Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
PXIe-2531 PXI Matrix Switch Module, 256-Crosspoint, Reed Relay, .5 A, 60 V
780587-31
Matrix Switch Module
512-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXIe‑2531 is a high-density PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring compact reed relays with switching speeds up to 2,000 cycles/s, the PXIe‑2531 is designed for low‐current, high‐speed switching. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI 2 Slot BRIC 90x8 2-Pole (3 sub-cards)
40-561A-222-90X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Graphic Display Module
VIEW-101
-
The Graphic display module is used to run experimentswithout a PC. It displays the sensor's measurements indigital and graphical forms. It can also be used to program thesensor's experiment setup as well as viewing the input from up tofive sensors at a time.
-
Product
Analog Input Module
PMC341
-
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. All 16 channels share two generous 512-sample memory buffers. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
Product
Tribometer
-
NANOVEA Tribometer is a powerful and adaptable all-in-one friction and wear tester with the widest range of testing and environmental modules on the market. The simple design of a NANOVEA Tribometer allows for fast interchangeability to accommodate for any research need and requirement or standard.
-
Product
High Voltage Switching Systems
HXV Series
-
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
60 GHz Development System
PEM009
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules for quick prototyping for millimeter wave wireless system development. This high speed wireless 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development systems make it easy to design new products and applications in the emerging unlicensed millimeter wave ISM V band.
-
Product
PXI 2A Multiplexer, 1-Bank, 16-Channel 8-Pole
40-614-018
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP8T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
40-788-021-T
Multiplexer Module
The 40-788-021-T (PXI) and 42-788-021-T (PXIe) are single failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-331-HI
Programmable Resistor Module
The 40-230-331-HI (PXI) and 42-230-331-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 3.55kΩ
40-252-023
Programmable Resistor Module
The 40-252-023 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Phase Modulated Driver
-
The Phase Modulation Capable RF Driver / Stabilizer is an eight channel, two phase RF driver intended to drive devices such as the Harris H-401. The driver provides both amplitude and phase modulation capabilities in a single unit. The device can be operated in driver mode where the operator has full control over amplitude, frequency, and phase, or in stabilizer mode where the driver automatically adjusts the operating parameters based on optical feedback from an optical pick-off point.
-
Product
Modules - Modules, Diode
-
Diode modules from Vishay feature a range of technologies including FRED Pt®, HEXFRED®, and high performance Schottky, with reverse voltage ratings up to 2500 V and forward current ratings up to 600 A.
-
Product
PXI 100 x Normally Closed Relay 1A 60W
40-145-201-NC
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
SMARC Short Size Module with Intel® 6th Gen. Atom® x6000 Processors (formerly codename: Elkhart Lake)
LEC-EL
Computer on Module
The ADLINK LEC-EL is a SMARC module that supports Intel Atom® x6000 (x6425E, x6413E, x6211E, x6200FE, x6425RE) processors (formerly Elkhart Lake) with integrated Intel® UHD graphics and high speed interfaces. LEC-EL modules support up 8GB LPDDR4 memory, and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
cRIO-PN-S, Slave, C Series PROFINET Slave Interface Module
782131-01
Interface Module
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
Chassis
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with Virtex-6 FPGA - XMC
Model 71640
-
- View product video- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- Sync bus for multimodule synchronization- PCI Express Gen. 2 interface x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI High Voltage Amplifiers
-
Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.
-
Product
SQFlash SATA Slim 640, SATA Gen. 3 (6.0Gbps)
SQF-SLM 640
Solid-State Drive
MO-297 Half-Slim SATA Module, Compliant with SATA III and SATA v 3.2 standard. Supports LDPC & RAID ECC, Supports Fragment Writing Technology and Flush Manager. Shock resistance, anti-vibration and low power consumption, GUI management tool & software API package.
-
Product
DUT Matrix 32 DUT Matrix Channels
40-530-021
-
The 40-530-021 is a high density 32x8 1 pole reed relay matrix. Typical applications are signal routing in functional ATE and data acquisition systems. It consists of highly reliable sputtered ruthenium reed relays that offer >10e9 switching cycles to ensure maximum switching reliability with a long service life and stable contact resistance. Larger arrays can be built by daisy-chaining the common signals from multiple PXI modules
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 26.7k
40-297-132
Programmable Resistor Module
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Replacement Protective Cover, ICon, Receiver
310113460
Protective Cover
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the iCon Receiver. The receiver protective cover comes with a beaded chain and mounting hardware.
-
-
Product
18 GHz Differential TDR/TDT Probe Kit
N1021B
Accessory Kit
Connect PCBs and other devices without connectors to TDR/TDT modules in the oscilloscope mainframe
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
