Linear Amplifiers
Linear PA is one which has a linear relationship between the input and output.
-
product
LVDT Sensor Amplifiers
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
product
Light Sources and Amplifiers
Light sources simulate the optical voice, video and data signals of real-life service applications, which is why they are used in various types of tests. Discover a broad range of products that cater to various testing requirements: singlemode or multimode, polarized or non-polarized, broadband or narrowband, tunable, ITU-wavelength-centered and much more.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Portable Power Amplifier
PAV250Bip
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
-
-
product
Thermocouple Interface Amplifiers
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
product
Amplifier Built-In/U-Shaped Micro Photoelectric Sensor [Compact/Connector Built-In Type]
PM-65
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-65 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1 mm thereby reducing the possibility of sensing objects colliding.
-
product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
product
Pulsed Injection Locked IMPATT Amplifiers
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
Ultra-low Noise High Voltage Amplifier
WMA-200
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
product
Transimpedance Amplifiers
Artifex Engineering GmbH & Co. KG
Applications include photodetection with PMTs and photodiodes, spectroscopy, Scanning Tunneling Microscopy, ionization detectors, pyro and piezoelectric detectors.
-
product
RGB 1×3 Video Distribution Amplifier
VDA403
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
DSP And Power Amplifier
DMPA12
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
Compact Linear Line Array Loudspeaker
LEOPARD
Say hello to LEOPARD, the most lightweight, versatile line array in its class. The best-selling loudspeaker in the LEO Family faithfully reproduces sound with unsurpassed depth and clarity in a broad scope of installed and touring applications. In Meyer Sound tradition, LEOPARD delivers exceptional phase coherence, consistent coverage, extremely low distortion, and unrivaled power-to-size performance.
-
-
product
Synchro/Resolver to Linear DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
product
Low Noise Amplifiers
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
product
RF Power Amplifiers
Specially selected products to complement our ultrasound measurement equipment.
-
product
Programmable Linear DC Power Supply
DP800 Series
DP800 series includes single output, two output and three output programmable linear DC power supply. They have pure output, excellent performance indicators, multiple analysis functions, rich interfaces, and can meet the diverse testing needs.
-
product
Automatic Level Control Amplifier
RF Lambda’s automatic level control amplifiers allow customers to implement an AGC function into their system to tune the gain and stay linear with high input signals without the need to manually control the input level. Hermetically sealed options are available upon request.
-
product
Waveform Amplifier 30 Volts Pk-pk
WA301
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
-
product
Linear Power Supplies Programmable, Digital Control, Rack Mount, Ultra Low Ripple/Noise
Series MAT
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
product
Linear AC Power Supply
Applicable places : equipment testing, compressor testing, monitor testing, motor equipment testing, air conditioning equipment testing, optimal power supply for R&D units, testing of various electrical products, 400Hz power supply for military equipment, special power supply for switching DC power supply testing, transformer /TRIAC / SCR...
-
product
Erbium Doped Amplifier
AEDFA-FTTH
Amonics FTTH EDFAs inherit the reliable design of Amonics's optical amplifier technology. They exhibit high output power, high gain with very low noise, and are ideal for FTTH network amplification. Integrated CWDM splitters are available to enable routing of 1310nm and 1490nm data streams from OLT to ONU through EDFAs. The turnkey rackmount EDFAs provide microprocessor controlled alarms and status indicators. An integrated Ethernet TCP-IP computer interface enables easy control, diagnostic functions and data acquisition.
-
product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
product
Amplifier Module
LNAM-FBX
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
