser is built for the professional who understands the calibration process and has a network analysis task to perform. The unit features a larger output signal than the TE3000 for better noise immunity, and is supplied with a 6 piece custom calibration kit to remove the effect of test fixtures and cables. Together, these features make the TE3001 ideal for broadcast and plasma applications that require a length of cable for connection and may be high in noise or interference.
-
Product
Functional Test
UTS
Functional Test
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
6TL08 Benchtop Test Platform
H710008
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
DGN Advanced Reporting Feature, GTE 10.00p
K8223A
-
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
Product
ITA, G18, 18 Module
410120111
ITA
You can mount a VPC Enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration. This solution is perfect for any medium to high I/O PXI application. The rugged aluminum frame provides secure mounting options for custom fixtures.
