Linear Amplifiers
Linear PA is one which has a linear relationship between the input and output.
-
product
Fiber Transmitter With Fiber Amplifier
FTFA 844
- Auto Switch over from Fiber to RF & Vice versa- Works as Transmitter & Fiber Amplifier- AGC / MGC - Automatic & Manual Gain Control- Very High MER / BER- High Quality DFB Lasers with Isolators- RF Input : 78dB ~ 90dB- Optical Input : -8dBm ~ +2dBm- Optical Wavelength : 1310nm- Power : 110VAC ~ 240VAC, 50HzSpecifications:- Bandwidth: 47 ~ 860 MHz- Input RF Level: 75 ~ 85dBuV- Input Optical Level:- -8dBm ~ +3dBm- SMPS Power Supply:- 110V AC ~ 265V AC- Power Consumption: 50Watt- AGC Range: 0 ~ -8dBm
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Ultra Low Level DC Voltage Amplifiers
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
product
Amplifiers
Instead of cascading a set of narrowband amps, use a single amplifier from Keysight and enjoy ultrabroad bandwidths - like 0.01 to 26.5 GHz, 0.045 to 50 GHz, and ranges in between. But the best thing about Keysight broadband amplifiers is what they eliminate and reduce: noise, crossover networks, and multiple power supplies.
-
product
Broadband Power Amplifier
PAS-00210-80
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case* Internal Cooling Fans* Type N Connectors* Over-voltage, over-current protections* Microprocessor controlled (optional)* Current monitor (optional)* Ethernet interface (optional)* Variable Gain (optional)* ALC power control (optional)
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
Ultra-broadband Power Amplifier Systems
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink provides ultra-broadband power amplifier systems in rack-mounted configuration with output power capacity from 50-Watt to 2000-Watt for applications including EMC testing, communications, and TWT replacement.
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
product
Current Sense Amplifiers
Analog Devices’ current sense amplifiers offer excellent performance for a wide array of automotive and power management applications. These devices accurately amplify small voltages in the presence of large common-mode voltage, and provide high bandwidth, as well as level shifting and bidirectional capability. Excellent dc and ac accuracy over a wide temperature range from –40°C to +125°C minimizes errors in your measurement loop while not sacrificing on cost and package size.
-
product
Microwave Power Amplifier 1/4 Watt, 2 GHz to 50 GHz
GT-1050B
The Spanawave/Giga-tronics GT-1050B Microwave Power Amplifier offers linear high-power amplification across multioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
product
Power Amplifier
2734
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
product
CATV Amplifiers
Qorvo's amplifiers for cable TV (CATV) include single-ended, dual and differential amplifiers for a wide range of 75-ohm applications. These devices offer the versatility and economy needed to support triple-play requirements, system upgrades and greenfield deployments.
-
product
High-Speed System Sync and Distribution Amplifier - SOSA Aligned 3U VPX
Model 5503
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- Synchronizes up to 32 channels across four Quartz boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions- Optional VITA 67.3D optical interface for backplane gigabit serial communication
-
product
Bench DC Power Supply, Linear Regulation - Single, Dual Or Triple Outputs, Analogue Control, 30 To 130 Watts, Silent Cooling
EL-R Series
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
product
Switched Limiting Amplifier With Detected Output
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
product
Amplifier Module
LNAM-FBX
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
product
CATV Booster Optical Amplifier
HA5100
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
product
2 Ch Linear Vibration Motor Tester
BK2120C
the BK2120C runs up to 4 vibration sweeps, which you define, to check whether your linear vibration motor is within the limits you set. And now you can set up your own feedback so it's even easier to determine the class of pass or the reason for failure. You still get fast, high quality testing for your linear vibration motors on the product line. And it's still versitile enough to be used for QA or QC as well.
-
product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
OEM Femtosecond/Picosecond Laser and Amplifier Modules
They provide output wavelength options at 780 nm, 925 nm, 1030 nm, 1064 nm and 1550 nm and can be used as stand-alone systems with a user-provided 5 V DC power supply or integrated into higher power laser platforms. The high quality ultrafast pulse streams are perfect seed sources for chirped pulse amplifier systems used in diverse applications, such as high precision microelectronics micromachining, laser eye surgery and nonlinear spectroscopy.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
GHZ-Wideband Amplifiers
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
product
Linear Testfixture Cassette and VPD ITA Frame Not Included, UUT 306 x 248 mm
MG-02 VPC G12
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable CEM Backpanel for VPC G12(x) ITA frame mount• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
-
product
Reference plus Comparator or Amplifier
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
product
Broad Band Amplifiers
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
product
SX Range Broadband Power Amplifiers 0.8 GHZ - 6 GHZ
SX Series
Class A solid stateBroadband (instantaneous dual band): 0.8 GHz 6 GHzTypical output power :40 W CW (0.8 3.2 GHz) and15 W CW (3.2 6 GHz)Linear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 25 W and H < -20 dBc up to 3.2 GHz andP1dB > 10 W and H < -20 dBc from 3.2 GHz to 6 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to to SX 40/30 or SX 70/15 or SX 70/30 possible (7U)Reliable, efficient and robust19" Rack3 years standard warranty
-
product
Linear Power Supplies Programmable, Local or Digital Control, Ultra Low Ripple/Noise
Series MBT-G
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
