Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - 6U VPX
Model 57670
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
160 Pin DIN 41612 Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
product
ADAQ Data Systems
Atec’s Data Acquisition and Control System (ADAQ™) is a modern, full-featured, highly integrated hardware and software solution that is applicable for use with most commercial and military turbine engine test cell applications. Built upon National Instruments’ respected LabVIEW platform, ADAQ™ is robust, versatile, user friendly, and specifically designed to handle the demanding requirements of engine testing. It links seamlessly to digital engine modules (FADECs, DEECs, EECs, ECUs) as well as legacy analog and mechanical controls. Users can create, remove, calibrate and display channels, as well as generate custom calculations, screens and reports. Beyond the most impressive manual throttle control and operation available, Atec’s ADAQ™ additionally offers the option of fully automated testing.
-
product
USB Module
USB-200
This USB module enables a fast connection of the sensors tothe computer (PC, Mac, XO, or Linux).This module is the first in a chain of sensors connected toa USB port of the PC. It provides both power from the PC to thesensors and communication between the PC and the sensors.
-
product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-222-E
The 40-781A-222-E (PXI) and 42-781A-222-E (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Coax/20-26 GHz/ 75 Ohm HD, Module, Receiver, iCon Series, 18 Position
510160114
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161114. (May mate with other ITA modules, as well.)
-
product
2 Amp PXI Large Matrix Modules - BRIC
Our 2 Amp PXI Large Matrix Modules use high-quality electromechanical relays to achieve their 2A switch rating. The BRIC structure allows the creation of large PXI matrices over multiple slots without the use of expensive external cables. The fully integrated programming interface represents the matrix as a single entity, easing user programming and reducing the likelihood of user errors.
-
product
Automatic Test Equipment (ATE) Module Products
Automatic Test Equipment (ATE) Module Products by ADSYS
-
product
Scienlab Measurement & Control Module
SL1060A
The Measurement & Control Module SL1060A is a mobile measurement module for measuring voltage input ±10 V with 16 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
product
Breakout Box and Data Logger
1U643-001
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
product
LXI Scalable Matrix - 8Amp 8x10 Matrix Plugin Module
65-239-202
The scalable matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of sub-cards. It is purchased as an empty chassis with a quantity of sub-cards required for a particular matrix size. As your requirements evolve, additional cards can be easily fitted. When new cards are added, the control software automatically detects the new configuration.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-314-HI
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
C Series Universal Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
PXI/PXIe RF Matrix, 16x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-012-L
The 40-724-012-L (PXI) and 42-724-012-L (PXIe) are 16x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
product
IRD
SFT356xL
Hangzhou Softel Optic Co., Ltd.
SFT356xL HD IRD is softel’s all-in-one device which integrates demodulation, de-scrambler, re-mux and decoding in one case to convert RF signals into audio/video (CVBS /YpbPr /HDMI) output. It is a 1-U case which supports 1 tuner inputs to receive signal from satellite, cable or terrestrial devices. The two CAMs/CIs accompanied and BISS modules can descramble the programs input from encrypted RF. Its pluggable structure design greatly facilitates the change of modules (demodulator or decoder) as needed.
-
product
Breadboard Module for 34980A
34959A
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
product
Assured Positioning, Navigation and Timing (A-PNT) Solutions
Curtiss-Wright Defense Solutions
Our assured positioning, navigation, and timing (A-PNT) solutions are designed to provide ground vehicles with access to trusted PNT information while operating in conditions with limited, impeded, or denied GPS/GNSS. Cost-effective, simple to configure, and size, weight, and power (SWaP)-optimized, our modules and systems are rapidly deployable on both combat and tactical wheeled vehicle platforms.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-120
The 40-297A-120 (PXI) and the 42-297A-120 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
product
PXI Quad SPDT RF Switch 6GHz 50 SMA Terminated
40-880-002
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
PXI Single 4 Channel Fibre Optic Mux SC/PC
40-850-214
The 40-850-214 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-314-M62.5
The 40/42-850A-314-M62.5 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 12.4GHz, 50Ω, N-Type
40-780B-512
The 40-780B-512 (PXI) and 42-780B-512 (PXIe) are dual SPDT 12.4GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
PXI High Density Multiplexer, 2-Bank, 32-Channel, 1-Pole
40-610A-011
The 40-610A-011 is a 2-bank, 32-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules
610131108
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-030
The 40-254-030 (PXI) and 42-254-030 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Optical Fiber Identifier
BD-IF400D
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.
-
product
PXI 4-Slot BRIC 48x8 Matrix, 2A 2-Pole (2 sub cards)
40-565A-002-48X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
