PCB Piezotronics, Inc.

Product

Precision Condenser Microphone

377C01

-

PCB Piezotronics, Inc.

377C01 - PCB Piezotronics, Inc.

Performance:Nominal Microphone Diameter:1/4"Open Circuit Sensitivity 2.0 Open Circuit Sensitivity (3 dB)-54 dB re 1 V/PaFrequency Range Inherent Noise<35 Temperature Coefficient of Sensitivity (+14 to +122FHousing Material: Stainless Alloy

Product

ICP Microphone System

HT378B02

-

PCB Piezotronics, Inc.

HT378B02 - PCB Piezotronics, Inc.

This model includes a 1/2" microphone cartridge, a mated preamplifier with TEDS, and system calibration. Click the following for individual component information.

Product

Fatigue Rated Low Profile Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.

Product

Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

A device that measures the vibration, or acceleration of motion, of a structure.

Product

ICP Electret Surface Microphone

130B40

-

PCB Piezotronics, Inc.

130B40 - PCB Piezotronics, Inc.

Low-profile surface pressure microphone and preamp, prepolarized

Product

Sensor Cables

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® manufactures a wide variety of cable assemblies that will mate to different sensor types, signal conditioners and data acquisition systems. Cables are an important part of every measurement system. PCB carefully selects different raw cable types from trusted suppliers and time is taken to design cable to connector interfaces that will be reliable. All cable assemblies are produced at one of PCB's manufacturing locations to tightly controlled assembly procedures that ensure durability in various applications and environments.

Product

General Purpose Coaxial Cables For Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

General purpose coaxial cables are used with single axis ICP® sensors. This table provides relevant specifications for four cable types. Type 002 is the most commonly used, but three other types are also available.

Product

Quartz ICP® Force Rings

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load. The through-hole mounting supports platform, integrated link, and support style installations using either a through-bolt or the supplied stud.

Product

Precision Condenser Microphone

377B02

-

PCB Piezotronics, Inc.

377B02 - PCB Piezotronics, Inc.

1/2" free-field, prepolarized condenser microphone, typical sensitivity= 50 mV/Pa (+/-1.5 dB), 3.15 Hz to 20 kHz (+/-2 dB).

Product

ICP Microphone System

378C10

-

PCB Piezotronics, Inc.

378C10 - PCB Piezotronics, Inc.

This model includes a 1/4" microphone cartridge, a mated preamplifier with TEDS, and system calibration.

Product

Canister Load Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.

Product

Microphone Preamplifier

426B31

-

PCB Piezotronics, Inc.

426B31 - PCB Piezotronics, Inc.

Performance:Nominal Microphone Diameter:1/4" Frequency Response:3.98 to 126000 Hz3.98 to 126000 10.0 to 126000 Hz10.0 to 126000 HzElectrical Noise (A-weight)3.8 TEDS CompliantYes

Product

In-line ICP® Charge Converters

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.

Product

ICP Blast Pressure Pencil Probe

Model: 137B21B

-

PCB Piezotronics, Inc.

Model: 137B21B - PCB Piezotronics, Inc.

Quartz, free-field, ICP blast pressure pencil probe, 1000 psi, 1 mV/psi, BNC connector

Product

ICP® Shock Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.