I²C
A slow Inter-Integrated Circuit bus protocol.
-
product
Gauge Type T Thermocouple Wire
W-TW-36
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Isoperibol Calorimeter
AC500
The AC500 determines calorific value, a key indicator of quality and value in solid and liquid fuels, through measurement of the heat released after combustion of a sample. This stand-alone benchtop unit uses a fully-integrated circulation system for a compact footprint—no additional heaters or coolers required. An integral water-measuring station simplifies sample preparation, and a Windows®-based operating system uses an electronic thermometer accurate to 0.0001°C to measure temperature every six seconds. Two-channel correction is possible through constant temperature monitoring in both the outer jacket and the calorimeter proper.
-
product
Fully-Automatic Kjeldahl Analyzer
LD-LKA-C10
Fully-automatic Kjeldahl AnalyzerLD-LKA-C10conducts titration and distillation simultaneously so as to neutralize the ammonia gas released which enhance the test efficiency and avoid the overflow of ammonia. It stand with a measuring range from 0.1 to 200 mgN which gives a maximum recovery of ≥ 99.5 %. The operating ambient temperature of the device starts from 10 °C to 35 °C. 8.0-inch LCD touch screen is used to set the distillation time, the amount of diluent, acid liquor and alkali. Diaphragm pump is used to add reagent so that the injure caused by high pressure pump can be neglected. Wireless network modules is installed for realizing remote data transmission to test data processing and report printing.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
Satellite Interception system
Shoghi has designed and developed various solutions to passively intercept traffic (Voice, Fax and Data) from Global Mobile Personal Communications by Satellite (GMPCS) and point to point satellite communication networks.All solutions are fully integrated monitoring and analysis platform which enables acquisition, processing, storing and analysis of Voice, Fax, Data and High speed IP traffic.To challenge the various monitoring scenarios Shoghi has designed both tactical and strategic solutions equipped with automatic post processing, decoding demodulation and decryption of intercepted Voice, Fax, Data and High speed IP traffic.Our GMPCS Satellite monitoring solutions are capable of intercepting Voice, SMS, Fax and Data traffic along with Call Related Information and Geo-location from Thuraya-2, Thuraya-3, ISAT Phone Pro, Iridium satellite networks.The point to point satellite communication monitoring systems are capable of intercepting traffic including Voice, Fax and Data from C and Ku-band satellite carriers from Intelsat, Eutelsat, Arabsat, Turksat etc. The Satellite Monitoring system can also process and decode GSM traffic on satellite and decode high speed IP traffic online.1.Satellite Monitoring Solutions:2.Satellite Carrier Analysis System3.C/Ku Band Satellite Monitoring4.DCME Analysis System5.GSM Abis Link Monitoring Module6.IP Link over Satellite Monitoring7.Satellite Carrier Reconnaissance and Analysis System8.VSAT Monitoring System9.Satellite Terminal Geolocation System
-
product
Ultrasonic Thickness Gauge
QTG Series
Ultrasonic Thickness Gauge - QTG Series are economical, user-friendly, menu driven, and multi-functional units offering extensive features from basic measurements (model: QTG I) to extended memory (5000 reading storage) and USB output capabilities (model QTG II). The instrument can measure with very high resolution (0.01 mm or 0.001 inches) the thickness of metallic and non-metallic materials such as steel, aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave conductor. The Ultrasonic Thickness Gauge - QTG Series accurately displays readings in either inches or millimeters and is equipped with special features like Automatic recognition of probes with different frequencies and Automatic zeroing of the unit.
-
product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Run-Time Error Analyzer
Astrée
AbsInt Angewandte Informatik GmbH
Astre analyzes structured C programs with complex memory usages, but without recursion or dynamic memory allocation. This targets embedded applications as found in earth transportation, nuclear energy, medical instrumentation, aeronautics and space flight, in particular synchronous control/command such as electric flight control.
-
product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
783730-01
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
product
Medical Panel PC
ADLINK offer two series of medically certified, hygienic, all-in-one (AIO) computers designed to streamline patient care by supporting PDMS, HIS, vital sign monitoring, nursing care, clinical diagnosis, PACS, anesthesia monitoring, and operating room documentation. The MLC 8 series is MDR Class I certified and delivers superb performance and configuration versatility to meet unique application requirements. The MLC-AL/MLC-KL series is specially designed for integrated system control and management of complex medical data and imagery in space-constrained healthcare environments.
-
product
Digital AC/DC Auto-Ranging Clamp Meter
PCMT20
Measures AC and DCMax. Resolution to Current Measurement: 0.1uALCD Display with BacklightData Hold, Zero Function, Auto Power OffLower Battery Indiactor0.9' (23mm) Jaw SizeDC Voltage: Range: 0-600 V; Accuracy: +/- 0.5%AC Voltage: Range: 0-600 V; Accuracy: +/- 1.5%AC Current: Range: 0-400 A; Accuracy: +/- 3.0%Resistance: Range: 0-40 M; Accuracy: +/- 3.0%Temperature: Range: 1000 C / 1832 F; Accuracy: +/- 3.0%Capacitance: Range: 100 uF; Accuracy: +/- 2.5%Frequency: Range: 150 kHz; Accuracy: +/- 1.2%Continuity: Buzzer Sounds at 100Diode: Test Current 0.3mA; Open Circuit Voltage 1.5VBatteries: 2 x AAA IncludedAccessories Included: Black Bag, Test Leads, Type K Temperature ProbeDimensions: 8.07' H x 2.36' W x 1.18' DWeight: 7.94 ozSold as : Unit
-
product
Endevco Cryogenic Charge Output Accelerometers
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
product
FD-11613, 8-Channel Temperature Input Device for FieldDAQ
785640-01
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
product
Multiloggers
Save data: 128 samples with real-time data.Data logger: 16 sets, Maximum 1024 data capacity.Easy Reads Data with down and up key on meter.T/C Offset Adjust.REC, MAX, MIN, MAX-MIN, AVG, REL, HOLD functions.T1, T2, T1-T2, Time and Memory No.Resolution 0.1°C/1°C, 0.1°F/1°F.Warning beeper with Hi/Lo setting.Real time clock with calendar.Selectable Auto Power Off function.
-
product
Infrared Thermometers
Easily measure surface temperatures with ThermoWorks non-contact IR guns, ideal for produce and agriculture inspectors, HVAC, construction, warehouse, quality assurance, HACCP and cold chain management, both shipping and receiving. Choose from fixed or adjustable emissivity; single, dual or circle laser types; and lens optics from close focus—for electronic components and laboratory measurements—to 100:1—for long distance measurements. High temperature ranges up to 3272°F (1800°C) are perfect for metallurgy and metal work foundries.
-
product
Code Complexity Measurement Tool
CMT Java
The Code complexity measurement tool Testwell CMT++ (for C, C++ and C#) and Testwell CMTJava (for Java) saves costs and avoids software erosion. For this reasons several standards (like ISO 26262) require the enforcement of low code complexity.
-
product
Micro SIL Reed Relays
Series 108
SIL relays - 0.15 inch wide packages. Requires a board area of 0.15 x 0.8 inches (3.8mm x 20.3mm). 10 Watts Form A or 3 Watts Form C switches in Mu-metal package
-
product
Precision Programmable Attenuator
RCDAT-30G-30
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
product
Managed Ethernet Switches
CommFront offers a range of rugged, industrial-grade, managed and unmanaged Ethernet Switches. These Industrial Ethernet Switches have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of 10/100/1000M for both Fast and Gigabit Ethernet networks. In addition, our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet Switches support both point-to-point and multi-drop (daisy-chain or self-healing redundant ring) fiber optic networks, which are designed to cover large areas. These industrial Ethernet Switches support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. When configured as a ring network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same ring, making the entire Ethernet network more robust and reliable.
-
product
Precision Temperature Bridges - AccuBridge® Line
Measurements International Ltd.
Multiple Display Modes Including: Temperature (°C, K, °F), Resistance, Ω, Ratio, ADCC Technology, Accu-T-Cal™ Software (NMI Designed).
-
product
PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor
784176-01
The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound
-
product
NI-9251, 3 Vrms, 102.4 kS/s/ch Simultaneous, 2-Channel C Series Voltage Input Module
783814-01
3 Vrms, 102.4 kS/s/ch Simultaneous, 2-Channel C Series Voltage Input Module - The NI‑9251 with mini XLR is a low-distortion input channel that allows for the high dynamic range measurements necessary to fully test and evaluate modern audio outputs used in most consumer electronic devices. Unlike sound card-based solutions, you can quickly deploy the NI‑9251 to guarantee long-term measurement repeatability and increased test system uptime. To maximize low-noise benefits, the NI‑9251 differential input is provided through a mini‑XLR connector, which delivers a truly balanced input.
-
product
DC/DC Converter 3.5 W
REM3.5E-2424S/R6/A/SMD
DC/DC converter with 3.5 W from Recom | input ranges 18 - 36 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 1m, HV
40-972-037-1m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Digital Temperature Sensor
STS35
Sensirion, a leading provider of environmental and flow sensor solutions, presents the STS35 temperature sensor – the most accurate sensor of the versatile STS3x series. The high-accuracy temperature sensor has been designed to fulfill the needs of demanding markets such as the medical and automotive sectors. Typical applications include body temperature measurement and temperature control. Typical accuracy of up to 0.1°C.
-
product
Temperature Measurement IR Sensors & Detectors
S25 TO-5
A single-channel silicon-based thermopile that offers the smallest single element active area size at 0.25mm x 0.25mm in a TO-5 package. Delivers a fast 18ms time constant in Argon encapsulation gas and even faster with Neon gas at 9ms. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C.
-
product
Medium-Temperature
Medium-temperature processing systems deliver more thermal energy than low-temp tools can provide, without crossing into the stress-inducing range of high-temp processes. Operating between 200–600°C, they create the perfect balance for enabling critical film transformations, crystallization and adhesion. Medium-temperature MBE sources can be used for virtually any application—from hot-lip SUMO sources to standard filament for thermal effusion.
-
product
Fanless Edge AI System With NVIDIA® JETSON™ TX2 Series SoM, 1 HDMI, 2 GbE LAN, 2 USB, 2 COM Or 2 CAN And 12 Or 24 VDC
AIE500-901-FL
The AIE500-901-FL is an advanced Artificial Intelligence embedded system for edge AI computing and deep learning applications. The high-performance embedded system employs an NVIDIA Jetson™ TX2 module which has a powerful 64-bit ARM® A57 processor; NVIDIA® Pascal™ GPU with 256 CUDA cores; and 8GB of 128-bit LPDDR4 memory. To withstand the rigors of day-to-day operation, the AIE500-901-FL has an extended operating temperature range of -30°C to +60°C and vibration of up to 3 Grms with its strong construction. This fanless Artificial Intelligence edge system is dedicated to achieving operational excellence, efficiency, reliability in smart manufacturing and intelligent edge applications. The edge computing device provides solutions as Edge AI embedded system, specifically designed for video analysis, object classification, computer vision, quality control and more. Under the ultra-compact enclosure design, the AIE500-901-FL comes with 32GB eMMC onboard and is equipped with one M.2 Key M 2280 SSD slot with PCIe and SATA signal and one Micro SD slot for massive data processing and AI applications. Besides, this reliable embedded system has one full-size PCI Express Mini Card slot and one SIM slot for 3G/4G, GPS, Wi-Fi and Bluetooth connections.
