Filter Results By:
Products
Applications
Manufacturers
kV
A thousand volts of electromotive force.
-
product
Self-Rectified Generator Power Supply Mains 90 to 300 kV
SITEX D3006
Self-Rectified Generator Power Supply Mains
-
product
Self-Rectified Generator Power Supply Crawler Battery 9 to 300 kV
SITEX C3003
Self-Rectified Generator Power Supply Crawler Battery
-
product
RS-422 RS-423 RS-485
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
product
ELECTRONIC MEGOHMMETER
MI-2550e
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
1kV, 120 MHz High Voltage Differential Probe Without Tip Accessories and with Auto Zero Disconnect
HVD3106A-NOACC
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
VLF Testing and Diagnostics Unit
Frida
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR frida. The portable and powerful high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 20 kV and electrical equipment. Another function is insulation testing on electrical equipment.* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
product
Multifunctional testers
MI 3152H EurotestXC 2,5 kV
MI 3152H EurotestXC 2,5 kV is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN and TT earthing systems expanded with insulation resistance measurement with the test voltage up to 2,5 kV are managed by a completely new user interface based on large colour touch screen display.
-
product
Differenzial Probe
BumbleBee®
PMK Mess- und Kommunikationstechnik GmbH
BumbleBee® is a 400 MHz, 1 kV CAT III high-voltage, differential probe, that can be used with anyoscilloscope or device providing 50 Ω termination.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
Matrix Card
MATX4010
The MATX4010 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 10 Amps and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software.
-
product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-913-HI
The 65-231-913-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
LXI High Voltage Switching - 1-Bank, 1-Pole, 24:1 Multiplexer Plugin Module
65-231-902
The 65-231-902 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Beam Directional Power Supply Battery 40 to 120 kV
CP120B
This ultra-light, compact and battery operated constant potential portable X-Ray generator is the perfect tool for specific NDT applications that require repetitive short exposures. Its versatility also makes it the ideal piece of equipment for security applications. In fact, in combination with the FLATSCAN15, the FLATSCAN30 and other digital X-Ray detectors, the CP120B will – thanks to its small focal spot and constant potential X-Ray output – enhance image quality and definitely contribute to a reduced exposure time.
-
product
HIGH VOLTAGE MEGOHMMETER
MI-10KVe
The MI-10KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 10 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 2.000.000 MΩ with four test voltages: 1 kV - 2 kV - 5 kV and 10 kV.
-
product
Digital Insulation Tester
1550C
The Fluke 1550C performs digital insulation testing up to 5 kV, and makes data collection easy through the Fluke Connect™ wireless app. Remote operation lets you spend as little time as possible in potentially hazardous zones.
-
product
Wet-Mateable Multi-Channel Electrical Connectors Rated for 1/1.7 (3.3) kV and 30 A
Nautilus WM1.7-30
Teledyne ODI's patented Nautilus is recognized as the leading choice for high reliability wet-mateable, multi-channel electrical connectors. Over 100,000 Nautilus connectors have been delivered for projects in diverse industries including oil and gas, oceanography, and defense.
-
product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
product
Transformer Turns Ratio Testers
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
product
Universal Multichannel System up to 1.5 kV
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 1.5 kV (A1538D) and 0 ÷ 1/1.3/1.4 kV output voltage (A1515B)- Maximum Current 10 mA, 0.1 or 1/0.1, 3/0.3 mA (dual range boards)- Radiall Multipin, SHV or DB37 connectors- Available with either positive or negative polarity (A1538D and A7038)- Up to 2 nA / 100 pA current set / monitor resolution- Up to 20 mV / 2 mV voltage set / monitor resolution- Very low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A1515B only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for GEM and Vertex detector and dedicatedaccessories (A1515B boards only)
-
product
HIGH VOLTAGE MEGOHMMETER
MI-15KVe
The MI-15KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3.000.000 MΩ with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV.
-
product
10 KV Oil Cell
• Operating range 2 to 12kV for a stress of 200 to 1100V/mm • Cell capacitance -65pF nominal • The cell is suitable for use with Eltel models CST- 12KSA, ACTS-5k & ACTS- 12k test sets • Measurement at 10kV at ambient temperature only
-
product
Insulation Resistance Measurement
MD 10KVR
The digital insulation tester model MD-10KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 10 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
product
AC Hipots for Apparatus Testing
PFT Series
PFT Series test sets are portable, ideal for testing substation apparatus. These are among the smallest, lightest, and most economical AC hipots available. Standard models are available from 10 kV AC – 100 kV AC and rated 1 kVA – 3 kVA.
-
product
Pil Dielectric Test Sets
DTS Series
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
product
Cable Assembly, Receiver, 36", Mini Power, 4 Banana Plugs, 1 KV for PXIe-4081
540067030208
Cable Assembly, Receiver, 36", Mini Power, 4 Banana Plugs, 1 KV for PXIe-4081
-
product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-913
The 65-231-913 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Beam Directional Power Supply Battery 40 to 160 kV
CP160B
Next to the CP120B, the CP160B is the slightly more powerful version of our ultra-light, compact and battery operated constant potential portable X-Ray generators. Allowing penetration reaching up to 30 mm for steel, the CP160B is the perfect tool for specific NDT applications that require repetitive short exposures, as well as security applications.
-
product
Beam Panoramic Power Supply Battery Crawler 40 to 160 kV
CP160CR
Designed to fit into 6” pipelines and higher, the CP160CR constant potential X-Ray generator for crawlers is – in its category – the most powerful panoramic X-Ray tube head in the world for crawlers. The generator is making the cutting edge constant potential technology of the CPSERIES even more compact into a 9.9 kg – 120 mm diameter X-Ray tube head. The crawler unit is capable of penetrating up to 28 mm of steel in 10 minutes, which corresponds to just a 25 second exposure time for 6” standard pipeline welds.
