Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
Product
1.0 mm Female to Circuit Card Launch, DC to 110 GHz
11923A
-
The Keysight 11923A 1.0 mm female connector launch is designed to thread into a package or fixture housing to transition a microwave circuit from microstrip to coaxial connector. The Keysight 11923A connector launch is intended for use with 110 GHz test systems such as the Keysight 8510XF. The Keysight 11923A comes pre-assembled, but the user is responsible for machining the package and installing the connector. The procedure describing the necessary geometry for the package and installation will be provided.
-
Product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
-
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Integrating Spheres
IS-*M
-
• Diameter: IS-0.3M (φ0.3m)、IS-0.5M (φ0.5m)、IS-1.0M (φ1.0m)、IS-1.5M (φ1.5m)、IS-1.75M (φ1.75m)、IS-2.0M (φ2.0m). Other sizes can be designed according to the customer’s request. • The painting of integrating spheres is according to CIE Pub.No.84 (1989) • Material: Pure barium soleplate (BaSO4) • BaSO4 coating: ρ(λ)≥0.96 (450nm~800nm) and ρ(λ) ≥0.92 (380nm~450nm) • Fine diffuse reflection: Reflectanceρ≈0.8 and accuracy of ρ (λ) <1.5% • Build-in lighting holder position: The vertical is for E40, E27 and so on. The horizontal is for T5/T8/T12 tubes. The side assistant opening is for lighting fixtures • Auxiliary lamp position has been built-in. Auxiliary lamp and Auxiliary lamp device are optional • Power cable and socket has been build-in, it is convenient to power the testing lamp • Two photo detector ports, one optical fiber port and temperature sensor hole are built-in • The traditional integrating sphere is assembled by several pieces, Lisun Group developed A Molding Technology to produce the integrating sphere. A molding integrating sphere will be more round and the test results will be more accurate than the traditional integrating sphere
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
LCR Meter
SS10X Series
-
LCR Meters are basic passive component testing equipment, can be used in quality management department or production process for quality inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, electric valve, contactor, cable, wire, etc. This series LCR meter, offering different kind of testing fixtures, can improve testing precision and reduce the difference value of error code, being an economical and useful basic testing instrument.
-
Product
9050TR - 50 Module, 2-Tier Solution with Platform
-
The rack mountable 9050TR receiver is designed to accept 9025 and 9050 ITAs and is essential to support advanced mass interconnect requirements. This 50-module solution can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can also be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
Product
Clamshell Type Mechanical Fixtures
Series 31
-
The GR Series 31 dual well mechanical kits provide a solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility and the advantage of testing two devices on the same test fixture. These can be similar devices, or devices that are used together in a functional test.
-
Product
Electrical Tester
R580
-
Nidec-Read's R580 Electrical Tester provides an affordable test system for your bare board electrical test needs. You can easily integrate the R580 with your existing manual test fixtures or select from several fixture options from Nidec-Read. The R580 is supplied with opens/leakage test ability. In addition, you can include other advanced electrical test techniques.
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
Testing Accessories
-
Instron has used its wealth of applications and engineering experience to produce the most extensive range of accessories for materials testing instruments in the industry. Made up of hundreds of grips, fixtures, load cells, and other accessories, our vast range of general purpose and application-focused accessories are designed to help you get the most from your materials testing system.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Light source
UVM-MP
-
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
Product
Tweezers Contacts Test Fixture
16334A
-
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Functional Test Fixtures
Functional Test
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Curved Needle Test Systems
-
Instron’s Curved Needle Testing System is designed for evaluating surgical and wound closure needles through two specialized testing methods: curved needle puncture testing (per ASTM F3014) and cantilever bend testing. These fixtures assess key performance attributes such as sharpness, coating integrity, and flexural strength. Compact and efficient, the tabletop system conserves bench space while delivering robust functionality. Powered by Bluehill® Universal software, it offers comprehensive control over test execution, data collection, and reporting, along with access to a wide range of built-in calculations.
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
Product
RS232 9 Way D-Type lead
1081-001
Cable Assembly
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
Product
C68-C68-D4 Unshielded Cable, 2X68-Position VHDCI Offset, 1 m
195949-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Unshielded Digital Cable - The C68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is an unshielded, 50 Ω cable.
-
Product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
-
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
-
Product
3D Inspection Service
-
The reference data may come in the form of a table, with values at specific points or features, a cad model, or 3d scan. 3D inspection services may require datum measurements, where the part to be inspected is located in a fixture that is specifically designed to orient the part by an ordered method. In some cases, the part may have features that are designed specifically to be referenced by datums, if no functional feature of the part provides a clear reference.
-
Product
Non-Linear Junction Detector
ORION® 2.4 HX
-
The ORION 2.4 HX Non-Linear Junction Detector (NLJD) detects electronic semi-conductor components in walls, floors, ceilings, fixtures, furniture, containers, or other surfaces. The ORION 2.4 HX NLJD is made to detect and locate hidden cameras, microphones, and other electronic devices regardless of whether the surveillance device is radiating, hard wired, or turned off.
-
Product
Utility Card: Flash Programming Applications
-
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
