Filter Results By:
Products
Applications
Manufacturers
-
product
EV Charging Station Tester
EV : ChargeCheck
The EV Industry’s Charging Station Tester of Choice. • Simulates an electric vehicle • Tests J1772 (type 1) tethered leads • Tests IEC62196 (type 2) sockets • Tests IEC61851-1 mode 3 communication compliance • Tests for correct polarity • Tests for earthing presence • Tests contactor actions.
-
product
EV Charging Station
Residentual
BENEFITS OF RESIDENTIAL CHARGING: *Charge up to 7x faster than the Level 1 cordset that came with your electric vehicle. *Level 2 (240V) charging stations are more affordable than ever – starting at just $379! *Tax incentives and rebates offset purchase and installation costs, up to 100% in some areas *It’s more convenient to charge at home than using a public station. *Indoor/Outdoor rated (fully sealed NEMA 4 enclosures) *The Level 1 cordset that came with your electric vehicle can be used as a portable charging station or for a second charging station when you have company with an EV.
-
product
M2M & IoT Installation Tools
Berkeley Varitronics Systems, Inc.
Handheld installation receivers for realtime 3G and 4G RSSI and RSRP signal strength of nearby wireless carrier base stations for M2M & IoT site surveys and antenna alignment for smart meters, EV charging stations, vending machines, wireless kiosks, digital signage, ATMs and more.
-
product
DC Electronic Load
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
product
EOL/Functional Testing
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
product
Total Energy System
5000
The electric vehicle (EV) charging market is rapidly expanding, with more and more people switching to electric cars. As the demand for EV charging stations increases, so does the amount of energy that is being exchanged. This energy exchange market is already massive, with charging peaks reaching into the megawatts of energy. With this amount of energy comes a significant amount of revenue, which requires the most accurate billing possible. That’s where TESCO’s Catalog No. 5000 – Total Energy System comes in. The Catalog No. 5000 is a double duo system that enables the testing and accuracy verification of Electric Vehicle Service Equipment (EVSE) and Field Test Equipment for testing EVSE’s in the field. This system is a dual-purpose DC and AC System and includes both a 100A AC (ACT-100) Test System and a 200A DC Test System (DCT-200).
-
product
High Power DC Electronic Load
63200A series
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
product
Electric Vehicle Service Equipment Test System
T4350
With the growing demand for electric vehicles (EV), there needs to be a simple and accurate method to test EV charging systems. Test the accuracy of AC and DC voltages and currents with TESCO’s Electric Vehicle Service Equipment (EVSE) Test System TS400. The TS400 is a valuable set with complete testing capabilities and caters to every possible EVSE charging protocol in the world (AC and DC). EV charging stations are popping up all over as the sale of electric vehicles increase. Many states or counties are now mandating testing for these charging stations. TESCO’s TS400 makes testing these chargers easy! TESCO’s EVSE Test Systems test the accuracy of energy delivery using a transactional mode compatible with Handbook 44 provisions. The TS400 Test System includes a T4000 EVSE Tester and a PL4000 EV Load Emulator. Reach out to your TESCO Representative for more information!
-
product
Handheld EV Analyzer
EDV100
EVD100-Handheld EV Analyzer is a monitor and diagnostic equipment for electric vehicles DC charging process.
-
product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
product
In-Line Charge Amplifiers
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
product
Charge Sensitive Preamplifier-Discriminator
A101
Model A101 is a hybrid charge sensitive preamplifier, discriminator, and pulse shaper developed especially for instrumentation employing photomultiplier tubes, channel electron multipliers and other low capacitance charge producing detectors in the pulse counting mode. The A101 is widely used in laboratory and commercial applications for mass spectrometers, laboratory and research experiments, aerospace instrumentation, medical electronics, and electro-optical systems.
-
product
Charge Integrator Amplifiers
AD8488
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
product
Regeneration Station
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
product
Soldering Stations
SM-878AD
*Module: 878AD*Display: LED*Power Rating:700W *Air Flow: 120L/Mints*Temperature: 100-450DEGREE*Noisy: <45dB
-
product
Charge Meter
NK-1001A/NK-1002A
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
product
Charge Controller
The intelligence of an AC charging station or an AC charging infrastructure is largely determined by the charge controller used. A smart charge controller has the primary task of controlling and monitoring the charging process of an electrical vehicle.The features that characterise a smart charge controller include communication with a backend system and the associated authorisation of users, as well as the efficient distribution of load currents by means of dynamic load management to prevent an overload of the existing AC system.
-
product
Charge Plate Monitors
Our charge plate monitors the voltage of the battery and the voltage of the battery.
-
product
DC-DC Charge Pumps
Charge pumps – inductorless boost converters – from ams operate at up to 90% efficiency.
-
product
BASE STATION
Optional ship-board base stations provide two-way satellite communications with your drifting buoys.
-
product
DC/DC With UPS And Charge Controller
PCM-PS402-512
WINSYSTEMS’ PCM-PS402-512 is a wide input range, triple output PC104 DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40° to +85°C without a fan or heatsink making it ideal for industrial applications.
-
product
Training Administrator Station
Model 8843
The Training Administrator Station (TAS), which can pair with up to four Model 8813 and/or Model 8833 training benches, is a remote controller that uses a touchscreen Microsoft tablet communicating over a closed WIFI network.
-
product
Engineering Lab Stations
Engineering Lab Stations provide an all-in-one solution to engineering education by combining hardware, software, and courseware to give real hands-on experience to students in electronics, mechatronics, and communications courses.
-
product
Utility Field Station
1060
The Utility Field Station (Catalog No. 1060) is a lightweight, easy-to-use tool that helps you easily bring equipment in and out of the field while also providing a portable work station on site.
-
product
Complete Probe Station
BD Series
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
product
Weather Stations
Is a facility, either on land or sea, with instruments and equipment for measuring atmospheric conditions to provide information for weather forecasts and to study the weather and climate.
-
product
Manufacturing Test Station
Scan Executive
The Scan ExecutiveTM Manufacturing Test Station is used to apply the same IEEE 1149.1 tests that were developed and used in the lab in a high-volume manufacturing environment without requiring additional development.
-
product
CP TEST STATION
T-1
3 hole terminal board3 binding postsClear terminal boardSeven colors from stockFits 1.6" OD riser pipeUV stabilized color protectionHigh impact resistanceFire resistant"Easy Grip" top for easy opening with gloves"Anti-Spin" gasket prevents twisting
-
product
Capacitor Charging Power Supplies
Excelitas Capacitor Chargers are tailored to meet your exact needs by configuring modular platforms based on proven designs. Single-phase AC input designs are capable of up to 6 kW of output power and our three-phase designs provide up to 35 kW of output power. A modular design approach results in lower cost, higher reliability, and faster time-to-market. Typical applications for capacitor charging power supplies include flashlamp pumped laser systems (Nd: YAG, pulsed lasers, dye lasers, Intense Pulsed Light Systems (IPL) and aesthetic Medical Laser Systems, Medical Holmium YAG Laser), excimer lasers, pulsed UV curing and sterilization, radar and RF systems.
-
product
Smart Refrigerant Charging Kit
HUB4
UEi Test & Measurement Instruments
The HUB4 gives the ability to wirelessly get Vapor and Liquid pressures via the WPP1 probes and Vapor and Liquid temperatures via the WPC1 probes, all via the free UEi Hub App. Easy to use and a rugged design make the App and probes an excellent addition to any technician's toolbox.
