Fibre Optics
Field of optic fiber application.
-
Product
Optical Power Meter
RA3209
-
Radiasun International Group Ltd.
Portable optical power meter is an accurate and durable handheld meter designed for the installation, operation and maintenance of optical fibre network. Portable optical power meter is a compact device with backlight switch and auto power on-off ability. Besides, portable optical power meter provides ultra-wide measurement range, high accuracy, user self-calibration function and universal port. In addition, portable optical power meter displays linear indicators (mW) and non-linear indicators (dBm) in one screen at the same time.
-
Product
O/E Converter
TIA-1200
-
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
Product
635nm Visible Light Source
VLS-40
-
The KD Optics VLS-40 is an easy to use, hand-held, visible source used for testing fibre optic cable installations. It is especially useful when testing fibre optic cables close to the terminal equipment. The unit is pocket sized with a long battery life, making it ideal for local fault finding and continuity checking of fibres.
-
Product
Dual 2 Channel Fibre Optic Mux FC/APC
40-815-022
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Fibre Tracer
FT20
-
The KD Optics FT-20 is a small, hand-held, visible source used for tracing multimode fibre optic cables and is especially useful for identifing a single fibre in a multi-fibre cable. The unit has a bright LED output with a 2km range and is modulated at 2Hz.
-
Product
PXI Quad 2x2 Fibre Optic Mux MU
40-860-342
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
"Signal Transporter"
LTX-5520
-
The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fibre optic links ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled at 50 mega-samples per second, multiplexed and transmitted serially over an optical fibre at a 1 Gb/s data rate.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
Product
"Signal Transporter"
LTX-5510
-
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode) SC M50
40-860-212-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
-
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
-
Product
STANAG3910/EFEX Modules
-
AIM’s STANAG3910/EFEX test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O. Configurations with dual redundant concurrent HS/LS Bus Controller (BC), Multiple Remote Terminals, and Chronological/Mailbox Bus Monitor operation with full HS/LS protocol error injection/detection, multi-level triggering, advanced capture/filtering and real time bus recording, time stamping and physical bus replay ensure your bus integrity. Support for EFAbus Direct Digital Links (DDL), Fibre Optic DDL (FODDL) and EFAbus Express extensions (Mixed Mode and Dual Mode operation) are available. To support the French ‘Rafale’ aircraft, modules are available with an Electrical Front End. Single Function variants support cost effective solutions. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our STANAG3910 modules.
-
Product
Next Generation Subsea Inertial Navigation Systems
TOGSINS
-
The new TOGSINS builds on core TSS fibre optic gyro technology by incorporating inertial navigation (INS) capability. As with TOGS, it is available in three standard heading accuracy variants: 0.1° (TOGSINS1), 0.3° (TOGSINS3) and 0.5° (TOGSINS5), all rated for operational depths to 4,000m or 6,000m giving you a range for all your needs.Inertial position data is produced using an INS algorithm, within the firmware framework of TOGS, whilst attitude data is delivered via accurate roll/pitch measurement of 0.01° (TOGSINS1) and 0.05° (TOGSINS3 and TOGSINS5), and a heave performance of 5cm or 5%.
-
Product
PXI Single 2 Channel Fibre Optic SC/PC
40-855-212
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Industrial Data Communications
-
In this section you will find hundreds of industrial-grade infrastructure, gateway and conversion products for all major data communications protocols. Amplicon can specify a solution for almost any data communications task, including transmission solutions for wireless, copper and fibre optic based links.
-
Product
X-Ray Detector
XRT Detector Onyx
-
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
"Signal Transporter"
LTX-5525
-
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
Product
AIM System Solutions
System
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
Product
Dual 2 Channel Fibre Optic Mux FC/PC
40-815-122
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Endoscopes
-
Originally designed for the medical sector, endoscopes are the ideal tool for inspection and maintenance today. Endoscopes offer new perspectives to viewing the insides of machines. Thanks to their flexible fibre optic cables and light weight enclosure, these extraordinary endoscopes are the ideal tool for inspection and maintenance. Endoscopes can locate problems and conflicts of the system very easily and quickly, allowing for preventative measures to be taken without the need to dismantle the machinery first. Complex dismantling of machines is usually very time and cost intensive. With the help of endoscopes, inspections in an industrial sector can therefore be organized considerably faster, more aimed and more cost-efficiently Endoscopes are used mainly by electricians, security personnel, specialists in the professional sector, and mechanics of all types. All of our endoscopes are ***Not for medical use***
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Single 4 Channel Fibre Optic Mux FC/APC
40-850-014
Fiber Optic Switch
The 40-850-014 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Optical signal transmission
Bus systems
-
Allows for the transmission of high speed CAN signals via optical fibre cables during EMC tests or when there are great potential differences (high voltage).
-
Product
Fiber Optical Cabling
-
An optical fiber, or optical fibre in Commonwealth English, is a flexible, transparent fiber made by drawing glass or plastic to a diameter slightly thicker than that of a human hair.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Temperature sensors
TC-03
-
The Temperature Chain TC-03 is a spliceless chain of several fibre optic temperature sensors in series. The sensors are all contained in a 1mm stainless steel tube which is directly connectorised on one end.
-
Product
Fibre Optic Laser Encoders
-
The RLE system is a unique, advanced homodyne laser interferometer system specifically designed for position feedback applications.
-
Product
Multi Channel Optical Fibre Verification
-
The multi-channel optical fibre test system is used in the development and qualification of single mode optical fibres. The fibres are exposed to environmental influences in a climatic chamber in order to analyse the data on insertion loss and reflection. In addition, the current temperature in the climatic chamber is documented. Insertion loss measurement is performed with the help of an optical power meter, laser sources and optical switches. An Optical Time Domain Reflectometer (OTDR) from Exfo is used for the reflection measurements. The system was designed for the simultaneous characterization of 15 sample fibres and one reference fibre.
-
Product
Fiber Optics
-
The use of fiber optics as light guidance allows great modularity and flexibility in the setup of an optical measurement system. Optical fibers can be made of many materials, such as plastic, glass, and silicates (SiO2). For high-quality fibre optics, as used in spectroscopic applications, synthetic fused silica (amorphous silicon dioxide) is used, which can be intentionally doped with trace elements to adjust the optical properties of the glass.
