Beam Load Cells
use the deformation of a spring to measure the strain force applied to it. Also known as: Bending Load Cells
See Also: Beam
-
-
Product
UV-NIR Beam Profiler
CinCam
-
CINOGY Technologies CinCam is optimized to provide excellent sensitivity from the UV to NIR spectral range involving CCD/CMOS/InGaAs technologies. Thanks to its high resolution and its small pixel size, the CinCam ensures the highest accuracy in laser beam analysis of cw and pulsed laser systems. The plug and play design facilitates easy and flexible adaption to standard optical components.
-
Product
Phantom Load Test Set
-
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Taper System, CCD Beam Imaging Camera
TaperCamD series
-
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
Product
Torque Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
Product
130 AMP Battery Load Tester
MD4370
-
Compact, ergonomically designed tester determines a battery's charge and tests batteries, starting, and charging systems.Powerful 130 amp load capacity provides more accurate test results.Uniquely designed clamps assure a positive connection on any style battery.
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Sometimes you may need additional loading for abnormal testing (i.e. overload test). Other times, you may need additional loading to simulate worst case normal operation conditions (i.e. input test, temperature test). No matter what your application, we have the loading device to fit your needs! TECH NOTE: Be sure to request our outline titled "Selecting Loads" for assistance in determining the proper rated device for your application.
-
Product
Ultra Precision Mini Load Cell Universal/ Tension or Compression
MDB SERIES
-
The MDB Series Load Cells was designed to help fill the growing need for a greater selection of high accuracy load cells for use in space limited applications. The anodized aluminum MDB's are compliant in tension and compression, therefore, a good choice for in line through zero applications, as well as single direction tension or compression. Applications may include load feedback for process control, low capacity tensile testing machines, robotics, or designed into your product. Give us a call, we would be pleased to discuss your application requirements.
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
Product
Laser Diode Collimators, 520nm - 785nm, Elliptical Beam
-
The Optoelectronics Company Ltd
Custom lasing wavelengths and power options are available. Both standard and custom configurations provide OEMs, end-users and systems integrators with complete, cost-effective laser solutions.
-
Product
Unclamped Inductive Load Tester
ITC55100STD
-
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
4% Beam Splitter
10725B
-
The 10725B 4% beam splitter, designed for beam diameters of 9 mm or less, reflects 4% of the total incoming laser beam and transmits 96% straight through. This optic is without housing and requires a user-supplied mount.
-
Product
Unclamped Inductive Load Tester
ITC55600C
-
Model ITC55350 is the high current (600A) version of theITC55100 tester. The ITC55350 performs the same testsas the ITC55100 and includes many features that improvetesting accuracy, test results collection, test resultsviewing, and multiple tester networking
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
Economical Load and Force Measurement
ELF
-
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
Product
Wideband Active Load Pull
S94572B
-
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
Product
Coaxial Loads
-
Loads are supplied standard with N connectors, which are recommended above 500 MHz.
-
Product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
-
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
Product
Cold Atomic Beam System
-
Detailed description of item: Complete cold atomic beam sources for alkaline-earth precision experiments and atomic devices. Small chambers with patented permanent-magnet Zeeman slowers and in-vacuum 2D MOT optics allow high flux with low outgassing and no thermal beam flux at the cold atom port, which provides a CF-133 connection to customer vacuum chamber. Advanced thermal design of the effusion oven allows long-lifetime operation at minimal heating power, with no water cooling. An integrated low-outgassing hot window is provided for coupling of on-axis Zeeman cooling light. Ion and getter pumps integrated into the chamber manage outgassing from the oven at temperatures up to 520 °C. Operating baseline pressures below 1×10-11 mbar can be attained in the customer’s downstream cold atom (typically 3D MOT) science chamber, with suitable pumping speed provided at the differentially-pumped cold beam output port.
-
Product
Test Cell Measurement
-
Accurate Technologies’ long history in powertrain development provided insight into the day-to-day issues that were occurring during engine testing at a time when electronic devices were being introduced to monitor performance instead of traditional mechanical means. Outside of the harsh physical environments, devices used in these applications need to perform difficult high-voltage signal conditioning and high-speed synchronous pulse processing. ATI developed unique products that satisfy specific test cell or dynamometer challenges. These highly accurate products measure engine timing (IGTM) or speed (SmartTach) in convenient ways to provide information that otherwise may not be available.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
-
-
Product
PowerSync Programmable Load
PSL-3424M
-
Sifos Technologies offers one-box platforms to facilitate analysis of Power Sourcing Equipment (PSE) behaviors. The PSL-3424M is Sifos’ lowest cost, multi-port PSE test instrument supporting PSE loading and power stressing. Depending upon configuration, up to 12 ports can simultaneously load over 1200 combined watts, emulating 802.3at and 802.3bt single signature PD’s advertising Class 0 to Class 8. With per-slot multiplexing, up to 24 PSE ports can be connected enabling automated test strategies covering 24, 16, or 8 port PSE’s.
-
Product
Cells and Electrodes
-
Electrochemical cells are designed to their special purpose. The method, the matter and their reactions as well as the environmental conditions define the limitations and demands for electrochemical cells and the electrodes. Standard corrosion testing cells may have a large volume, since corrosion products shall not change the solution grossly during the test. On the other hand, it may be valuable to collect corrosion products - then a very small volume is desired ("eluation cell"). Special corrosion tests for pitting reqiure a setup where undesired crevice corrosion is excluded ("Avesta cell" , "Quarfort Cell" or "Flushed port cell". Or you want to investigate in crevice corrosion, then the cell design should meet such conditions. Have a look to the variety of cells shown here, and call us if you have a special task where a fresh design is required.
-
Product
Single Point Aluminium Load Cell
EST-4
-
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
