Link
See Also: Camera Link
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Singlemode Power Meters and Laser Sources
-
The KD Optics range of Singlemode power meters and Laser sources are designed for the testing of SDH, CATV, Telecom and other singlemode links. The power meters are highly accurate with a wide dynamic range, while the laser sources feature a very quick stabilisation time, promoting accurate readings.
-
Product
With SAT-IF input EDFA
HA4600/IF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
Product
Active Optics
-
Radiall designs and manufactures end-to-end optical links for massive data transfers in harsh environments.
-
Product
PXIe-8398, Gen 3, x16 PXI Remote Control Module
784178-01
MXI Express
PXIe, Gen 3, x16 PXI Remote Control Module—The PXIe-8398 enables control of a PXI Express chassis from an external host, such as a desktop PC, rackmount controller, or a separate master chassis. Using a Gen 3 x16 PCI Express link, the PXIe-8398 provides up to 16 GB/s of data transfer between the chassis and host over a copper cable connection.
-
Product
LXI High Density 32x64 2A Matrix with BIRST
60-552-023
Matrix Switch Module
It is constructed from 8x64 sub-assemblies, permitting the matrix to be supplied in a variety of sizes from a single 16 x 64 to 64 X 64 and dual 8x64 to 32x64. Larger configurations can be easily achieved by utilizing the Loop thru connections on either the X or Y bus, for instance, four 64x64 units can be linked to create a 128x128 matrix.
-
Product
End Point IP Core
PCIe
-
The highly configurable PCIe End point IP core supports x1, x2, and x4 lane with a selection of 32/64-bit data path. Depending on design requirements, a maximum of 8 VCs and 8 TCs are supported. The IP core consists of many useful features that can be included to enhance system performance and to address special design needs in different applications. The data link layer allows the configuration of infinite credits to boost the flow control efficiency. By-pass mode, cut-through mode, and store-and-forward mode are other optional items. The transport layer features include configurable ECRC generation and checking, support for up to 64 configurable outstanding non-posted requests, and configurable payload size from 128 to 4 Kbytes
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 4-Channel, 16-Pole
42-614D-014
Multiplexer Module
The 40-614D-014 (PXI) and 42-614D-014 (PXIe) 2-bank, 4-channel, 16-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Non-contact Ultra-High Range Sheet Resistance Measurement System
CRN-100
-
*Ultra-High range sheet resistance measurement for 10E+9 ~ 10E+15 ohm/sq without contacting*Mapping program software;*1. Arranged in a multipoint pattern measurement is programmed*2. 2-D & 3-D mapping software*Easy operation by Windows 7 system software*Measurement data base link with Excel via CSV format file*Unaffected by contact resistance
-
Product
TRansceiver Module
CFP2
-
Eoptolink Technology Inc., Ltd.
Eoptolink CFP2-100GBASE-LR4 / CFP2-100GBASE-ER4 module supports a link length of 10, 20, 25 and 40km kilometers on standard single-mode fiber (SMF, G.652). 100 Gigabit Ethernet signal is carried over four wavelengths. Multiplexing and demultiplexing of the four wavelengths are managed within the device.
-
Product
Xtium2 Frame Grabber Family
-
The Xtium2 series leverages the PCIe Gen3 x8 platform to deliver high- speed image transfers to host memory without CPU overhead. Featuring Camera Link HS® interface standards, supports Active Optic Cable and SFP+ modules, CoaXpress® 12, and Camera Link®.
-
Product
VME to USB 2.0/Optical Link Bridge
V3718
-
The V3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the V1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device. The mechanics is 1-unit wide VME 6U.
-
Product
Fibre Channel Simulator & Analyzer Applications Software
fcXplorer Simulyzer
-
Avionics Interface Technologies
FC-1, FC-2, and FC4 Analyzer modes and displays - Frame parser for custom display of FC frames and payload data - Captured data can be saved as binary or “csv” files - User-defined trigger and filter features - “Live Capture” real-time display - Error detection and reproduction - Complete control of the transmit link - Replay of recorded data with precision timing or corrected protocol timing - Special testing functions such as defining command/response for exchange management
-
Product
IO-Link
-
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
Product
Pluggable Optical Line System
POLS
-
Use our compact pluggable modules to provide up to 8 DWDM channels to enable high-capacity optical inter-datacenter links for internet service and cloud hosting providers.
-
Product
Media Converter, 100Mbps, Single Mode 1310nm, 30km, SC
EKI-2541S
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Single-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mount
-
Product
Operating System Support Software
-
Diamond Systems offers software support for our embedded computer boards, ranging from drivers to complete OS board support packages. The currently available driver and BSP support can be found by clicking on the links below. If what you need is not listed, please contact us to discuss custom software support options.
-
Product
LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ ATX Server Board with 4 DDR4, 7 PCIe, 6 USB 3.1, 8 SATA3, Quad/Dual LANs, IPMI
ASMB-786
-
- LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ i7/i5/i3 processors with C246 chipset- DDR4 2666/2400/2133 MHz ECC/Non-ECC UDIMM up to 128 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCIe x1 slots- Triple displays - DVI-D, VGA and HDMI 2.0 ports- Eight SATA3 ports and six USB 3.1 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60° C ambient operating temperature range
-
Product
Link simulation to ATE conversion
VCD2ATE
-
VCD2ATECost effective link simulation to ATE conversionDirect conversion from event driven design simulation dump (VCD/EVCD) to specific tester program files. VCD/eVCD to tester conversion Simple and cost effective conversion solution Simple cycle definition in excel High Performance Fast run time Handles very large files >6Gb
-
Product
IO-Link Master
-
- For connection of up to eight IO-Link devices- Reliable transmission of machine data, process parameters and diagnostic data to the controller- Simultaneous data exchange with the controller and the IT world- Mounting flexibility for field mount or control cabinets- With integrated fieldbus interface
-
Product
PXI MUX 4 Banks of 32 Channel 1 Pole
40-610-022-4/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Optomechanics
-
Welcome to Thorlabs; below you will find links to our extensive Optomechanical product line, a subset of our entire line of photonics products. Optomechanics is a broad category that includes optical tables and breadboards, optical mounts and construction components, mechanical devices with integrated electronics, kits that make it easy to buy a popular set of components or a set of components that can be assembled to perform a specific function, and general laboratory supplies and tools. Because of the large selection, Optomechanics does not include translation and rotation stages and their controllers; instead those products have their own category.
-
Product
Multi Monitor
LV 5770A
-
The LV 5770A is a multi monitor that can be customized with a variety of units to meet your needs.The LV 5770A is highly cost effective because it supports full-format 3G-SDI, HD dual link, HD-SDI, and SD-SDI signals. The LV 5770A has a variety of features including simultaneous monitoring of two SDI signals, SDI signal frame capture, lipsync measurement, Pic Moni Output, and improved flexibility in laying out the display, all of which provide you with leading-edge technology.
-
Product
FireBird Camera Link Frame Grabber (1xCLD-2PE8)
AS-FBD-1XCLD-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
TDL Training Tools and Services
-
Curtiss-Wright Defense Solutions
To prepare for the threats of the battlefield, warfighters must be familiar with what they will encounter. With extensive experience in tactical data link training and technology, Curtiss-Wright has the tools and expertise to provide your organization with solutions that facilitate tactical data link communication on the battlefield.
-
Product
- Optically Isolated Line Driver
Model 72A
-
FEATURES: DC TO 19.2 KBPS; Optically Isolated; TD & RD LED's; Loopback Switch; Built-In Surge Protection; Male or Female Connectors; Screw Terminals and RJ-11. The Model 72A Optically Isolated Line Driver links RS-232 based devices over extended distances. It provides optical isolation and has built-in verification of operation using a loopback switch.
-
Product
Fiber Optic Talk Set
-
Fiber optic talk set consists of both the fiber optic light source and transceivers, which carry voice over the spare fiber in both directions. When doing the test work, technicians may need remote location communication during the measurement or splicing work, and sometimes radio-based communications may not be suitable because of environmental conditions such as FCC restrictions, etc. fiber optic talk set will function well in such cases, they could utilize the already installed fiber optic link to carry voice communications.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 32-Channel, 4-Pole
42-614D-017
Multiplexer Module
The 40-614D-017 (PXI) and 42-614D-017 (PXIe) 1-bank, 32-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
