Filter Results By:
Products
Applications
Manufacturers
Microphones
convert sound pressure to an electrical current.
See Also: Phone, Telephone, Geophones, Headphone, Hydrophones, Measurement Microphones, Mic, Electroacoustic, Headset
-
product
DSP And Power Amplifier
DMPA12
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
product
Power modules
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
product
Precision Condenser Microphone
377C01
Performance:Nominal Microphone Diameter:1/4"Open Circuit Sensitivity 2.0 Open Circuit Sensitivity (3 dB)-54 dB re 1 V/PaFrequency Range Inherent Noise<35 Temperature Coefficient of Sensitivity (+14 to +122FHousing Material: Stainless Alloy
-
product
The AudioTools Platform
AudioTools is the heart of the most comprehensive audio and acoustics test & measurement platform available today. With AudioTools, you can perform quick ad hoc measurements using only the iPhone in your pocket, or you can plug a Type 1 microphone into iAudioInterface2 for a full-featured professional test & measurement platform that meets ANSI and ISO specifications.
-
product
Class 1 Integrating Sound Level Meter System
NK021
This NK021 system includes a class 1 integrating sound level meter, class 1 acoustic calibrator, protective microphone windshield and is supplied in a hard wearing kit case.
-
product
Mini Bug Detector II
P7050
Peace of mind is now within your reach. The Mini Bug Detector™ offers state of the art protection against wireless microphones and transmitters. Perfect for securing homes, offices and hotel rooms, the unit not only detects such devices, its LED display and audio tone actually pinpoint the precise location of bugs. The audio alarm can be turned off for discreet sweeps, while the unit’s sensitivity adjustment minimizes false alarms. The Mini Bug Detector™ features wide range circuitry that enables it to detect concealed transmitters operating on frequencies from 50 MHz to 3 GHz, exposing most high frequency transmitters as well as more common VHF and UHF bugs. You didn’t know they were listening…until now.
-
product
PCI-4461, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 2-Input/2-Output Sound and Vibration Device
779307-01
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
Acoustic Noise Generator
ANG-2200
The ANG-2200 Acoustic Noise Generator creates a perimeter of noise that defeats acoustic leakage eavesdropping devices including wired microphones inside walls, contact microphones, audio transmitters located in AC outlets, and laser/microwave reflections from windows.
-
product
Special microphones
G.R.A.S. Sound & Vibration A/S
Special microphones are often required for applications where there are particular requirements regarding the methods of measurements and configurations
-
product
UHF/RFID/TETRA Power Divider Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless 350-1000 MHz RF power divider combiners are optimized for UHF, RFID, and TETRA power splitting and combining applications. Wireless microphone systems also typically operate in UHF frequencies, making an INSTOCK device ideal for splitting or combining antennas in UHF wireless microphone systems. Available in 2-way thru 48-way configurations with Type N, SMA, TNC and BNC connector configurations INSTOCK.
-
product
Precision Condenser Microphone
377C41
1/2" condenser microphone, free-field, 200 V Polarization
-
product
USB-4431, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 4-Input/1-Output Sound and Vibration Device
780164-01
The USB-4431 is designed for sound and vibration measurements. Input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones. The four USB-4431 input channels simultaneously digitize input signals. The analog output (AO) channel is ideal for stimulus-response tests and can be synchronized to the AI channels.
-
product
Test Sockets
MEMS Device
Patented MEMS Sockets from Ardent Concepts use a unique scrubbing action contact set which is ideal for today’s sensitive MEMS devices, including accelerometers, gyroscopes, MEMS microphones and other specialized devices used in mobile electronics applications
-
product
Directional Mic.
Our directional microphone helps you to find sources of noise easily and intuitively without any special knowledge.
-
product
ICP Electret Array Microphone
130A23
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
product
RJ-50 Test Connector
Test solution for RJ-50 connectors (10 pole). Applications in data networks, data transmission, power supplies, microphones, etc.
-
product
Precision Sound Level Calibrator
CAL200
The Larson Davis CAL200 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
product
Sound Level Meter
831-LOWN
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
product
MIPI SLIMbus
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
product
Ultrasound Microphone
M500
The M500 microphone is easily used with a Windows PC/tablet/laptop to record bat calls and other ultrasonic signals with the highest quality. For recording with the M500, the BatSound Touch or BatSound Touch Lite software is used.
-
product
USB MPEG Frame Grabber
2250
MPEG1/2/4 and JPEG capture to USB from an analog video source at D1 resolution 30 fps NTSC, 25 fps PAL Synchronous audio capture from line (stereo) or microphone (mono) inputs Motion Detection Text overlay (OSD) Powered through USB SDK works with multiple units
-
product
ICP Electret Surface Microphone
130B40
Low-profile surface pressure microphone and preamp, prepolarized
-
product
Surge Voltage Generator
SSG 2100
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
product
Directional Microphone
MI-8100
MI-8100 is a shotgun type directional microphone which sharply catches the intended sound. This directional microphone is helpful for the removal of background noise in the simple sound source exploration and in abnormal sound detection. Flat frequency characteristic from 50 Hz to 20 kHz and sharp detection with high S/N ratio provide high sensitive detection of various sound coming from the specific direction. By combining the acoustic vibration monitor BL-1100, only the intended frequency or sound is focused and caught clearer.
-
product
MEMS Microphone Test
The market is driving the need for improved voice recognition for security, automobile infotainment control, VoIP, accurate language translation, voice-activated consumer devices and high precision hearing aids. The latest next-generation microphones require highly accurate precision testing with SNR tests up to 78 dB with high parallelism, high UPH, in a high volume production environment.
-
product
Noise Monitoring Kit
LxT NMS SoundExpert
In addition to the SoundExpert LxT meter, this kit includes the EPS042 protection case and D-cell battery pack, the EPS2116 microphone protection shroud, and EXC010 10 ft. cable. Using D-cell alkaline batteries, allows the noise monitor to be smaller and lighter; avoid the expense of shipping heavy lead acid batteries and the hassle of recharging. You can transport it easily to your site, deploy it, measure data, retrieve your system, download the data, and issue your report.
-
product
everyday measurement microphone kit
cm-120
The mic bag is a little wonder. On one side are two pockets for microphones and on the other are pockets for mic stand clips, windscreens and other necessities. The bag is fully padded to protect its contents and includes both a long zipper for completely opening the bag as well as a convenient carrying handle. The CM-120 ships with an universal mic clip and cool blue foam windscreen in its interior pockets. This is a quality package at a great price.
-
product
Handheld Audio Analyzer
PAA3X
The PAA3X is a highly accurate handheld audio analyzer that gives sound engineers a rich array of sound analysis tools. The system features both 61-band and 31-band real time spectrum analysis, RT60 reverb time measurement, SPL and line meter, internal signal generator, EQ setting program, microphone calibration and speaker phase checking abilities. All functions and menus can be accessed through a central jog dial, leaving your other hand free to adjust audio settings. The large color LCD screen has an adjustable brightness to help you see in a dark or well-lit environments alike. The PAA3X also features a "screen capture" function allowing users to save images of the screen to an SD card in BMP format for later reference. The detachable precision microphone can be placed remotely via the included 5-meter extension cable, offering flexible on-site operation management. With all this plus a built-in rechargeable lithium-ion battery, the PAA3X is a must-have multifunctional tool for all serious audio engineers.
