Product

Shield Level / Pathloss Equipment

SG1000B/PR1000A

-

Praxsym

SG1000B/PR1000A - Praxsym

The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.​To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.

Product

Pre- Locator

CFL PL3

-

Scope T&M Pvt, Ltd.

CFL PL3 - Scope T&M Pvt, Ltd.

CFL PL3, new generation Cable Fault Pre-Locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault with accuracy.

Product

24-Channel Digital I/O With Digital Integration Features On PCI Express Mini Card

mPCIe-DIO-24A

-

Acces I/O Products, Inc.

mPCIe-DIO-24A - Acces I/O Products, Inc.

The mPCIe-DIO-24A is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.

Product

Portable PD Analyzer

AQUILA

-

Doble Engineering

AQUILA - Doble Engineering

A compact and portable Partial Discharge acquisition unit, which allows to detect and analyze partial discharge activities in all electrical assets: from power cables to transformers, rotating machines and switchgears, together with the right combination of sensors and accessories. AQUILA comes with a full range of options, ideal for field testing.

Product

Solder Cup Connector Kit

Y1139A

-

Keysight Technologies

Y1139A - Keysight Technologies

Used to build custom cables for 34921/23/25/31/32/33/37/38 –50-pin Dsub female – 125 V

Product

Live PD Emulation

-

Sifos Technologies, Inc.

Sifos Technologies, Inc.

Flexibly Mimic Class 0 to 4 Powered Device Per PSA/PSL-3000 Test Port. Configure up to 192 Simultaneous IEEE 802.3 PD’s. User-Defined Class 0 - 4 Powered Device Modeling with or without Cable Loss. Emulate 802.3at PoE-LLDP Negotiations and Power Adjustments. Monitor Multi-Port Live Emulation Status. Available to PSA-3000 and PSL-3000 Platforms as optional license feature.

Product

3U VPX 5 Slot Power & Ground 10G Pass Through

101VPX305P-9X21R

-

ELMA Electronic, Inc.

101VPX305P-9X21R - ELMA Electronic, Inc.

Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.

Product

Standard Shackle Load Cell

SS-3.0

-

Dynamic Load Monitoring Ltd.

SS-3.0 - Dynamic Load Monitoring Ltd.

The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.

Product

Single-Phase Transformer Winding Resistance Meters

RMO-TD Series

-

IBEKO Power AB

RMO-TD Series - IBEKO Power AB

Using the most advanced switch-mode technology available today, the RMO-TD series is ideal for winding resistance measurements of inductive objects. Transformer resistance meters and tap changer analyzers are perfect for testing:transformer windings (power transformers, distribution, autotransformers),all types of tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.In addition, transformer demagnetization can also be done with all RMO-TD instruments.The RMO-TD series contains 3 models, with maximal test currents from 25 A (RMO25TD) to 60 A (RMO60TD).The three independent voltage sense channels enable testing of three windings in series. This enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.All RMO-TD transformer resistance meters have a built-in tap changer control unit. It enables remote control of on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, DV-Win software is included which can be programmed to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.

Product

Temperature and Humidity Probe

T0211-2

-

COMET SYSTEM, s.r.o.

T0211-2 - COMET SYSTEM, s.r.o.

Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

Sensor Cables

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® manufactures a wide variety of cable assemblies that will mate to different sensor types, signal conditioners and data acquisition systems. Cables are an important part of every measurement system. PCB carefully selects different raw cable types from trusted suppliers and time is taken to design cable to connector interfaces that will be reliable. All cable assemblies are produced at one of PCB's manufacturing locations to tightly controlled assembly procedures that ensure durability in various applications and environments.

Product

Pre- Locator

CFL PL4

-

Scope T&M Pvt, Ltd.

CFL PL4 - Scope T&M Pvt, Ltd.

CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.

Product

Pin-Pointing System

Protrac®

-

BAUR

Protrac® - BAUR

As precise as pre-location is, it will never be able to recognise the deviations of a cable route in the ground. These can only be detected by precise pin-pointing. With its protrac®, BAUR offers different solutions that combine acoustic and electro-magnetic cable fault pin-pointing, sheath fault location and tracing in a single system.

Product

SAS

-

SCHILLER AUTOMATION GmbH & Co. KG

SCHILLER AUTOMATION GmbH & Co. KG

The Gen4 Mini-SAS HD adapter kit will facilitate compliance testing for SAS-4 host, device, and cable. The left and right-hand version plug adapters are designed to test side-by-side.

Product

PCB IMID01, 100 mV/g, IEPE, 2-Pin, Accelerometer, Industrial Vibration Sensor

784175-01

-

NI

784175-01 - NI

The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.

Product

Isolated SCIM5B Analog Signal Conditioning Products

SCIM5B

-

Bee Instruments

SCIM5B - Bee Instruments

BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.

Product

SparkFun FTDI Basic Breakout

3.3V

-

SparkFun Electronics

3.3V - SparkFun Electronics

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.

Product

HDMI Converter

B-SDI-HDMI

-

QuestTel

B-SDI-HDMI - QuestTel

QuestTel''s 3G/HD/SD-SDI to HDMI mini Converter adopts Video Through Technology, delivering clear and vivid pictures on your HDMI displays. Supports auto resolution detection of 3G-SDI, HD-SDI and SD-SDI. Embedded SDI/HD-SDI audio is supported in the HDMI output allowing a convenient single cable audio/video connection. Supports resolutions up to 1080p.

Product

Thermocouple Probes

Type T

-

ThermoWorks

Type T - ThermoWorks

No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.

Product

DC/DC Converters & DC/AC Inverters

-

Phoenix Contact GmbH & Co. KG

Phoenix Contact GmbH & Co. KG

DC/DC converters and DC/AC inverters are available for voltage conversion. With our DC/DC converters, you stabilize DC voltage, refresh the voltage at the end of long cables, and thus avoid malfunctions in your applications. Use our DC/AC inverter to convert direct current into alternating current.

Product

RF Spectrum Power Meter

SPM-50

-

ShinewayTech

SPM-50 - ShinewayTech

SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.