Thermal
The radiation of heat.
See Also: Energy, Chemical, Electrical, Nuclear, Electromagnetic, Thermal Shock, Thermal Test, Infrared
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
Digital I/O Module with 32 24V/0.5A outputs
IO205
-
This I/O module is a dedicated digital I/O module providing 32 channels of 24V/0.5A outputs. The digital outputs are also galvanically isolated by opto-couplers. All outputs are protected against short-circuit and thermal overload and can output up to 0.5A per channel.
-
Product
Discrete Detectors
-
TRAL test station is a quasi-universal test station designed to measure parameters of discrete (or small linear array) infrared detectors sensitive in a wide spectral range from about 700nm to about 16 000 nm (NIR/SWIR/MWIR/ LWIR detectors or broadband non selective detectors). All main types of infrared detectors can be tested: photonic detectors: photovoltaic/photoreconductive, cooled/non-coooled, thermal detectors, pyroelectric detectors etc.
-
Product
Flexible Temperature Testing & Thermal Cycling
TA-5000B Series
-
MPI Thermal manufactures a variety of compact temperature chamber solutions for electronics and material test and thermal conditioning. An array of standard and custom design high-performance Clamshell styles and other configurations and custom dimensions and sizes are available. MPI ThermalAir Systems compact chamber thermal products are available to meet your test application needs.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
CO Carbon Monoxide Probe
HD320A2
-
HD320A2 is a probe to be used with the HD32.1 Thermal Comfort data logger.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
Low Thermal Input Connector
34104A
-
Design custom input connections on your 34420A Micro Ohm Meter with this mating connector
-
Product
Environmental Testers
-
Axi'An Beicheng Electronics Co., LTD.
Environmental Testers by RuoShui: digital thermometers, thermal imaging analyzer, infrared thermal imager, thermo-hygrometer, nicety meters, rain gauge, coating thickness gauges, combustible gas detector and monitor, carbon monoxide monitor, digital anemometer, vibrometer meters, storboscope tachometers, digital tachometer, combustible gas detectors, 4 in 1 gas detector, digital refractometer, wood moisture meter, lux meter, sound level meter, sound meter, and more.
-
Product
Thermal Controlled Chucks & Plates
TOP Cool
-
Mechanical Devices newest innovation in thermal testing. Each TP system contains a thermal chuck or thermal plate and a self-contained thermal control unit.The TP chuck and platforms is a breakthrough product that introduced the use of refrigerant for active cooling & heating of wafers and other components with no need of chiller, CDA, or consumable and expensive refrigerants such as liquid nitrogen and liquid carbon dioxide. It can be a perfect replacement system in the industry for uncompromising thermal and mechanical performance with a temperature ranging from -60 to +220°C.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
Product
Terminal Block For 34921A And L4421A Multiplexer
34921T
Terminal Block
Offers a built-in thermocouple reference junction that helps minimize errors due to thermal offset
-
Product
Environmental Testing
-
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
Product
OM Thermal Stress System
-
Conductor Analysis Technologies, Inc
The OM Thermal Stress System is a cost-effective performance based reliability test methodology which performs convection reflow assembly simulation and air-to-air thermal cycling. The methodology is utilized by both the IPC PCQR and the IPC 6012-QLM programs. OM systems are available for sale or lease, and test services are provided from both CAT and our service partners.
-
Product
Pyrometer with Spotfinder
thermoMETER TIM 8
-
The thermoMETER TIM 8 combines the advantages of a robust pyrometer with a thermal imaging camera. Due to its extremely compact size, it can also be integrated into machines and production lines. The spotfinder function enables precise temperature measurements with automatic sensor adjustment. In addition, remote focusing of the lens is possible via a motorized focus. This intelligent spotfinder pyrometer is used in automation, machine building and plant monitoring.
-
Product
Differential Interferometer
10715A
-
The Keysight 10715A Differential Interferometer performs differential measurements between the supplied reference mirror and a measurement plane mirror. It provides exceptional long term stability. The 10715A minimizes dead path, and, because the entire optical path through the interferometer is common mode, it eliminates thermal drift in measurements. The resolution of the measurement is twice that of a linear or single-beam interferometer.
-
Product
Cryogenic ICP® Accelerometers
-
Cryogenic ICP® accelerometers are specifically designed to operate at temperatures below the typical -65 ºF (-54 ºC) temperature limit of most voltage mode sensors. The use of specialized, built-in, cryogenic circuitry and quartz shear sensing technology promote survivability in demanding environments such as liquid nitrogen. Each sensor is hermetically sealed and individually tested to determine the thermal coefficient of sensitivity at -320 ºF (-196 ºC) ensuring reliable operation and accurate measurements. These sensors have been successfully used in the presence of liquid helium during structural testing of rocket boosters.
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30003-K
-
Breakout board for the MAX31855K digital thermocouple interface ICs by Maxim. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws.
-
Product
ALD For Research & Development
-
Veeco’s atomic layer deposition research systems are designed by ALD scientists and built for maximum experimental flexibility and value. With universal precursor delivery systems, you can use solid, liquid or gas chemistries in any precursor port. There are many options to choose from including ozone generators, in-situ monitoring and various configurations. As always, our team of ALD scientists are ready to answer your recipe development and film characterization questions. Over 2500 published academic papers feature research performed on our Savannah® thermal ALD system and Fiji® plasma ALD system.
-
Product
Fast Temperature Shift
CherryTemp
-
CherryTemp is a temperature controller based on two independent Peltier channels, allowing for very accurate temperature control and ultra-fast shifts from 5°C to 45°C. A thermalization liquid circulates from a reservoir to the heat exchangers (heating/cooling Peltier elements) where it is thermalized to a target temperature. Once thermalized, this liquid can be quickly injected to a microfluidic device (CherryTemp chip) mounted near the sample. Because of the small thermal mass (the distance between the microfluidic chip and the sample), the temperature transfer is very fast (less than 10 seconds) and of unprecedented accuracy due to a feedback loop control of the room temperature and the heat-sink played by immersion objective lenses.
-
Product
Quality Control for more Precision in Press Hardening
PRESS-CHECK
-
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
Product
Abrams Driver’s Vision Enhancer
DVE-A
-
The Abrams Driver’s Vision Enhancer (DVE-A) was developed specifically for the Abrams Main Battle Tank allowing for the driver to egress safely by using the quick disconnect bracket assembly. Combat proven and fielded in over 2000 US Army Abrams Main Battle Tanks to date, the DVE-A offers the latest in long wave thermal imaging capabilities.
-
Product
AC Current Shunts
-
AC Current Shunts feature low uncertainty (high accuracy), low temperature coefficients and excellent stability. These shunts are purely resistive with extremely small values of reactance. The 7340 shunts may be used over a wide frequency range from DC to 100 kHz and are optimized for use with thermal converters.
-
Product
Silicon Detectors
-
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
Product
MAX31855 T-Type Thermocouple Sensor Breakout
SEN-30001-T
-
Breakout board for the MAX31855T digital thermocouple interface IC. Measured temperature range is -270C-400C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
Echotrac MKIII
-
Teledyne Marine Odom Hydrographic
The Echotrac MKIII is the only sounder on the market offering you the choice of either a high resolution thermal paper recorder or a full-sized high bright color LCD chart in interchangeable module format. Both high and low channels feature frequency agility, enabling the operator to precisely match the transceiver to almost any existing transducer. This ability minimizes near-surface noise caused by transducer ringing while increasing echo return strength. The MKIII is capable of both shallow and deep water operations and features unsurpassed interfacing flexibility with four serial ports and high speed Ethernet capability for maximum efficiency.
-
Product
Thermal Imager with App
testo 868
-
With the testo 868 thermal imager, we have developed a thermal imager which makes work quicker and easier without foregoing professional thermal imaging technology. You can generate error-free and objectively comparable infrared images using its handy functions. The IFOV warner, testo -Assist and testo ScaleAssist mean you can avoid measurement errors and not only effortlessly achieve optimum setting of emissivity () and reflected temperature (RTC) for building thermography, but also of colour scale.
-
Product
Thermal Quad Scanner
-
Thermal Quad Scanner has the Highest Isolation of any 4-Terminal Scanner and operates at up to 1000V. With a Guildline model 6664C scanner and software, hard-to-make high ohm measurements (up to 100 GΩ) can be automated and scheduled at any time that is convenient to the metrologists, even at night and over the weekends.
-
Product
Reliability Testing Services
-
Innovative Circuits Engineering, inc
Our Reliability Testing Services make it possible for us to work with many different customers who manufacture devices that need tests such as pressure pot, temp cycle and more.The focus of our reliability testing lab is to provide our customers with an array of services and tests that fulfill all of their reliability testing needs. Whether you need preconditioning, thermal shock, pressure pot, or many other reliability testing needs, we are happy to be of service.
-
Product
Thermal Imager with App
testo 872
-
The testo 872 thermal imager is ideally suited for professional industrial and building thermography - at the same time it ensures your work is both quick and easy. It is versatile to use, for example in industrial and mechanical maintenance or for detecting structural defects. You can generate error-free and objectively comparable infrared images using its handy functions. The IFOV warner, testo -Assist and testo ScaleAssist mean you can avoid measurement errors and not only effortlessly achieve optimum setting of emissivity () and reflected temperature (RTC) for building thermography, but also of thermal image scale.
