Bus
One or more conductors or optical fibers that serve as a common connection for a group of related devices
See Also: Serial, Parallel, Bus Analyzers, Bus Adapters, Bus Converters, Bus Interfaces, Bus Translator, Extender Boards, Extender Cards, Cable Bus
-
product
PXI 4 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-021-230X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
13-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/13L
*1 PICMG, 4 PCI and 8 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Bus Differential System
B90
The B90 Bus Differential System provides fast and secure low impedance bus protection for reconfigurable LV, HV, and EHV busbars. Use one B90 to protect up to 8 feeders and use three or more B90s together in a centralized phase segregated architecture to protect up to 24 feeders.
-
product
LXI Wired Trigger Bus Adaptors And Accessories
We manufacture LXI Wired Trigger Bus adaptors and accessories. These adaptors and accessories are designed to help debug a WTB system or provide conversion of signals to or from the WTB to products that do not support the WTB. LXI approved WTB cable assemblies and terminators are available to interconnect LXI devices that support the LXI Wired Trigger Bus extended function.
-
product
6-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/6VP4
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX61222TP/AX61220TP*Supports ATX power supply*For 2U chassis
-
product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 3 Bus Matrix Inputs
40-569B-113
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-113 is a 8 slot module fitted with 3 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
product
PXI 4-Slot BRIC Matrix, 184x8, 1-Pole (4 sub-cards) Dual Bus
40-560B-021-184X8-M
The 40-560B-021-184x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8 Slot BRIC 322x8 1-Pole Dual Analog Bus (7 sub-cards)
40-560A-121-322X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
LXI Reed Relay Matrix - Single 32x32 Plugin, No Direct Y Access, 1 Analog Bus
65-227-101
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
PXI 4 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-021-184X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 6 Bus Matrix Inputs
40-569B-126
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-126 is a 8 slot module fitted with 6 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
product
40U (70") Insulated Bus Bar
BB-70-I
40U (70") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
A²B® Automotive Audio Bus Solution
ITD 1024
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
product
PCI BUS Interface Card
PCI301
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
Bus Analyzer
FireSpy430b(T)/830b(T)
The FireSpy430b(T) and FireSpy830(bT) bus analyzers are the single bus models in the 4th generation of IEEE-1394 analyzers from DapTechnology. Based on the industry leading FireSpy810 the all new and enhanced architecture of the FireSpy430b(T)/830b(T) have again defined a new reference in IEEE-1394 test equipment! They comprise a significantly more powerful on-board processor, more memory and improved connectivity to the host.
-
product
20U (35") Insulated Bus Bar
BB-35-I
20U (35") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
product
1-port CAN Bus Data Logger
CAN-Logger100
The CAN-Logger100 is a high-performance smart CAN bus data logger with one CAN port that can help collect data and process on a CAN bus network easier and quicker. The powerful CPU of the CAN-Logger devices provide the accurately time-stamp for each CAN message and support storage media like SD card or SDHC type flash to save CAN messages, which helps users easily analyze and diagnose the CAN Bus network. Providing great portability, the CAN-Logger100 is powered by USB interface or M12 connectors of CAN bus interface. The CAN-Logger100 device uses the standard USB HID driver of the Windows system.
-
product
STD Bus, Vectorbord Plugbord
4610-3
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers.Pad per hole and peripheral buses both sides.Row and column legends provided.
-
product
Enterprise Service Bus
Kovair Omnibus
Software teams are using multiple best of the breed tools but mostly they work in silos without real-time sharing of data.Now integrate those tools through Kovair Omnibus to achieve cross-team and cross-tool collaboration across disparate systems.Choose from the list of 70+ integration adapters or connectors developed by Kovair.
-
product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB100
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
product
STD Bus Backplane
VECTOR Electronics and Technology, Inc.
Vectorbord® STD Bus industrial backplanes per IEEE 961 microcomputer bus, compact and rugged are fully assembled and tested. Designed for 4.5” X 6.5” plug-in boards, Vector STD Bus backplanes are available in 8 or 16-slots. Speed capability up to 10MHz; 2-layer design. Ample positions for decoupling capacitors; interrupt priority lines.
-
product
PXI 8 Slot BRIC 368x8 1-Pole Dual Analog Bus (8 sub-cards)
40-560A-121-368X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
LXI Trigger Bus Cable
ProDAQ 8036
The ProDAQ 8036 LXI trigger bus cable connects the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface to any device equipped with LXI triggers. The robust, shielded cable and the die-cast connectors ensure a stable connection and prevent accidental disconnects.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
CompactPCI CTEL 6U 8 slot with H110 bus, P1-2s
105CTEL608-0136
CompactPCI CTEL 6U 8 slot with system slot left, H110 bus, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
