Parametric Test
determine whether a DUT's electrical characteristics meet specification.
-
product
DC Parametric Test System with Curve Trace
DC3
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
product
256 Channel Power Supply
IDPS750
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
TSCOE4 Operator Interface Software Module
The TSCOE4 Operator Interface provides a graphical user interface for the operator or the implementer in a production environment. It permits selecting the test sequence and supports parametrization of the test. During the test sequence, the current measurement values are displayed in relation to the relevant limits and the pass/fail evaluations for each individual test. After completion of the test sequence, the global test result is visualized.In addition, there are online statistics available to the user, which show the measurement value distribution within the current batch.The editor which is supplied with the product makes it possible to adapt the user interface language to any new deployment location. Several languages – German, English and Chinese – have already been implemented and are available out of the box.
-
product
Universal Launcher Test Set
TS-217
The TS-217 is an I-level and Depot-level Universal Launcher test set supporting fighter aircraft launchers including the LAU-127, LAU-128, and LAU-129 (AMRAAM), LAU-117 and LAU-88 (Maverick), and LAU-7 (Sidewinder) missile launchers, launcher electronic assemblies, launcher power supplies, and circuit cards. The TS-217 is also used as a depot-level tester for F-18 armament including launchers (LAU-127, LAU-7, LAU-115, and LAU-116), bomb racks (BRU-32), and aircraft pylons (SUU-62 and SUU-63). Additionally, the TS-217 supports MAU-169 Paveway kits, subassemblies, and circuit cards. The TS-217 performs full parametric functional testing as well as troubleshooting to the faulty LRU (I-Level configuration) and SRU (Depot-Level configuration). The TS-217 can be used as an I-Level tester or as a Depot / Acceptance tester for launcher subassemblies.
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, Direct Y Access, 6 Analog Buses
65-221-012
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
RF Bias Burn-In System
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
product
Multi-Wafer Test & Burn-in System
FOX-XP
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
product
Probe Card
VC20E Series
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
product
LXI Reed Relay Matrix - Single 32x32 Plugin, No Direct Y Access, 1 Analog Bus
65-227-101
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Test Contactor/Probe Head
Atlas
QuadTech™ probe solution with cruciform tip strength that stands up to lateral force without bending, plus an enhanced compliance window to accommodate package stack height tolerance.Atlas™ test contactor offers electrical performance that allows the customer to test to the true performance of the device. Atlas WLCSP test contactors achieve mechanical reliability with a rigid “cruciform” tip applied to Cohu’s QuadTech flat probe technology. The Atlas offers a short electrical path, with lower capacitance and inductance, that is ideal for functional and AC parametric testing of WLCSP devices that require high system bandwidth and throughput gains in large multisite test applications.
-
product
DDR4 Parametric Test Reference Solution
Keysight's DDR4 parametric test reference solution helps verify the signal integrity of DDR4 memory designs according to JEDEC specifications.
-
product
Probe Card
VC43™/VC43EAF™
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
product
Combination Board Tester
ATE QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
product
LXI Reed Relay Matrix - Single 32x16 Plugin, No Direct Y Access, 3 Analog Buses
65-225-102
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
64 MB RAM Tester
IST-6500
IST Information Scan Technology, Inc.
The IST-6500 is a low cost, fully programmable tester for functional and parametric testing of DRAM, SRAM, VRAM, and SIMM devices up to 144 bits wide and 64 MB in size. The 6500 offers four different ways to automatically measure the access time of these devices from 2ns to 160ns with a resolution of 2ns. The DRAM timing parameters are programmable at the resolution of 1ns to allow for testing DRAM, SIMM, or VRAM at their required operating speeds, thus providing real time test conditions.
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
Probe Cards
Ceramic Blades
SV TCL offers a variety of ceramic blades and blade probe cards. We have patented ceramic microstrip blade probes available in low leakage and low capacitance for optimal signal transference, while SV TCL's blade cards are ideal for parametric and RF testing.
-
product
LXI Reed Relay Matrix - Single 32x32 Plugin, Direct Y Access, 1 Analog Bus
65-227-001
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
NI Automated Test Software Suite
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
product
Infotainment Test for Automotive Applications
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Test Management Software
ActivATE™
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
product
Application Software for Electronic Test & Instrumentation
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.





























