Calibrators
ascertain instrument graduation deviation and rectify to precision known values.
See Also: Calibration, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
Product
High-Voltage Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
Product
Precision Calibrated Noise Sources
-
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
Product
Stat Guardian Plus Constant Monitor
-
ests person, wriststrap, and matLED and buzzerNIST calibration includedWorks with single wire capacitance wriststrapsCE markCan be calibrated110v AC suppliedProduct conforms to the ESD S.20.20 spec standardsGround dock included
-
Product
Optical Oxygen Sensors
-
PST offer a range of factory calibrated optical oxygen sensors which measure trace and ambient oxygen levels using luminescence-based optical technology.The patented technology allows the range of sensors to produce low power operation, while offering a long lifetime.
-
Product
Colorimeter
Model CA-600
-
Teledyne Analytical Instruments
The CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer. Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.
-
Product
Paramagnetic O2 Analyzer Optional CO2 Sensor
Model T802
-
Teledyne Advanced Pollution Instrumentation
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.
-
Product
Frequency Extension Heads for Vector Network Analyzers
FEV
-
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
Product
Potentiometers
Accu-tach / Accu-dial
-
Programmable potentiometers with LCD display and feedback display in user units.• Replaces traditional potentiometers• Precise process control and feedback• Reduces costly downtime and product waste• Easy to install and calibrate• Tough ABS plastic enclosure - NEMA 4 rated• Small footprint - only 1.95" x 3.10"
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Instrument Transformer
CT & PT Test Equipment
-
Measurements International Ltd.
Calibration of Voltage and Current Transformers from a Single Instrument, Calibration of Instrument Transformers with Different Rated Ratios Using One Single Reference Standard, Calibration of Voltage Transformers (VT) up to 800 kV When Used with MI 2500 Series of HV Dividers and Standard Capacitors, Calibration of Current Transformers (CT) Up to 10000 A When Used With MI 7020 and/or 7200 Series of Precision Current Transformers and/or Current Comparators, Test Frequency from 15 Hz to 100 Hz70.
-
-
Product
1.533 Μm Frequency-Locked Laser
-
Thorlabs' LLD1530 Frequency-Locked Laser is a narrow linewidth, DFB-laser-diode-based, turnkey system with a vacuum emission wavelength of 1532.8323 nm and a high SMSR of at least 35 dB. The laser frequency is actively stabilized to a National Institute of Standards and Technology (NIST)-traceable molecular transition of acetylene and has an absolute accuracy at start-up that is better than ±25 MHz. The emission frequency immediately after start-up is then maintained with a ±25 MHz stability, providing an overall frequency accuracy of ±50 MHz. The LLD1530 is an accurate frequency reference designed to provide low-noise laser emission with excellent frequency stability, accuracy, and precision immediately at start-up. This source is ideal for use in demanding FTIR instrumentation, instrument calibration, gas sensing, and coherent telecommunications applications.
-
Product
Spectrum Marker Generator
NSG-2
-
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
Product
Calibration Measurement
-
The process of comparing a measuring instrument's readings to a known, more accurate standard to detect and correct errors.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Microphone Calibration Workstation
9350C
-
The Precision Acoustic Calibration Workstation Model 9350C is an accurate, turnkey, automated PC-based system that features cost-effective calibration of ¼", ½" and 1" microphone cartridges (open-circuit sensitivity), microphone cartridges with preamplifiers (closed-circuit sensitivity) and microphone Frequency Response Function.
-
Product
Spectral Radiant Flux / Luminous Flux Calibration Standards
-
Standard lamps calibrated in luminous flux and spectral radiant flux. Versions with 2-Pi and 4-Pi emission characteristics. Traceable calibrations in the wavelength range from 200 nm to 2500 nm.
-
Product
Optical Radiation Meter
ORM400
-
The ORM400 Optical Radiation Meter has a USB 2.0 interface and is supplied with powerful calibration features and data display functions. It is ideally suited to display the measurements from the DH400 range of detectors as well as third party current generating detectors.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8493A
Attenuator
The Keysight 8493A coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Frequency Meter, 3.7 to 12.5 GHz
537A
Frequency Counter
The Keysight 537A direct-reading frequency meter measures frequencies from 3.7 to 12.5 GHz quickly and accurately. Its long scale length and numerous calibration marks provide high resolution. This is particularly useful when measuring frequency differences or small frequency changes. Frequency is read directly in GHz so interpolation or charts are not required.
-
Product
Helium Leak Detectors
-
Agilent’s range of leak detection solutions ensure the safety, security, and consistent performance of research, vacuum, and industrial process systems. Our Helium Leak Detector (HLD), PHD-4 sniffer and C15 component leak detector are rugged, precise, and easy-to-use instruments that accurately and efficiently detect leaks in an array of industrial applications. For clean research applications, HLD configurations employ clean, dry, quiet scroll vacuum pumps. Our leak detectors feature automated start-up and calibration for maximum productivity, built in application set-ups, and an array of accessories to make any leak detection process simple.
-
Product
Gas Monitor
ULTIMA® X5000
-
The ULTIMA® X5000 Gas Monitor is the future of gas detection for oxygen, toxic and combustible gases. MSA XCell® gas sensors with TruCal® technology offer calibration cycles up to 24 months (local calibration respected).
-
Product
Data logger for Temperature Humidity and Differential Pressure
DSR-THDP
-
Simultaneously measures and logs temperature, humidity and differential pressure Support on-line linear calibration and zero setting Customized differential pressure measuring range between 0 and 1000Pa Suitable for pharmaceutical workshops, electronic production, precision machinery and other applications
-
Product
AmeTrim
-
AMETEK Sensors, Test & Calibration
Using the external reference sensors on the temperature calibrators or indicators to measure the true temperature, AmeTrim can perform a fully automatic calibration and adjustment of the internal sensor.
-
Product
RF Ports Alignment Software
-
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
Product
Pitot / Static Tester for Laboratories and Workshops
ADSE 741
-
The ADSE 741 is a complete high performance three channel Ps, Pt and AoA stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, pneumatic AoA (Angle of Attack) indicators, MACH-meter, air data computers, specific probes and sensors.The high precision embedded sensors enable the ADSE 741 to be used as a pressure standard.The user interface is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
Product
FieldFox Handheld Microwave Analyzer, 9 GHz
N9915A
-
9 GHz max frequency Carry the world's most integrated handheld & micro; W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
T3SP Time Domain Reflectometers
T3SP Series
-
Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.
-
Product
Manual Semiconductor Metrology System
-
Front USB port enables easy storage of measurements and other data to flash drivesMTI Instruments’ Proprietary Capacitance Circuitry for Outstanding Accuracy and DependabilityNon-contact measurements76-300 mm diameter wafer rangeOptional wafer measurement ringsWafer stops for exact centeringEthernet interfaceFull remote control software (Windows compatible)Optional calibration wafers
-
Product
Calibration Foils Sets
990
-
The Elcometer 990 Calibration Foil Sets are ideal for use in the laboratory, on the production line or on site.
