-
product
Non-steady-state probe for thermal conductivity measurement
TP02
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
product
SparkFun Pulsed Radar Breakout
A111
Does your project require high-precision, cutting-edge distance measurement? Or maybe speed, motion, or gesture-sensing? We're not talking about simple ultrasonic or even infrared here, but 60GHz radar! Well say hello to the SparkFun A111 Pulsed Radar Breakout! The A111 is a single-chip solution for pulsed coherent radar (PCR) and comes complete with an integrated antenna and an SPI interface capable of clock speeds of up to 50MHz. Though the A111's primary use case is distance-sensing, it also supports applications in gesture, motion, material, and speed-detection at distances of up to two meters.
-
product
GSM Controller
SCOM-100
Infinite Industrial Informatics Lt
SCOM-100 is a powerful GSM controller for alerting and remote control using SMS. The rail mount unit incorporates a Quad Band GSM/GPRS modem, 2 analog inputs, 4 digital inputs with retentive pulse counting capability, 4 power relay outputs and a serial RS-232 port.
-
product
NI-9402, LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module
779987-01
LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module - The NI‑9402 is a per‑channel configurable digital I/O interface for input or output. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9402 for … implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
High Voltage Film Capacitors (Axial Leads)
STVHF/STVHE-A
For High Pulse / High Energy Discharge applications with low discharge repetition rate, please tell more about your application. We might have a suggestion.
-
product
Laser Distance Meters
Sends a pulse of laser light to the target and measures the time it takes for the reflection to return
-
product
LAN Cable Tester
LAN-1
The LAN-1 Cable Tester is designed for testing opens, shorts and miswired cable installations. It is designed to work with various data cables and connectors. This cable tester provides a quick go / no-go LED display of the wiring and connection of item under test. You can either step through the test cable wiring one at a time or have the unit automatically pulse through the pin-outs and display the results.
-
product
Ethernet Connector Modules
With an extensive line of high-quality ethernet connector modules in our product lineup, Pulse Electronics Networking BU can easily supply the parts you need to develop your next ethernet product.
-
product
Femtosecond Terahertz Spectrometer
Pacifica
Terahertz spectroscopy and microscopy are becoming a powerful tool in biology, medicine, semiconductor physics and in many applicaitons. Designed for obtaining THz spectra by using of THz pulses generated by femtosecond laser in oriented ZnTe crystal.
-
product
Saluki S1433 Series Handheld Signal Generator (1MHz to max. 50GHz)
Saluki S1433 series signal generator is a hand-held instrument specially designed for field testing. It has the functions of CW signal output, FM/AM/Pulse modulation, large dynamic range amplitude adjustment, step/list sweep etc. The integrated design of 8.4-inch large capacitive touch screen is convenient for users’ operation.
-
product
Digital Current Integrator
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
product
Real-Time Pulse Detection Firmware
FWPD
The core challenge in pulse detection is to design a system for random events. The Teledyne SP Devices’s firmware option FWPD, for the ADQ14 and ADQ7, is tailored to detected and analyze pulses in demanding measurement applications where the properties of the pulses (such as timing or length) are not known in advance.
-
product
High Speed Free Space Optical Detectors
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
product
Incremental Encoders
Versatile, compact and flexible – Incremental encodersIncremental encoders are used when retention of absolute position upon power loss is not required. These encoders provide information about the position, angle and number of revolutions. The number of lines per revolution determines the resolution. The current position can be determined by counting these pulses from a reference point. Upon activating the machine, a reference run to the reference point is required to determine the absolute position of the encoder.
-
product
Energy Analyser
DUCA-LCD
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
product
Activity Detection Unit
DG009-M1
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
product
Interface Module
MC
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
product
Multi-channel S-band Klystron 2.45 GHz / 5 MW
Insight Product Co. 's multi-channel S-band, 2.45 GHz, klystron provides up to 5.0 MW of output pulse power.
-
product
High Voltage Pulse Generators
Berkeley Nucleonics Corporation
Designed to provide precision control over the output waveform to enable process optimization for research and industrial customers.
-
product
Millimeter Wave Spectrum Analyzer
Insight Product Co. offers the spectrum analyzer for frequency measurements of millimeter wave generators of continuous or pulsed signals. The spectrum analyzer can be ordered to cover a complete millimeter wave frequency band: 35-53 GHz; 53-78 GHz; 78-118 GHz; or 118-178 GHz and offer exceptional spectral resolution of 1-5 kHz.
-
product
2-18GHz Switch Multiplexer
SA219
Teledyne Defence & Space’s (TDS) patented designs have produced many different types of filters incorporating switches. These are all generally wideband for Electronic Warfare applications and enable the control of the frequency spectrum into any given system. These units, also known as Switch Multiplexers, are configured with a single or multiple inputs to single or multiple filtered outputs.As an example, the SA002 features 8 channels switchable over the frequency range 2-18 GHz while the SA004 offers 17 channels over the 0.5-18GHz bandwidth. Each provides the user with a fast, flexible, filter network capable of providing different band-pass or band-stop responses on a pulse-by-pulse basis in dense signal environments.
-
product
1 / 2 / 3 MHz Multi-Waveform Signal Generator
MSG1M / MSG2M / MSG3M
- Wide frequency range- Sine, triangle, square, ramp, pulse, TTL (Sync) & DC outputs- Low distortion high resolution on low frequency output attenuation up to 80dB- Variable DC offset control- Four digit digital display with frequency indication in Hz, KHz, MHz/Amplitude display
-
product
KATANA & PILAS Pulsed Diode Lasers
With external trigger functionality, nano- to picosecond pulse duration, and a wide range of wavelengths, the KATANA & PILAS series are our most versatile offering.
-
product
SMD LED Aging Test Machine
CX-6100
Shenzhen Chuangxin Instruments Co., Ltd.
Designed to measure the aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.• 150 separate constant current supply• Aging functions: constant current, impact pulse, on-off mode• Range of forward voltage(VF): 5.0V• Range of forward current(IF):1) constant current: 0-100.0mA2) Impact pulse: 0-200.0mA• Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99%
-
product
Illumination
*Illumination units for contour and position verification*External LED illumination for contour / pattern match sensors*Permanent light or pulse operation*White light, red light and infrared versions*Compact and robust housing
-
product
Dual Digital Multichannel Analyzer
780 MCA Family
The 780 MCA family integrates advanced firmware algorithms operating Digital Pulse Processing for Pulse Height Analysis (PHA). The processing algorithms can be easily adapted to different detectors and application ensuring effective data analysis even at high count rates. It provides advanced tools for configuring baseline restoration, pile-up rejection. Thanks to the two input simultaneous acquisition, the modules are able to manage coincidence and anti-coincidence logic between detectors, allowing the user, for example, to easily take advantage of background rejection or anti-Compton techniques. These MCAs may provide at the same time energy, time stamp and the digitized pulse in a configurable time window (e.g. including the rising edge region) in order to perform further online analysis. Acquisition settings and basic mathematical analysis are performed through the CoMPASS and MC2Analyzer software, providing energy spectra with up to 16k channels, which can be exported and imported in ASCII or N42.42 compliant files. CAEN further provides drivers for the supported communication interfaces; configuration software tools, C and LabVIEW libraries (CAENComm, CAENDigitzer, CAENDPP), demo applications and utilities.
-
product
Multi-Channel Vector Signal Generators
875
Berkeley Nucleonics Corporation
The Model 875 is an ultra-fast-switching vector-modulated signal source covering a continuous frequency range from 10 MHz to 40 GHz. The Model 875 offers switching speeds as fast as to 200ns, enables ultrafast CW frequency sweeps, chirping, intra-pulse modulation and pulse shaping, all with very low phase noise. A high-performance internal I/Q modulator enables customized modulation waveforms and supports dedicated modulation schemes such as avionics modulations. This newly engineered design couples extremely deep memory and wideband capabilities - making complex modulation affordable and easy to program.
-
product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
product
Advanced 4-CH Encoder Card with High-speed Triggering Function
PCI-8124-C
PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output. For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function. For position compare, PCI-8124-C provides two method: linear function or variable interval. PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.
-
product
Closed Loop Hall AC/DC Current Sensor
CYHCS-D8
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current in the carrying conductor.
