Force Transducers
-
Product
Force Distance Tester
925
-
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
Product
Linear Motion Tandem Transducer
-
Columbia Research Laboratories
The Columbia Model LMT-50 is a unitized rugged package consisting of tandem linear variable differential transformers (LVDT's) with probe assembly. The LMT-50 is designed so that the likelihood of a single failure affecting both output signals is extremely improbable. The model LMT-50 offers flight proven performance, even in the most severe environments.
-
Product
Motorized Force & Torque Measurement Test Stands
-
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
The force sensors can be integrated easily and uncomplicatedly by the regular standard thread.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Signal Conditioners & Measuring Transducers
-
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
Product
Combined Pressure and Temperature Transducers
-
We offer some different styles of combined pressure and temperature transducers which are well suited to Motorsport applications. These include the EPTT5100 combined pressure and temperature transducer, which, has an internal temperature sensor, and the miniature EPTTE1400 combined pressure and temperature transducer which has an external temperature probe.
-
Product
Mechanical Force Gauges
-
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
Product
Coercive Force Meter
-
The meter is mainly used in measuring the coercive force of magnetic components of relays and the mechanical energy meter compensation films, which is the essential instrument of manufacturers who are producing the relays and the energy meters, etc.
-
Product
Displacement Transducers
-
Displacement transducers are suitable for direct, accurate measurement of displacements in automatic control and metrology.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 155gf
K100-L150155-SKAU
-
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Transducers with 4-20 mA Output
-
Transducers / transmitters for temperature, humidity, atmospheric pressure and CO2 with 4-20mA interface.
-
Product
Electrical Power Transducers
-
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
Product
Power Transducers and Load Loggers
-
Power Transducers and Load Loggers by Ametek Power Instruments
-
Product
Acoustic Emission Transducer
ZET 601
-
The acoustic emission sensor is the most important element of any acoustic emission NDC system. The ZET 601 acoustic emission transducer converts AE-process acoustic signal to an electric signal parameters of which are used for the assessment of acoustic emission sources.They are used for technical diagnostics using passive ultrasound.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
Scanning Probe Microscopy/Atomic Force Microscopy (SPM/AFM Analysis)
-
Rocky Mountain Laboratories, Inc.
Scanning probe microscopy (SPM) refers to a family of measurement techniques that utilize a scanning probe. The most common measurement is Atomic Force Microscopy (AFM Analysis), which measures surface topography. Imaged areas can be from the nm scale to as large as 100 µm X 100 µm. Heights and depths of features can be measuredand many surface roughness parameters, e.g Ra, can be calculated. 3-D images can also be produced for dramatic data presentation. Magnetic and electrical response can also be measured with SPM.
-
Product
Atomic Force Microscope
NaioAFM
-
The NaioAFM is the ideal atomic force microscope for nanoeducation and basic research on small samples. This all-in-one AFM system provides solid performance and easy handling, with a price tag and footprint that fit anyone and any place.
-
Product
Combined Pressure and Temperature Transducers
-
We can offer some different styles of Combined Pressure and Temperature Transducers. The EPTT5100 combined pressure and temperature transducer has an internal temperature sensor. The miniature EPTTE1400 combined pressure and temperature transducer has an external temperature probe.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 230gf
K100-G150230-SKAU
-
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Linear Position Sensors and Transducers
-
Linear Position Sensors and Transducers are used throughout many industries including; test/lab applications, medical applications, Motorsport, industrial processing, industrial machinery and mobile vehicleapplications. You may have come into contact with these types of sensors in everyday life. Some of the applications that they are used for include:
-
Product
Atomic Force Microscope
NX10
-
Park NX10 produces data you can trust, replicate, and publish at the highest nano resolution. From sample setting to full scan imaging, measurement, and analysis, Park NX10 saves you time every step of the way. With more time and better data, you can focus on doing more innovative research.
-
Product
Force Transmitter
LKVE/i
-
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 230gf
K100-Q080230-SKAU
-
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
