Battery Internal Resistance
-
Product
Advanced Earth Resistance Testers
-
Precision Mastech Enterprises Co.
Specialized, high-precision instruments used to measure the efficiency of grounding systems (earthing) in industrial, commercial, and residential settings.
-
Product
Standard 0.95 (26.90) - 4.50 (128.00) Battery Probe
CP-2LB-12
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 128Full Travel (mm): 3.25Recommended Travel (mil): 118.1Recommended Travel (mm): 3.00Overall Length (mil): 472Overall Length (mm): 12.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Lead-acid Storage Battery Analyzer
Mega Series
-
The Express-estimation of a condition of the lead-acid chemical power sources. The Analyzer allows to estimate of the power characteristics of the battery during 5-15 seconds without carrying out of long control electric tests.
-
Product
Battery Powered, Stand Alone Water Level and Temperature Data Logger
Level1000
-
The Level1000 is a rugged, submersible, battery powered, stand alone, water level and temperature data logger. Its stainless steel enclosure makes it perfect for use in lakes and streams. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 16,383 measurements.
-
-
Product
Battery Analyzers
CA 1550 – Military Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
Battery Monitoring System
S5
-
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
Product
Dual channel portable lightweight battery charger
TS2X020
-
The TS2X020 is a portable lightweight battery charger intended for rapid charging of vehicle batteries in the field without the attendant weight penalties usually associated with the operation. The charger is a constant voltage unit, and the charging current is regulated by the battery terminal voltage, with current limit of 20 Amps on 24v output, and 40 Amps on 12v output. Switch mode technology provides high efficiency; both in power to weight ratio, and input to output ratio.
-
Product
Counter Battery
-
This all fuels the need to redefine effective approaches in counter battery, in particular for the functions usually fulfilled by weapon location radars: target acquisition, fire control and prediction of impacts.
-
Product
Lithium battery 128kWh Lifepo4 Battery pack 280Ah with BMS for Solar Energy Storage System
SPVLI-128kWh
-
Zhejiang Sandi Electric Co., Ltd
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Battery Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
Battery testers are the class of instruments designed to assess the condition—the charge, impedance, ripple current, or other measurement—of batteries to ensure they are working as required. Just as batteries have a very wide range of sizes and uses, so do battery testers.
-
Product
Battery Management Systems
-
A BMS is the intelligent component monitoring and managing any lithium-ion battery pack. It is the brain behind the battery and has a key role in its levels of safety, performance, charge rates, and longevity.
-
Product
Laboratory Battery Tester
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
Battery Management Systems Testing
System
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
Product
Contact Resistance Meter
CRM 100B+
-
SCOPE introduces its next generation of hugely popular CRM series contact resistance meter, CRM100B+ in all new super light avatar, based on cutting edge ultra capacitor technology. CRM incorporates some state of the art hardware & smart software features making it a must have tool for testing & maintenance engineers.
-
Product
Battery Tester
6470 BT
-
Standard Electric Works Co., Ltd
2000 counts. DC Voltage measurement. 4-wire resistance measurement. Data hold function. Low battery indication. 9V DC power supply. Measure battery types: Li-ion, Ni-Cd, Ni-MH. Simple operation. Lead resistance and contact resistance eliminated.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Electronic Resistance Store
MPS2
-
The MPS2 module is a mezzanine module designed to form DC resistance in two channels with a four-wire measurement circuit. MPS2 is installed on the mezzanine carrier - the NMU module and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NMU module. The NMU module together with the mezzanines installed on it forms a VXI module of the size C-1 and is used to create information measuring VXI systems.
-
Product
Non-contact Sheet Resistance /resistivity Measurement Instrument
EC-80
-
*Easy operation and compact design*Auto-measurement start by inserting a wafer under the probe*Easy set up to measurement condition by JOG dial*5 types of model for each measuring range
-
Product
Observational Systems: Data Handlers And Battery Packs
-
Data loggers allow users to connect a variety of sensors to a single controller that manages, stores, and sends the collected data as a single data stream.
-
Product
High Performance EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
The 6V series battery test system uses a full-bridge circuit topology with a higher digit sampling chip. It can provide higher precision and more dynamic test data, and can provide a complete test program for mainstream lithium-ion batteries and batteries with a variety of material systems such as sodium batteries.
-
Product
Battery Charger-Analyzer for small battery systems
Minicharger
-
The Minicharger is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries
-
Product
(Automatic Redundant Battery Selector With Source Control And Monitoring)
ARBS 2600
-
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Flat Panel Display
NC-600
-
*Non-stop and non-contact sheet resistance measuring of thin film on glass runs through on conveyer*1 to 10 number of probe by sizes of glass is attachable*Glass collision prevention function*Continuous test data report to the host computer
-
Product
Battery Capacity Analyzer
600B
-
The 600B Battery Capacity Analyzer addresses the need to test and maintain sealed lead acid (SLA) batteries used in backup power UPS, emergency lighting, fire alarms, security systems, and many other electrical systems. By quickly characterizing a battery's response to a load resistance, the meter displays the remaining battery capacity as an indicator of the battery's health.
-
Product
New Resistivity Inversion Software
EarthImager 3D
-
AGI is proud to introduce the new EarthImager 3D resistivity and IP inversion software. This software inverts resistivity and IP data acquired with electrodes arranged in boreholes and/or on the surface and presents a 3D volume of inverted resistivity data with advanced volume rendering technique. The final resistivity or IP image-volume can be rotated in any orientation, zoomed in and out, and translated to anywhere inside the image window in order to see the volume of interest in detail. Colors representing areas of less interest can be made transparent so that the shape of a pollution plume, for example, can be visible. With EarthImager, 3D resistivity inversion can be as easy as two steps: Read Data and Start Inversion with only a few mouse clicks.
-
Product
Clamp-On Type Earth Resistance Tester / Leakage Current Clampmeter
KM 1620 / KM 1720
-
Kusam Electrical Industries Limited
KM-1620 / KM 1720 single-jaw type Earth Resistance Tester is widely used for earth resistance testing of the equipments in the field of power, telecommunication, as well as the other electrical equipments. It features easy operation, high-accuracy and good adaptation of testing environment.
-
Product
4-Way Resistive Power Dividers DC To 27 GHz
-
Pulsar Microwave manufactures resistive dividers from DC to 27 GHz. They have a rated input power of one half watt maximum. VSWR of 1.5:1 or better maintained throughout band at all ports. Resistive dividers can be fitted with SMA male or female connectors and are available in three outline packages.
-
Product
Terminal High Resistance
-
Terminal High Resistance Standards that can be rack or bench mounted. The 6636 Series provides a set of customer chosen precision resistance standards enclosed in a temperature controlled chamber.
-
Product
Field-installation Type Electric Resistivity Meter (Two-Wire Transmission)
HE-300R
-
HE-300R connects resistivity sensor (ERF Series) and measures resistivity and temperature in the sample water.It is suitable for measurement of UPW resistivity.
