PCB Piezotronics, Inc.

Product

Conformal Ballistic Pressure Sensor

Model: 117B67

-

PCB Piezotronics, Inc.

Model: 117B67 - PCB Piezotronics, Inc.

Conformal ballistics pressure sensor, 22 WMRF, 22 WRF, 22 WRF WITH 0.50" Centerline, 17 RF Mag, 17 HMRConformal ballistics pressure sensor for 17 HMR, 17 Magnum RF, 17 RF Magnum, 22 WMRF, 22 WRF, and 22 WRF with 0.50" centerline caliber cartridges.

Product

Precision Condenser Microphone

377C10

-

PCB Piezotronics, Inc.

377C10 - PCB Piezotronics, Inc.

Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%

Product

ICP Microphone System

378C01

-

PCB Piezotronics, Inc.

378C01 - PCB Piezotronics, Inc.

This model includes a 1/4" microphone cartridge, a mated preamplifier with TEDS, and system calibration. Click the following for individual component information.

Product

Miniature Electrodynamic Shakers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Miniature electrodynamic shakers are small, portable units designed to simplify your vibration testing needs. From the SmartShaker™ with an integrated amplifier, to an Inertial Shaker System for testing in hard-to-reach areas, mini shakers offer flexibility when testing. Miniature shaker systems range from 2 lbf (9 N) to 7 lbf (31 N) sine peak force excitation.

Product

ICP Electret Array Microphone

130A23

-

PCB Piezotronics, Inc.

130A23 - PCB Piezotronics, Inc.

Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC

Product

Endevco Miniature Piezoresistive Silicon Pressure Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Accurate and Reliable Performance at Extreme Pressures.

Product

General Purpose Piezoelectric Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Piezoelectric accelerometers offer tremendous versatility for shock and vibration measurements. These rugged sensors can withstand adverse environmental conditions. A wide variety of configurations are available to support multiple application requirements. Specialty units are also available through mechanical or electrical design modifications or additional qualification testing.

Product

General Purpose Pressure Sensors For High Frequency

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® Series 113B dynamic pressure sensors set the standard for extremely fast, micro-second response with a wide amplitude and frequency range. These characteristics allow them to excel in high-frequency applications, where minimum sensor diameter is required.

Product

Ground Isolated ICP® Pressure Sensors For High Frequency

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® Series 102B is a ground isolated version of the Series 113B. These sensors have all of the same features and benefits of the 113B Series, plus the added benefit of isolation, which helps prevent ground loop problems. This series can accommodate an optional ablative coating (Prefix: CA) to protect the diaphragm from thermal shock in flash-temperature applications.

Product

Externally Polarized Precision Condenser Microphones & Preamplifiers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Externally polarized microphones set the initial standard for all acoustic test and measurement applications. They rely on a dedicated 200V power supply and specialized cables with 7-pin LEMO® connectors. Their straightforward design supports a wide product range. Often chosen as replacements for existing models or when prepolarized alternatives are unavailable.

Product

MEMS DC Response Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.

Product

High Temperature Charge Mode Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).

Product

Pressure Sensors For Blast Testing

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.

Product

Microphone Preamplifier

HT426E01

-

PCB Piezotronics, Inc.

HT426E01 - PCB Piezotronics, Inc.

Nominal Microphone Diameter1/2Frequency Response Electrical Noise(at 22 C) (Flat 20 Hz to 20 kHz)Distortion (3 V rms input at 1 kHz)<-70 dB<-70 dB[1] EnvironmentalTemperature Range (Operating)-40 to +248 FExcitation Voltage 20 to 32 Constant Current Excitation 2 to 10 mA

Product

Fatigue Rated Low Profile Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.