Filter Results By:
Products
Applications
Manufacturers
FET
Rely on an electric field to control the shape and channel of a charge carrier in a semiconductor material.
-
product
PXI Solid State MUX, 4 bank, 40 channel
40-680-004
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Solid State Relay with Power FET Switch Protected Against Short Circuits and Overload Currents
Part No. FR75-1
The FR75-1 solid-state relay utilizes a power FET switch that is protected against short circuits and overload currents. The short-circuit protection feature provides protection when a short or overload occurs while the relay is on as well as when the relay is switched into a short. The FR75-1 is packaged in a low-profi le mini-DIP metal package.MSL 1Available options include:FR75-1 0.25Adc, 60Vdc Load; 3.8-5.5Vdc Control; through hole mounted
-
product
Isolated Digital Input/Output Card
PCI-IDIO-16
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
product
3000W-3200W 3-Phase Input Industrial AC-DC Power Supplies
TPS3000
The TPS3000 industrial AC-DC power supplies offer output power up to 3.2kW in a 2U high package with 3 phase supply input.Features include voltage and current programming, remote on/off, remote sense, a standby supply, PMBus communication, built in ORing FET and wide operating temparature range of -40°C to +70°C
-
product
FAult Detector and OScilloscope 7 Functions in 1 Device
FADOS7F1
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
Usage of FADOS7F1: Determining faults of all types of electronic cards such as electronic cards of medical devices, textile and any other machines; automobile electronics; computer, monitor, TV, etc. Electronic Components Test: IC, transistor, FET, IGBT, resistor, capacitor, indicator, ect. This device is used to determine the faults at all these electronic components.
-
product
Solid-State Relays Packaged in a 16-Pin DIP
Series C75-2
Series C75-2 solid-state relays are packaged in a 16-pin DIP, with surface-mount or through-hole mounting available. They utilize a power FET switch that is protected against overload and short-circuit currents. 2S versions provide an open-collector trip status feedback to the relay’s control side. 2SH versions add an internal transient voltage suppressor for inductive loads.MSL 6C75 relays are controlled with 4.5-5.5VdcC = Through-hole mount SC = Surface mountAvailable options include:C75-2 1A, 60Vdc Load; short-circuit protectionSC75-2 1A, 60Vdc Load; short-circuit protection C75-2S 1A, 60Vdc Load; short-circuit protection and trip satusSC75-2S 1A, 60Vdc Load; short-circuit protection and trip status C75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip statusSC75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip status
-
product
JFET Input Amplifiers
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
product
FET DIP Meter
* 1.3 to 30 MHz coverage* Small 350 uA meter movement* Five coils covers HF HAM band*95 turn #36 AWG coil comes pre-assembled* Measures 5.5 x 2.5 x 1.1 inch* 9 volt battery operation
-
product
Solid-State Relay with Power FET Switch to Protect Against Overload and Short-Circuit Currents
Part No. SR75-2
The SR75-2 solid-state relay utilizes a power FET switch that is protected against overload and short-circuit currents. The short-circuit protection feature not only provides protection should a short or overload occur while the relay is on, but will provide protection should the relay be switched into a short. It comes in through-hole or surface-mount 16-pin DIP packages.MSL 6Available options include:SR75-2 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; through-hole mountSR75-2S 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; surface mount
-
-
product
Digital Integrated FET Regulators
Renesas' digital power conversion and management ICs combine an integrated synchronous step-down DC/DC converter with key power management functions in a small package, resulting in a flexible and integrated solution.
-
product
Automotive Power
The automotive power lineup can support a variety of automotive system requirements and includes intelligent power switches, thermal FETs, MOSFET drivers, and a motor driver.
-
product
PXI Solid State MUX, 4 pole, 40 channel
40-680-404
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Terminal Block For 34925A Multiplexer
34925T
The Keysight 34925T is a terminal block for the 34925A 40/80-channel FET multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34925A module.
-
product
FET Solid State Switch, 300 kHz to 8 GHz, SPDT
U9397A
The Keysight U9397A solid state switch maximizes your frequency range from 300 kHz up to 8 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
-
product
Active FET Probe Kit 1.2 GHz, 10x, ±40 V
CT4121
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design.
-
product
IndustryPack Module
IP-OptoISO-16
The IP-OptoISO-16 is an IndustryPack Module with 16 optically controlled FETs [switch]. Each FET acts as a single pole normally open photovoltaic relay. The solid state approach has several advantages including bounce free operation, low on resistance, long life, fast switching, and higher reliability when compared to relays.
-
product
Active Differential Probe
DF-600
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
product
Solid State Relays for Switching Heavy Loads with Physically Small 6-pin DIP Package
Part No. ZD20CF
Series ZD20CF solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD20CF 2A, 60Vdc Load; 8-20mAdc Control; through hole mountedSZD20CF 2A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
product
Switch Drivers
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
product
Low Profile Solid State Relays, MIL-PRF-28750 Screened
Part No. LD24KK
The Series LD24KK solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input and output are optically isolated to protect input logic circuits from output transients. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1Available options include:LD24KK 5A, 270Vdc Load; 4.2-16Vdc Control, Short Circuit Protection and Trip Status
-
product
Miniature Solid-State Relays
Series C47F
The Series C47F miniature solid-state relays utilize a photovoltaic generator driving high-performance power FET chips to provide low-output on resistance and high-output switching capability. The virtual elimination of offset voltage makes these relays ideal for low level switching applications as well. Bidirectional switching versions (Series C46F) are available. MSL 6Available options include:C47F-10 1.75A, 50Vdc Load; 3.8-32Vdc ControlC47F-20 1A, 90Vdc Load; 3.8-32Vdc Control C47F-30 0.6A, 180Vdc Load; 3.8-32Vdc ControlC47F-40 0.4A, 360Vdc Load; 3.8-32Vdc Control
-
product
PXI Matrix Switch Module
PXI Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
Mezzanine System
5235
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
product
DC/DC Converter 60 W
XRCM60-12DQF
DC/DC converter with 60 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | output 12 V | operates in temperatures from -40 to +70 °C | provides 20 ms hold up time | O-ring FETs and built-in fuse
-
product
Solid State Relays for Switching Heavy Loads with Physically Small 6-pin DIP Package
Series C60
Series C60 solid-state relays use an advanced design capable of switching very heavy loads in a physically small 6-pin mini-DIP package. These relays have a power FET output that ensures low ON resistance, no offset voltage and low leakage current. They are versatile and can be used to switch AC, bidirectional or DC loads.MSL 6C = Through-hole mount SC = Surface mountAvailable options include:C60-10 2.5Adc, 60Vdc DC-Load; ±1.25Adc, ±60Vdc AC-Load; 10-50mAdc ControlSC60-10 2.5Adc, 60Vdc DC-Load; ±1.25Adc, ±60Vdc AC-Load; 10-50mAdc ControlC60-20 1.5Adc, 100Vdc DC-Load; ±0.75Adc, ±100Vdc AC-Load; 10-50mAdc ControlSC60-20 1.5Adc, 100Vdc DC-Load; ±0.75Adc, ±100Vdc AC-Load; 10-50mAdc ControlC60-30 1Adc, 200Vdc DC-Load; ±0.5Adc, ±200Vdc AC-Load; 10-50mAdc ControlSC60-30 1Adc, 200Vdc DC-Load; ±0.5Adc, ±200Vdc AC-Load; 10-50mAdc ControlC60-40 0.5Adc, 400Vdc DC-Load; ±0.25Adc, ±400Vdc AC-Load; 10-50mAdc ControlSC60-40 0.5Adc, 400Vdc DC-Load; ±0.25Adc, ±400Vdc AC-Load; 10-50mAdc Control
-
product
PXI Solid State MUX, 5 bank, 32 channel
40-680-003
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
MIL-PRF-28750 Solid State Relay
Part No. KD44CF
The KD44CF solid-state relay utilizes MIL-PRF-28750 test methods. These relays feature fully floating power FET outputs that allow the load to be connected to either output terminal and provides a low ON resistance. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1 Available options include:KD44CF 2Adc, 60Vdc Load; 3.8-32Vdc (bias voltage), 250µA (CMOS) Control;
-
product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Saluki SE4002 FET Input Preamplifier
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
