-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-125
Programmable Resistor Modules
The 40-297A-125 (PXI) and the 42-297A-125 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Programmable Limit Switch-Internet Communications
PLS1000i
-
Computer Conversions Corporation
The PLS1000 is a programmable limit switch designed to allow convenient programming of 16 circuits.The PLS1000 is designed to be panel mounted.
-
Product
Dual-Channel Power Supply
DPS16
-
The DPS16 is a dual-channel power supply with very low output noise and no ripple. The output current can be up to 200 mA and has a programmable current limit. The 4 wire capability provides an excellent load regulation. Because the DPS16 is a fully linear design the output noise is exceptionally low while there are no ripple components as usually seen with switched mode designs. The unit has voltage and current read back on both channels with 16-bit resolution.
-
Product
Universal Transmitter
Ut4623
-
Programmable via detachable Programming Unit (UT4624), process calibration, signal and relay simulation, password protection, errordiagnostics and selection of help text
-
Product
PXIe-4113, 2-Channel, 10 V, 6 A PXI Programmable Power Supply
782857-02
Programmable Power Supply
The PXIe‑4113 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm
50-294-024
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Avionics ATE Power Subsystem
-
AMETEK Programmable Power, Inc.
*Provides eight channels of programmable DC power with output isolation function*Output disconnect function*Total control via Ethernet within power supply.*Mounted in custom in transportable shock-mount case.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
Digital I/O Module
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 6U VPX
Model 57841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with one 3.6 GHz, 12-bit A/D- Two-channel mode with two 1.8 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
DC Power Supplies
XG 1700
-
AMETEK Programmable Power, Inc.
The XG 1700 is an industry leading programmable DC power supply designed for test, production, laboratory, OEM and quality assurance applications. The XG 1700 is a 1700 Watt, 1U programmable power supply with constant voltage and constant current modes, automatic cross-over and numerous features enabling cost effective, easy integration.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
Programmable Resistor Modules
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Power Supplies
T3PS Series
-
The Teledyne Test Tools range of DC Bench Power Supplies comes in non-programmable and programmable versions with one, two, three and four output configurations. Key features within the Teledyne Test Tool Power Supply range include programmability via USB or LAN, a graphical display of power waveforms, as well as high resolution numeric display of voltage and current. Typical customer applications for DC Bench Power Supplies include those in industries such as mobile, automotive, communications, defense, and manufacturing as well as those within teaching, education and research institutions.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-352-HI
-
The 40-230-352-HI (PXI) and 42-230-352-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Function Modules
-
NAI offers over 70 smart, field-proven function modules covering a wide variety of I/O, Measurement and Simulation, Communications, Ethernet switch and SBC functions. With Off-the-shelf development and quick integration speed, NAI's function modules provide the ability to reconfigure and respond to changing design specifications reducing NRE charges and offering obsolescence protection all with unmatched flexibility with countless hardware & software combinations. Each smart function module has dedicated FPGAs on-board with memory map-based configurability, programmable PID loop support and health monitoring via Built-In-Test. A single API provides programmability across all leading to a more I/O-intensive, distributed, smart and total cost-effective mission system.
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-111-HI
-
The 40-230-111-HI (PXI) and 42-230-111-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 62.1Ω with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Benchtop LCR Meter
1692
-
The GenRad 1692 LCR Meter is a sophisticated, microprocessor-controlled tester that brings new levels of flexibility, simplicity and accuracy to RLC measurement. It's testing automation at its best with a range of programmable test frequencies and test voltages, as well as automatic limit comparison, automatic parameter selection, remote programmability, automatic binning and automatic zeroing. The display facilitates visual acquisition of test data and eliminates costly guesswork and errors. The 1692 LCR Meter provides a powerful combination of features designed to maximize productivity in production testing applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-133
Programmable Resistor Modules
The 40-297A-133 (PXI) and the 42-297A-133 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Universal Programmer
SUPERPRO/7500
-
eMMC programming speed 10 times higher than SuperPro/5000;Universal package adaptors thanks for 144pin universal Pin-drivers;Engineering and production programmer in one unit.
-
Product
LVDT I/O Cards
CP3000
-
Computer Conversions Corporation
Universal AC Sensor interface digitizes up to 8 channels of individually Programmable Synchro, Resolver and LVDT/RVDT sensor inputs on a 3U cPCI (Compact PCI) and PXI Compatible plug-in circuit cardProduct allows users to interface into the widest variety of AC Position sensors all programmable within a single cardA must have for anyone using LVDT-RVDT's, Synchros and Resolver sensors or signals, electronic gauging, motion control, and instrumentation.
-
Product
Measuring Light Curtains
-
Leuze electronic GmbH + Co. KG
These devices are perfect for measuring moving objects as they pass by. The measurement results can be output via the fully integrated interface. At the same time, the programmable switching outputs allow downstream elements to be manipulated. Likewise, multiple light curtains can be cascaded. The nearly unlimited possibilities for configuring multiple measurement areas and evaluation functions make the devices problem solvers for a variety of measurement tasks. The range of available resolutions and measurement field lengths ensures optimum adaptation to your application.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-356-HI
-
The 40-230-356-HI (PXI) and 42-230-356-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Universal Programmable Transmitters
-
Omega offers a large selection of programmable universal transmitters that accept universal inputs including mA and Vdc process signals and all commonly used temperature signal types.
-
Product
PCIe 16 Bit Multipurpose Digitizer - up to 40 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5932-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
Programmable Delay Line Instrument
XS-100
-
The XS-100 is designed for those who need faster switching speeds and measurements without interruptions
