Filter Results By:
Products
Applications
Manufacturers
Torque
turning force.
See Also: Torque Sensors, Torque Testers, Torque Transducers, Torque Meters, Dynamometers
-
product
Torque Tester
TorqueLab® LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
product
Flex Power In-Line Auto Shut-Off Pulse Tools
Auto shut-off in-line pulse tool that automatically shuts off the air supply when the pre-set torque is reached. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Offers comfortable rubberized non-slip grips for easy handling and excellent thermal ergonomics. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
product
Prop Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
product
manual torsion bench
TWIST
To carry out a precise, repetitive torque measurement, it is often necessary to use a torsion test stand. The Twist, 10 to 500 lb/in torsion test stand, with combined torque/angle measurement provides this function. The torsion meter enables torsion tests to be made on various samples such as springs, metal or plastic parts.
-
product
Torque Systems
The Drive Plate Torque System uses a low power radio link to transfer digitised strain measurements from a rotating wheel hub to a stationary antenna mounted nearby. The signals are passed to a receiver where they are decoded and output as CAN bus messages and analogue outputs.
-
product
Torque Testers
Torque testers are ideal for a variety of applications in light assembly and can be used to test hand tools, power tools and even pulse tools.
-
product
Torque Metering System
Model TMS2200
Full capability of standard RDT2100 model with the addition of a Class I Division II certification of the system.
-
product
Torque Instrument
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
product
EZ-TorQ III Torque Analyzer
The EZ-TorQ III makes torque control easier and more available across every aspect of the line from the calibration lab to the assembly station. Highly portable and user friendly, this battery powered torque validation hub can be easily carried around the assembly line to spot check tools as part of a QA program or used at assembly stations for quick and easy torque tool validation and calibration. The new smart phone like touch-screen interface breaks down barriers and ensures quick and easy validation of different ranges as needed.
-
product
Bottle Cap Torque Meter
HN-B
Shenzhen Chuangxin Instruments Co., Ltd.
HN-B Series Cap Torque Meter is an intelligent metrologic instrument and is designed for detecting and calibrating the torsion of various caps. Installation of clamps is easy, rapid and its max diameter can reach 200mm.You can connect it to PC by USD output and transmit data for analysis and printing.
-
product
Non Contact Flange Torque Transducer
FF425
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
product
Economy Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052D
The Keysight 85052D economy mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection. Connector gauges may be ordered separately.
-
product
AC Engine Dynamometer
DA16
Power: 16 hp (11.9 kW)Torque: 42 lb-ft (56.9 Nm)Maximum Speed: 6,400 rpmConstant Torque Range: 0 - 2,000 rpmConstant Power Range: 2,000 - 3,200 rpmDecreasing Power Range: 3,200 - 6,400 rpmRotation: bi-directional
-
product
Calibration Equipment
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
product
Torque Tester
WDISR-IPS series
Built-in battery type DIS-IPS series successor. Ideal for managing automated and semi-automatic tools. For management of various torque tools A small detection part fits measurement of various points. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.
-
-
product
High Precision Canister Load Cell
Model 2000 Series
The Model 2000 Series High Precision Canister Load Cell was designed to accurately and precisely measure force, which many other quantities such as torque, thrust, and pressure are based, for aerospace applications. The Model 2000 Series, available with load measurement capacities up to 750K lbf, offers high performance and linearity and very low hysteresis. ±0.02% FS Hysteresis
-
product
Torsion And Shear Strain Gauges
Shear/Torque Strain Gages are for measuring shear strain and torque, typical applications are for measurements on torsion bars and determining shear stresses in shear beam load cells.
-
product
Engine Dynamometer
DH23
Power: 805 hp (615 kW)Torque: 1,275 lb-ft (1,729 Nm)Speed: 4,500 rpmWater Use*: 60 gpm (227.1 lpm)Inertia Value: 11.4 lb·ft2 (0.48 kg·m2)Shipping Weight: 475 lb (215 kg)*No Cooling System
-
product
Power Amplifier
5241
The Model 5241 is a voltage-controlled power amplifier designed exclusively for Magtrol's Model HD-825 Hysteresis Dynamometer. Because of its double braking system, the HD-825 requires more than 4 amps of power in order to reach full torque. The 5241 (which can provide up to 5 amps of output current) is necessary in order to amplify the power between a 6200 or DSP6001 Controller (which both have a maximum current output of 1 amp) and the HD-825 Dynamometer.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
Dynamometer
E-Series
AW E Series Dynamometers excel at producing high torque loads at low RPM making this series an excellent choice for testing DC motors and others. The E Series is also capable of testing high RPM motors up to 3600 RPM making this dynamometer a truly universal dynamometer.
-
product
Polyurethane Jacket RF Cable Assemblies
For applications where space is limited and minimizing transferred mechanical stress on the interface connection is a must...The polyurethane jacketed versions of our already proven cable assemblies deliver new engineering options to standard FEP jacketed cables.Polyurethane offers greater memory retention than a similar size cable jacketed with FEP. This feature offers the benefit of minimizing stress and torque applied to interface connections, such as those on a circuit board.It also allows cable to better maintain position in an installation where the "spring back" of an FEP jacketed cable could be problematic.Additionally, a polyurethane jacket offers improved abrasion resistance over an FEP jacket.
-
product
Torque Multipliers
Mountz torque multipliers make tough nuts easy to crack. They boost productivity, giving your workers the power to quickly turn the large fasteners found in the aerospace, transportation, mining, marine, oil/gas, and power generation industries. Mountz torque multipliers can improve process control compared to less controlled options, like impact drivers, and they guarantee quality of work. They generate less reaction torque than impact drivers as well, protecting your workers and their projects from harmful hammering. Electric and pneumatic torque multipliers are also much faster than hydraulic ratchets, helping you get more work done in less time. To top it off, they’re quiet, reducing the din of the workplace and helping to prevent hearing-related injuries.
-
product
Preset Break-Over Wrenches
MMTB
The MMTB is miniature preset production torque wrench with a fixed head. The versatile wrench is available with different head configuration options, like open, box, flare, hex key and ratchet head. MMTB models are design to have one permanent head style attached to it. When the MMTB torque wrench achieves torque, the head breaks-over preventing the operator from overtorquing the fastener. To Order Call (408) 292-2214
-
product
Preset Torque Screwdrivers
FG
Engineered and assembled in the Silicon Valley, the Mountz FG line of preset precision torque screwdrivers are the most advanced hand tools in the world.
-
product
Calibration Hangers And Weights
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
product
Torque Calibration
Our years of experience has show us that torque tools given the fact that they are mostly driven by large (and small) springs do tend to drift out of specification quicker than other measurement tools – we have the expertise in house to adjust your tools back into spec and of course provide before and after results.
-
product
Electric Servo Motor Type Power Circulation Type Rotary Torquer Tester
Tests For Clutches Durability, Torque Converters, Transmissions, Differential Gears, CVJs, Etc. Can Be Performed At Low Cost By The Load Using The Power Circulation System.
-
product
2WD Dynamometers
MD-500-SE XL
The 500 series dynamometer has a larger big brother – the MD-500-SE XL! The 500-SE is an excellent 2WD performance dynamometer and the XL model expands on these traits by adding in a much wider 98-inch outer track and a HUGE mechanical flywheel to increase the mechanical inertia of the dyno to about 2,000-lbs. This additional inertia helps reduce the duty cycle burden on the eddy current PAU and even allows for pulls to be done in a pinch in inertia-only mode. The XL handles vehicles like diesels and Ford Raptors where the 500 is a bit too narrow for these types of applications. The MD-500 XL’s multiple upgrade paths allows for an AWD upgrade in the future and enables it to accept a second eddy current PAU for increased loading capability. We’ve seen this dyno handle almost 2,000-hp to the wheels on power sweeps so don’t be fooled by the 1,500-hp peak measurement specification. If your tires will hook you can measure as much power as you are laying to the rollers. The large K250 eddy current PAU has plenty of torque for testing and tuning anything from your local diesel pickup crowd and local LS guys to classic carb stuff and front wheel drive cars. The 500-XL is great product at a great price with tons of range. It is also easy to install – buy the aboveground kit with the 16-ft ramps and have this dyno set up and ready to roll in your shop in a half a day! if you want to know more call us! We are always happy to answer questions.
