Filter Results By:
Products
Applications
Manufacturers
TEM Cells
Transversal Electromagnetic Mode cells.
See Also: Chambers, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, RF Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers, GTEM Cells
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
Striplines / TEM-Cells
Open, unsymmetrical 50 Ω stripline for automotive immunity testing of components.
-
product
EMC Testing Services
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
product
Field meters
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
product
EMF Exposure Test
sXcTEM835
Tests radiofrequency electromagnetic field exposures from mobile communication devices operating in the 900 MHz region (additional frequencies upon request). The setup is based on two Crawford TEM cells that are blindly excited by a fully computer-controlled signal unit.
-
product
MP field sources calibration set
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
product
TEM Antenna
TEM antenna is a broadband antenna with a flat response which makes TEM suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes TEM the optimal sensor for direct installation on medium voltage Switchgears and motors. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces.
-
product
Understanding TEM, TE, and TM Waveguide Modes
Energy can propagate through a medium or through what is currently believed to be a vacuum. Propagation modes vary depending upon the type of energy and the nature of the medium.Electromagnetic energy is transmitted in waves. Like sound, it may propagate equally in all directions, the wave energy radiating in concentric shells corresponding to amplitude. Or it may be directional, focused to form a tight beam.View more Understanding TEM, TE, and TM Waveguide Modes
-
product
Voltammetry Cell
SVC-2
SVC-2 Voltammetry cell can be used for 4 modes voltammetry cell setup. Each voltammetry cell has its specific feature. However, SVC-2 can be sed in 4 modes. Also can apply as an oxygen-free voltammetry cell.
-
product
Load Cell
Precise and robust and it has been designed to meet the requirements of a wide range of industrial weighing applications: hoppers, tanks, platforms. Is able to work in severe environmental conditions typical of applications in food, chemical and pharmaceutical industries.
-
product
Load Cells
Honeywell Industrial Automation
Honeywell Sensotec manufactures a wide range of tension, compression, and universal measurement load cells. These load cells are manufactured as standard, modified standard, and custom sensors to provide fast delivery. Many units can ship from our extensive stocking program within 24 hours.
-
product
Fuel Cells
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
product
Load Cells
Force Logic UK provides high-quality load cells, load indicators, and force measurement systems for a variety of industries. All our load cells are manufactured in the UK, and have passed through rigorous quality control standards for precise and accurate measurement, load monitoring systems, and industrial weighing applications. They are suitable for the measurement of static loads and dynamic forces in tension or compression, our load cells cover a wide range of mechanical forces, from 1kg to 1000 tonnes.
-
product
Load Cells
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
product
Load Cells
We make it our business to stay on top of emerging industry demands so that the load cells we provide help you meet your ever-changing test requirements. Our broad selection of competitively priced load products will help you meet the most demanding test and measurement requirements. Used in automotive, aerospace and defense, R&D, and process control applications, our drop-in replacement load cells are designed to provide years of dependable performance.
-
product
Solar Cell Simulation
Setfos
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
product
Scanning Droplet Cell
VS-SDC
Scanning Droplet System (SDC) uses a compact peristaltic pump to force electrolyte through a small diameter tube and into a specifically designed head. This PTFE-based SDC head is machined to allow electrolyte to flow past an installed Reference Electrode and then to a port at the base of the head.
-
product
HOT CELLS
Precisely engineered and constructed for continuous dependable protection and reliable everyday laboratory use. These cells come standard with shielding for the ionization chamber and utility connections.
-
product
S-Type Load Cells
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
product
Cell Testing
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
product
Load Cell Amplifier
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
product
Load Cell Electronics
All our electronics are continuously evolving to feature faster and more powerful components. This commitment to innovation ensures that we can meet any new challenge or application.
-
product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
product
Flow Cell Kit
QCMT
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
product
Load Cells
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
product
Beam and Singlepoint Load Cells
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
-
product
Load Cell Simulators / Testers
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
product
OEM Weigh Cells
Our weigh cells feature electromagnetic force compensation, strain-gauge type load cells, and electronic modules for various scenarios.
-
product
Load Cell Displays
We carry a wide range of digital displays for strain gage load cells. There are many options available to our load cell displays such as analog outputs to interface with a PLC, digital outputs for computer interfaces, I/O and relay outputs to control batching and checkweighing scales, and wireless load cell indicators.
-
product
Load Cell Indicator
9840
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
