-
product
5.5mm (0.22") Digit Height
DPM 1AS-BL
The DPM 1AS-BL is an ultra-miniature 3 digit LCD voltmeter with 5.5mm (0.22") digit height and LED backlighting. It features a negative rail generator which enables the meter to measure a signal referenced to its own power supply GND.
-
product
- Optical / RF Converter
OPT 80
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
product
Analog Power Supply
Type NPS-2412
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
product
Bench/System DC Power Supply With PowerFlex Or PowerFlex+ Regulation
QPX Series
Wide range of voltage/current combinationsUp to 80V and up to 50A within the same power envelopeLow output ripple and noise of <3mV rms at full powerHigh setting resolution of 1mVAnalogue control interfaces for voltage and currentBench or rack mounting, front and rear terminalsUSB and LAN (LXI) interfaces with GPIB optional (QPX600DP, QPX1200SP and QPX750SP)
-
product
Voltage Protection
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
product
High Voltage Power Supplies
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
product
VXI Mainframes & Controllers
The Keysight VXI mainframes provide rugged enclosures with innovative air distribution systems for extremely quiet and efficient cooling. With power supply capacities up to 1000 watts, you can easily configure the system that truly meets your needs.
-
product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
Working room dimension: 610×610×610mm• Temperature range: RT+10℃~+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
product
Calibrator, Calibrated w/D & U, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL DU
The 72-6694 CAL DU from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
product
Mini Redundant Power Supply; ATX 500W
PS500-HRP
*Input Range: 100~ 240VAC Full Range*Output Voltage:**+5V, 25A (1A min)**+3.3V, 25A (1A min)**+12V, 41A (1A min)**-12V, 0.8A**-5Vsb, 3.5A (0.1A min)*MTBF(hours): AT 25°C 100,000h*Safety: UL, TUV, CB, CCC, RFI/EMI Standards, FCC Class B, CISPR22 Class B*Dimensions: 185 x 150 x 86 mm*Compatible with Axiomtek products: AX61492
-
product
Arduino CAN Shield
IFB-10003-IWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
4kW Electronic Load
PT04-48
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
product
PXI 32 Channel I/O, High Side Driver
40-413-001
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
product
PMAC Accessories Modules
Power supplies, expansion modules and other accessories for the PMAC motion controllers.
-
product
SWB-2813, 4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-13
4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2813 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
External DC12V Power Gem Tester
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
12V power supplies (or 12VDC power supplies) are one of the most common power supplies in use today. In general, a 12VDC output is obtained from a 120VAC or 240VAC input using a combination of transformers, diodes and transistors.
-
product
ACDC
P Series
The P Series boast over a decade of reliable, field proven service and are the recognized industry standard for high performance AC/DC power supplies. The P Series is 2.0” pin spacing..
-
product
Hot Swap & ORing
Renesas' positive and negative hot swap controllers enable power supply designers to increase the long-term reliability of their systems. Our latest hot swap controllers include advanced features such as IntelliTrip™ (dual-response to degree of overcurrent condition), adjustable current regulation duration, load current monitoring and integrated charge pumps, making them ideal for hot swap applications.
-
product
High-Performance Autoranging DC Power Module, 50V, 10A, 100W
N6752A
The Keysight N6752A is a 100 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
product
Lab Power Supplies
SYSKON Series
The analog interface is equipped with two programmable trigger inputs and three signal outputs, which can be linked to various device functions for indication, or for controlling external devices and an auxiliary power output. Beyond this, monitor outputs and control inputs for voltage and current setpoints are available as well. Sensing leads allow for auto-sensing operation at the power consumer. Strict menu-driven operation supports highly diverse programming functions. The device is transformed into a freely programmable test signal generator by means of an expanded sequence memory and extra functions.
-
product
cPCI Serial 3U AC 300W
Hartmann’s cPCI Serial Power Supplies comply with PICMG and offer a wide range AC input with utilization of serial communication. These supplies are developed and produced with quality and durability in mind, at a price that won’t bankrupt your project. Talk to a Hartmann representative today about your power needs!
-
product
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W
T3PS160141P
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W.
-
product
Power Supplies
VP SERIES
Crafted for quality, performance and incredible value. This entry-level solution gives you everything you need in a power supply. No twinkly lights or glittery paint jobs - a 120 mm fan for effective and quiet cooling, dual +12V rails for amazingly stable power and heavy-duty protection circuitry for peace of mind, no matter how demanding your system. And it comes with all the assurance of Antec's AQ2 Antec Quality 2 year limited warranty. All the features, none of the waste: for builders that are strictly business, the VP550F is strictly power.
-
product
Full Wafer Test System
FOX-1P
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
product
Power Supply
High precision analog control loop power supplies for inductive loads such as electromagnets, superconducting coils, Helmholtz coils and others.Autonomous analog power supplies with digital controls, readouts and supervision. The interfaces are digital and analog
-
product
2450 MHz Industrial Microwave Generators
Alter® 2450 MHz Industrial Microwave Generators are built on MKS Alter® Product experience and designed with rugged and reliable switch mode power supplies for demanding industrial applications. They offer compact generators up to 3kW in a 19 inch standard rack with a remote head and integrated isolator.
-
product
4U 20-slot Extended Rackmount Chassis
AX61492
*Three 5.25" and two 3.5" HDD drive bays*Three 12 cm hot-swap ball-bearing fans*Supports 20-slot backplane*Hot-swap redundant or PS/2 power supply supported
-
product
Advanced Power System - Dynamic DC Power Supply, 40 V, 50 A, 2000 W
N7972A
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
Power Supply 600W
UEP10M66 / CEP10M66 -
The UEP10M66 series is a linear regulated plug-in power supply for use in CERN type NIM and CAMAC crates with 600W power output for applications with extreme +/-12V loads. This high precision and lowest noise power supply is designed as a very compact unit with extremely low volume to power relation.
-
product
Dual Channel High Voltage Linear Amplifier
F20AD
This unit contains two independent F20A amplifiers that share common ground reference and power supply.





























